轉閥總成 的英文怎麼說
中文拼音 [zhuǎnfázǒngchéng]
轉閥總成
英文
valve packe-
Carefully remove the handwheel and turn indicator sleeve assembly, leaving the valve at its balance set point
小心拆卸手輪,並旋轉指示器套筒總成,將閥門保留在它的平衡設置點上。The leading products are more than 100 categories with gps, wiper motor assembly, power window regulator assembly, door locks, electric fans, and door lock actuators, blowers, cab tilting system and switches etc. the products were not only delivered as oem to nearly all the automakers in china but exported to over twenty countries in america, europe, south east asia and middle east etc. the group has passed the
主導產品為中歐旅居車房車系列駕駛室液壓翻轉器系列egr閥系統汽車導航系統雨刮總成系列玻璃升降器總成系列車門鎖總成系列電子風扇系列中控鎖系列暖風電機系列傳動系統以及各類車用開關等一百多種產品。主要為國內各大汽車製造廠配套,並出口歐美中東及東南亞等國家。With the handwheel / turn indicator sleeve assembly still at its balance set point indication, reinstall them on the valve stem and hold in place with the 1 / 4 " retaining bolt
這時手輪/旋轉指示器套筒總成仍然位於平衡設置指示點上,將它們重新安裝到閥桿上,並用1 / 4英寸固定螺栓固定在其位置上。Remove # 1 check assembly by using your hands to unscrew ( turn counter - clockwise ) check and remove through top access port
通過頂部檢修口,用手按逆時針方向旋轉止回閥螺紋,拆卸1號止回閥總成。The check assemblies are threaded into the body. to remove the first check assembly, rotate the check module by hand counterclockwise
這種止回閥總成是通過螺紋旋進閥體的。為了拆卸第一止回閥總成,要用手逆時針方向旋轉止回閥模塊。Holding the check valve module in both hands, rotate the assembly quarter turn. this will disengage the disc assembly, spring and seat cover into individual components
雙手握住止回閥模塊,將總成旋轉四分之一轉。這將把閥瓣總成、彈簧和閥座蓋分解成獨立的部件。As shown on the schematic drawing on the right, the closing member ( stem and disc assembly ) of the figure 85 or 90m frostproof sillcock operates by turning the handle in a clockwise manner to close and counter - clockwise to open
正如右側示意圖所示,型號85或90m防凍灑水龍頭上最靠近的部件(閥桿和閥瓣總成) ,是通過順時針方向旋轉手柄來實現旋轉關閉和逆時針方向旋轉開啟。Using the centerline access bar, spin the check assembly from the 9 o ' clock position to the 12 o ' clock position, then ( without letting go of the access bar ) push the cam assembly slightly downstream so that the clapper is now parallel to the valve body
用中心線接近棒將止回閥總成從時鐘指針9點的位置旋轉到12點的位置,然後(不要松開接近棒)將凸輪總成稍微往下游推使得閥瓣與閥體平行。分享友人