通用燃燒器 的英文怎麼說

中文拼音 [tōngyòngránshāoqì]
通用燃燒器 英文
universal combustion burner
  • 通 : 通量詞（用於動作）
  • 用 : Ⅰ動詞1 （使用） use; employ; apply 2 （多用於否定: 需要） need 3 （敬辭: 吃; 喝） eat; drink Ⅱ名...
  • 燃 : 動詞1. （燃燒） burn 2. （引火點著） ignite; light
  • 燒 : Ⅰ動詞1 （使東西著火） burn 2 （加熱或接觸某些化學藥品、放射性物質等使物體起變化） cook; bake; hea...
  • 器 : 名詞1. （器具） implement; utensil; ware 2. （器官） organ 3. （度量; 才能） capacity; talent 4. （姓氏） a surname
  • 通用 : be in common use; be current; apply or be used universally
  • 燃燒 : （物質劇烈氧化而發光、發熱; 燒） burn; kindle; flame; set on fire; [化學] combustion; inflammation; ignition
  1. Abstract : apply computer simulation to the distribution pattern of air - flow without considering the cold condition of the combustion and compare the flow patterns under different designed circumstances. and the effect of the design of the partition in the air way of the burner on the flow and mixture of gas and air is especially studied. the result shows that the design of partition plays a very important role in strengthening the mixture of gas and air, but increases the loss of the resistance in the air way and the total pressure of the air way in same working conditions needs increasing

    文摘:應用計算機模擬的方法，在不考慮燃燒的冷態情況下，研究了熱風爐燃燒室內的氣流分佈規律.在此基礎上，比較了2種不同設計方案的氣流流動特徵，尤其是研究了燃燒器空氣通道內阻流板的設置與否對空氣和煤氣的流動和混合的影響.結果表明，阻流板的設計對加強空氣和煤氣的混合有著極為重要的作用，同時也增加了空氣管道的阻力損失，在同樣的工況條件下需要提高管道系統的總壓力
  2. Automatic forced draught burners for gaseous fuels ; german version en 676 : 2003

    氣體燃料用自動壓力通風燃燒器
  3. General specification for industrial oil and gas burners

    工業燃油燃氣燃燒器通用技術條件
  4. The top - firing air and gas self - preheating hot blast stove adopts a patented burner and high blast temperature bypass flue

    摘要頂燃式空氣、煤氣自身雙預熱熱風爐採用了頂燃式燃燒器熱風爐專利的燃燒器技術和高溫旁通煙道技術。
  5. Gas - appliances with atmospheric gasburners for installations in bakeries and confectioneries

    麵包房和糖果廠設備用帶自然通風燃燒器的煤氣設備
  6. Aiming at such problems in combustion system of homemade middle and miniature boiler, as a complex system with the character of dead zone, time variation, serious non - linearity, large time delay, coupling and a lot of disturbance, this paper presents a new set of optimal control resources. by using well - matched control method on system, stable automatic running is realized. having the serious divulgence coals difference a lot from each other in character, instability of chemistry, value of lowest emission of heat, home - made boiler controller is not at all ideal. instead of traditional model that controls the ratio based on proportional control or with the correct signal of the amount of oxygen, this paper, combined with intellect control theory - - fuzzy control and self - optimizing concept, propounded a kind of fuzzy self - optimizing controller to be used in air supplying system of the boiler, and expatiates on the idea of dividing the control process into two parts, dynamic and static to realize, thus meets the demand of homemade boiler economic running

    本設計針對國產中、小型電站鍋爐燃燒系統參數時變、嚴重非線性、干擾因素復雜、耦合嚴重、模型不易確定的特點，提出多變量協調控制方案，解決了系統可控性差，難以實現穩定自動運行的問題；在此基礎上，改變以往以煙氣含氧量控制送風的傳統模式，針對國產電站鍋爐設備主體及一、二次送風迴路泄露嚴重，煤種混雜、成分不穩定、燃燒發熱值低、燃燒效率不高等問題，應用智能控制理論中的模糊控制技術，結合自尋最優控制的思想，設計了一種模糊自尋優控制器，應用在電站鍋爐送風控制系統上，並闡述了動靜態兩種實現途徑，通過在線優化風煤配比，實現最佳經濟燃燒，切實保障了鍋爐的經濟運行。
  7. The burners of 220 t / h boiler in henan shenhuolv power plant were retrofitted by using the pulverized coal burners with stabilized - firing cavity and cutting down the distance between up - primary air and down - primary air etc. technologies, thus the boiler was successfully converted from originally designed burning high calorific value coal to low calorific value coal, the boiler could operate stably at 50 % load without oil - firing aid and the thermal efficiency of boiler reached 89 %

    摘要採用穩燃腔煤粉燃燒器並集中布置上、下一次風等技術對河南神火鋁電廠220t / h鍋爐燃燒器進行改造，成功地將該爐原設計燃用優質煤改燃為普通煤，並取得了改造后50 %負荷可無油穩定運行，鍋爐熱效率達到89 %的良好效果。
  8. Heating boilers - part 6 : heating boilers with forced draught burners - specific requirements for the domestic hot water operation of combination boilers with atomizing oil burners of nominal heat input not exceeding 70 kw

    供暖鍋爐.第6部分:帶有強制通風燃燒器的供暖鍋爐.帶有公稱熱輸入功率不超過70kv的自動燃油燃燒器的組合鍋爐家用熱水供暖操作的特定要求
  9. Gas appliances ; forced air gasburners with ventilation in bakeries

    煤氣設備.麵包房用帶通風裝置的鼓風煤氣燃燒器
  10. By virtue of the experiments carried out on the modified pilot - scale biomass gasification system, the temperature field in the gasifier is made explicit. and also some principles about how the temperature, feedstock and extraction mode exert influences on heat value and production rate of gas are attained. in addition, some tentative tests of tar cracking and thermodynamic characteristics of biomass gas burner have been performed, which are that indispensable to design and operation of biomass gasification demonstration project

    接著，通過對生物質中熱值氣化中試試驗系統的多次改造和反復試驗，了解了氣化爐內溫度場分佈，得出了溫度、物料、抽氣方式等因素對生物質熱解氣的成分、熱值和產氣率影響的一些基本規律，並進行了初步的焦油催化裂解試驗和煤氣燃燒器的熱力特性、燃燒特性試驗，為面向工程應用的集中供氣示範項目提供了必要的設計和運行依據。
  11. Whole scheme of frame design of testing flat is proposed as : the host fanner supply the air required by flamer ’ s burning and cooling, the export parameter of the flat varies by different rotate speed of the fanner 、 angle of the fan inlet and the quantity of oil, the measurement of flow in the testing flat adopts the method of fanner dynamics performance test in the nation criterion

    確立了實驗臺結構設計方案：主風機為燃燒器提供燃燒所需的一次、二次進風量及冷卻風量；模擬實驗臺出口煙氣熱流量是通過調節風機的轉速、風門開度及燃油量來改變；實驗臺的流量測量採用風機動力性能測試標準中流量方法等。
  12. Oil controls for vaporizing burners - part 1 : general installations ; safety requirements and testing

    汽化燃燒器的油控制器.第1部分:通用裝置.安全要求和
  13. Heating boilers - heating boilers with forced draught burners - specific requirements for the domestic hot water operation of combination boilers with atomizing oil burners of nominal heat input not exceeding 70 kw

    供暖鍋爐.帶強制通風燃燒嘴器的供暖鍋爐.標稱熱輸入量不超過70kw的用霧化油燃燒爐的組合式鍋爐的家用熱水供熱特定要求
  14. On the basis of annlyzing the main domestic cocurrent combustor, we adopted the up and down - shade - technology to reform the combustonafter researching the characteristics of main coal and its affecting factors, i. e., density of coal dust, granularity of coal dust, firing characteristics, alteration of coal, we put forward the scheme of coal ' s configuration and reforming plan about structure of combustor and its disposal type. finally, we make a debugging of cool and hot performance and operation optimizing

    因此，本文在分析目前國內主要直流燃燒器性能的基礎上，選用了上下濃淡燃燒技術，改造了燃燒器；通過對現場燃燒的主要煤種特性及煤粉濃度、煤粉細度、著火特性、煤種變動等的分析研究，提出了配煤方案和燃燒器的結構、布置方式改造方案；最後進行了冷、熱態性能與運行優化調試。
  15. Welcome at dungs top technological products and system solutions for the burner, heating, air conditioning and process heat industry are our contribution to safe and clean burning of gases and oil for heat production and efficient heat distribution

    我們的貢獻是通過對燃氣和燃油的安全高效清潔衛生的燃燒獲得熱量，我們的產品和系統方案在技術上處于領先的地位，被廣泛地應用於燃燒器工業採暖工業空調工業和工業加熱過程。
  16. Abstract : the in servie tubular heaters built early in refineries and chemical plans have low thermal load and low heat efficiency, therefore measures for technical reform are offered, including ( 1 ) enlarging the surface area of convection tubes to increase the thermal load of rhe convection section ; ( 2 ) increasign the heat interchanging area of radiant tubes ; ( 3 ) changing the height of the chimney ; ( 4 ) using new burner with forced air supply to increase calorific capacityu ; ( 5 ) adding air preheater between the convection section and chimney to enhence the temperature of the air entering the furnace ; ( 6 ) adopting high temperature radiant coating to improve the effect of radiant heat interchanging

    文摘:針對早期建造的煉油廠和化工廠在役管式加熱爐熱負荷和熱效率低的狀況，提出了若干技術改造措施包括，增大對流管表面積以增大對流段的熱負荷；增加輻射管的換熱面積；修正煙囪高度；換用新型燃燒器，變自然通風為強制供風，以增大燃燒器的發熱量，減小過剩空氣系數，節省燃料2 % 3 % ；在對流段和煙囪之間增設空氣預熱器以提高空氣入爐溫度；採用高溫輻射塗料增強輻射換熱效果，從而增加熱源對爐壁的輻射傳熱量和爐管的傳熱量等。
  17. The in servie tubular heaters built early in refineries and chemical plans have low thermal load and low heat efficiency, therefore measures for technical reform are offered, including ( 1 ) enlarging the surface area of convection tubes to increase the thermal load of rhe convection section ; ( 2 ) increasign the heat interchanging area of radiant tubes ; ( 3 ) changing the height of the chimney ; ( 4 ) using new burner with forced air supply to increase calorific capacityu ; ( 5 ) adding air preheater between the convection section and chimney to enhence the temperature of the air entering the furnace ; ( 6 ) adopting high temperature radiant coating to improve the effect of radiant heat interchanging

    針對早期建造的煉油廠和化工廠在役管式加熱爐熱負荷和熱效率低的狀況，提出了若干技術改造措施包括，增大對流管表面積以增大對流段的熱負荷；增加輻射管的換熱面積；修正煙囪高度；換用新型燃燒器，變自然通風為強制供風，以增大燃燒器的發熱量，減小過剩空氣系數，節省燃料2 % 3 % ；在對流段和煙囪之間增設空氣預熱器以提高空氣入爐溫度；採用高溫輻射塗料增強輻射換熱效果，從而增加熱源對爐壁的輻射傳熱量和爐管的傳熱量等。
  18. Mainly by modifying the control logic of the burner management system ( bms ), the defects of the system are redeemed to enable its reliable operation

    通過修改鍋爐燃燒器管理系統（ bms ）的控制邏輯和增加保護的投入，彌補了系統的缺陷，保證滅火保護系統安全可靠地投入使用。
  19. First, we simulate the firebox through realization k - e turbulent model. if experimentation data match to simulated data, we consider the physics model and turbulent model we establish is valid

    首先模擬燃燒器，所選用的湍流流動模型為可實現的-模型，通過用實驗測得的實驗數據與模擬值是否吻合來判斷我們所建立的物理模型及所選用的湍流流動模型的正確性。
  20. Reburning technology is a valid method. this paper focuses on nox - emission problem of traditional units with hot air transferring pulverized coal. the main technical route of this paper is to use the pulverized coal contained within tertiary air to reduce the nox emission as the reburning fuel

    本文主要是針對傳統的缺少有效降低no _ x方法的熱風送粉機組進行研究，通過對制粉系統和燃燒器的改造與調整，利用三次風中的含粉作為再燃燃料送入爐膛，實施再燃燒以降低no _ x的排放。
分享友人
分享到 Line

分享到臉書