連接結構 的英文怎麼說
中文拼音 [liánjiējiēgòu]
連接結構
英文
linkage structure- 連 : Ⅰ動詞1 (連接) link; join; connect 2 (連累) involve (in trouble); implicate 3 [方言] (縫) ...
- 接 : Ⅰ動詞1 (靠近;接觸) come into contact with; come close to 2 (連接; 使連接) connect; join; put ...
- 結 : 結動詞(長出果實或種子) bear (fruit); form (seed)
- 構 : Ⅰ動詞1 (構造; 組合) construct; form; compose 2 (結成) fabricate; make up 3 (建造; 架屋) bui...
- 連接 : connect; fit together; link; marry; mate; joint; association trail; linkage; concatenate; concate...
- 結構 : 1 (各組成部分的搭配形式) structure; composition; construction; formation; constitution; fabric;...
-
The most commonly used joint configurations are the lap, scarf, and butt joints.
最常用的連接結構是搭接,嵌接和平接。Ambiguity analysis on the basis of junction and nexus
基於連接結構和主謂結構的歧義分析Body / bonnet joints on pacific valves are designed for rugged services with a more than adequate number of bonnet bolts
美國太平洋閥門上的閥體/閥蓋連接結構適用於惡劣的應用環境,可配置足夠數量的閥蓋螺栓。The following conclusions are gained : ( 1 ) the located shear band prongs the ligament near the top crack tip and the structure may occur shear - mode fracture at the angle of 155 ? to crack when load is 87. 92mpa ; the mode of fracture of the flange joint structure is not possible to be void - mode ; ( 2 ) it is proved that loading and then unloading repeatedly can not increase the possibility of invalidation of the structure when the times of loading and unloading are not too more when load is operating pressure ; the structure is safe when the vessel is operating ; ( 3 ) in the fe model of the thesis, not considering the influence of water pressure test which is in the process of fabrication of vessel in fe results in larger deviation in analysi
得出了以下結論:在8792mpa的載荷下筒體一封頭連接結構處的集中剪切帶貫穿韌帶,可能發生沿與原裂紋線成155 「角方向剪切型斷裂;筒體一封頭連接結構不可能發生韌窩型斷裂; ( 2 )在工作壓力下進行次數不多的反復加、卸載,結構不會破壞,也不會喪失安定性:結構在工作狀態下是安全的; m在本文的彈塑性有限元模擬計算中,對于裂紋尖端進行力學分析時,不考慮壓力容器製造過程中水壓試驗的影響,將導致計算結果出現較大的偏差; ( 4 )筒體完全屈服時的載荷為92石3mpa ,封頭完全屈服時載荷為86Coupling dimensions of suspension insulators for high voltage lines
高壓線路懸式絕緣子連接結構和尺寸Finger jointed structural timber - performance requirements and minimum production requirements
指形連接結構木材.性能要求和最低生產要求Acoustics - characterization of sources of structure - borne sound with respect to sound radiation from connected structures - measurement of velocity at the contact points of machinery when resiliently mounted
聲學.關于由連接結構產生噪聲輻射的結構載振動噪聲源的特性描述.機械裝置彈性連接接觸點聲速測量In this dissertation : the advance of the attachment of the metallic tps is reviewed, including the history and development home and abroad and so on
本文內容主要如下:對金屬熱防護系統連接結構的研究現狀進行了分析,包括金屬熱防護系統的發展歷史,國內外研究現狀等。As an important part of metallic tps, the attachment must be strong enough to transfer mechanical load to the substructure and at the same time not much heat quantity
連接結構是金屬熱防護系統的重要的子部件,要求其在傳遞力學載荷同時,不能向機體傳遞過多的熱量,對其研究具有重要意義。16mnr and 45 # steel are taken as examples. the obtained results have been applied to analyze the safety of operation pressure and rationality of design of a kind of engineering structure - a flange joint of hemispherical head to cylindrical shell. try to seek a sort of new method to assessment the capability of structure to load beyond the traditional method which regards stress and strain as main parameters
本文以45 ~ #調質鋼和壓力容器常用鋼材16mnr為研究對象,對金屬材料韌性斷裂的斷裂模式進行細觀機理上的研究,進而分析一種工程結構? ?採用與筒體厚度不同的半球形封頭的壓力容器的筒體連接結構? ?的靜載變形特點和破壞形式,嘗試在以應力應變為主要參數的傳統方法之外,尋求一種新的結構承載能力分析的方法。Construction manufacturing and verification requirement of terminal box flexible connection for explosion proof motor
防爆電機接線盒軟連接結構製造檢驗暫行規定Check ring joint ( crj ) structure was utilized in uspg
卡環式連接結構被應用於水下夾樁器。A ball and socket attachment structure
一種球鉸式連接結構Dual staged cross connect architecture
雙級交叉連接結構Bonnet joint ? joint design varies with ansi class rating
閥蓋連接- ansi壓力等級不同,連接結構也有所不同。Finite element modeling and modal analysis of wedge - ring connection structure
楔環連接結構有限元建模與模態分析Facilities must be captured in the order mandated by the continental lattice
設施必須按照大陸的網格的連接結構來占領。Connecting structure sign
連接結構標記Numerical calculation of damage accumulation and bearing strength experimental verification for composite single bolted joint
復合材料層合板機械連接結構累積損傷模型和擠壓性能試驗研究According to the nonhomogeneous anisotropic elastic theory, a calculation model of composite material plate with circular hole in common structural connection section was developed
摘要針對工程中常見的連接結構中含圓孔的復合材料板,根據非均質各向異性彈性理論建立計算模型。分享友人