邊緣接觸面 的英文怎麼說

中文拼音 [biānyuánjiēchùmiàn]
邊緣接觸面 英文
edge contact area
  • 邊 : 邊Ⅰ名詞1 （幾何圖形上夾成角的直線或圍成多邊形的線段） side; section 2 （邊緣） edge; margin; oute...
  • 緣 : Ⅰ名詞1 （緣故） reason 2 （緣分） predestined relationship 3 （邊） edge; fringe; brink Ⅱ動詞（攀...
  • 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
  • 觸 : Ⅰ動詞1 （接觸） touch; contact 2 （碰; 撞） strike; hit 3 （觸動） touch 4 （感動） move sb ; sti...
  • 面 : Ⅰ名詞1 （頭的前部; 臉） face 2 （物體的表面） surface; top 3 （外露的一層或正面） outside; the ri...
  • 邊緣 : 1 （沿邊的部分） border; edge; fringe; margin; rim; limb; skirt; verge; brink; periphery 2 （靠近...
  • 接觸 : 1. （交往） come into contact with; get in touch with 2. （沖突） engage 3. （挨上; 碰著） contact; touch
  1. In order to make the camber design easier and keep contact pressure equal along rolls, we shall assume the pressure distribution to be quadratic along the width and the marginal deformation to be planar

    摘要為了使中厚板軋機輥型設計快捷且保持輥間各點接觸壓力相等，利用了壓力沿板寬方向呈二次分佈、板邊緣處變形為平面變形的計算處理，從而使輥型設計更為方便。
  2. Detail specification for multi - contact edge socket electrical connectors - single or double sided, closed ended, replaceable contacts, through - board solder or wire wrap terminations - full assessment level

    多觸點邊緣插座電氣連接器詳細規范.單面或雙面閉端可替換觸點穿板焊接或線繞終端.全面評估級
  3. The research about the non - invasive inspection of pcb that is based on ir image is introduced. the detection principle, the components of hardware and software are introduced in this paper. some key technical problems and the project of software are presented in detail : graphics of user interface ( gui ) of the projection, gray scale transformation ( gst ), image contour extraction through edge detection algorithm based on the approaching contour optimization, image registration based on corner detection, the position of hidden trouble pcb through add - minus algorithm image

    本文介紹了利用紅外圖像對印製電路板進行不接觸式故障檢測的系統研究，主要介紹了本系統的檢測原理，硬體組成及軟體的製作，其中詳細地介紹了軟體的製作過程以及其中的幾個關鍵部分：本系統的人機交互界面；圖像的灰度轉換；基於最優輪廓逼近的邊緣提取演算法進行輪廓提取；基於角點檢測的圖像配準；用差影法得到故障電路板的故障隱患或故障部位。
  4. Firstly, a simple and practical representing method of the tooth edge tangential vector is applied to replace the traditional differential formula, the simple solving technique of edge contact problem makes the geometric edge contact analysis of the complex curve surface realize. secondly, using numerical searching and mathematical programming method solves the contact directions and loaded contact problem. finally, whole numerical simulation method is provided for loaded tooth contact analysis of high contact ratio spiral bevel gears

    首先以一種簡單實用的輪齒邊緣切矢量的數學表示方法取代了經典的微分表達式，大大簡化了幾何邊緣接觸的求解，使復雜曲面的幾何邊緣接觸分析得以實現；其次又採用數值搜索與數學規劃法求解了邊緣接觸的主方向和承載接觸問題，為高重合度弧齒錐齒輪承載嚙合全過程的數值模擬提供了完整的方法。
  5. Top tight design requirements of the node, not less than 70 % of close contact, and the gap should not exceed 0. 8 mm greatest risk

    設計要求頂緊的節點，接觸面不應少於70 %緊貼，且邊緣最大間隙不應大於0 . 8 ?
  6. Detail specification for multi - contact edge socket electrical connectors - single or double sided, open ended, guide key location, replaceable contacts, through - board solder or wire wrap terminations - full assessment level

    多觸點邊緣插座插接器詳細規范.單面或雙面開式端導鍵定位可替換觸點穿板焊接或線繞終端.全面評估級
分享友人
分享到 Line

分享到臉書