重磨削 的英文怎麼說

中文拼音 [zhòngmóxiāo]
重磨削 英文
regrinding
  • 重 : 重Ⅰ名詞（重量; 分量） weight Ⅱ動詞（重視） lay [place put] stress on; place value upon; attach im...
  • 磨 : 磨動詞1 （摩擦） rub; wear 2 （研磨） grind; mull; polish 3 （折磨） grind down; wear down [out]:...
  • 削 : 削動詞1. （用刀斜著去掉物體的表層） pare [peel] with a knife 2. （乒乓球的一種打法） cut; chop
  1. This paper mainly aims at the strategic demands for large - aperture lightweight mirror proposed by high - tech development. its main research contents are : select material blank for lightweight mirror according to physical and chemical properties of optical glass ; analyze and calculate the deformation quantity of the mirror with finite element method ; design and optimize mirror body structure of 400 lightweight plane mirror and 450 lightweight spherical mirror, analyze glass cutting principle, design specisl - use grinding wheel structure, select reasonable technological parameters to implement the processing of weight reduction holes on 400 plane mirror ; analyze etching mechanism of hydrofluoric acid, look for the technological parameters such as the optimal acid concentration and etching time etc. ; eliminate the stress of weight reduction holes and micro - cracks on 400 lightweight plane mirror ; discuss the processing principle and

    本論文的研究主要是瞄準國家高技術對大口徑輕型鏡的戰略需求而開展的。主要研究內容是：根據光學玻璃的物理與化學性能，選擇輕型鏡坯材料；用有限元法對鏡子的變形進行分析、計算，找出變形規律，優化設計400mm輕型平面鏡、 450mm輕型球面鏡鏡體結構；分析玻璃切削原理，設計專用磨輪結構，選擇合理工藝技術參數，完成400mm平面鏡輕量化減重孔的加工；分析氫氟酸腐蝕光學玻璃機理，尋找最佳酸濃度、腐蝕作用時間等工藝參數，實現400mm平面鏡減重孔應力與微裂紋的消除；討論分離器加工原理和工藝技術特點，完成400mm平面輕型鏡面形加工。
  2. The product is suitable for double straight line smoothing of grinding flat glass. coarse grinding, fine grinding, and polishing can be done at one time. adopt plc control system, which sets processing parameters via interface, and finishes processing at one time, ti has stable bottom structureprecise and smooth transmission system, the transmission belt drive adopts strong power and tran - sfrequency motor to control speed, constant power, constant rule, output and advanced equipment to control, completed product has high polishing level, which is an ideal option assistant processed equipment of processing delicacy glass and furniture glass factory

    本產品適用於磨削平板玻璃是雙直線平邊，粗磨精磨拋光一次完成採用plc控制系統通過界面設定加工參數次完成加工，具有穩重扎實的底座結構，精確流暢的傳動系繞，傳送皮帶驅動採用功率變頻電機調速控制，恆功率恆扭矩輸出和高配置的控製成品拋光亮度高是加工精品玻璃和傢具玻璃廠家使用的最佳輔助加工設備。
  3. Upgrading of castings to meet x - ray quality needs relies on the grinding out of faulty areas, weld repairs, heat treatment, and retest and examination

    鑄件的改進要滿足x射線質量的要求就要靠缺陷部位的磨削，焊補，熱處理和重復測試和檢驗。
  4. Bonded abrasive products - resin bonded grinding wheel for high - pressure grinding

    普通磨具.樹脂重負荷磨削砂輪
  5. Turning the grinding machine round, driven the barrel body to rotate by the transmission, the work piece that makes in the barrel, grinding stones and adding and grinding pharmaceutical and water in right amount, mix in barrel, is it is it flow layer to produce through action of gravity to make use of, flow friction on layer grind cutting, reach the work piece and process the surface quality taken

    ?轉研磨機，是由傳動帶動桶身旋轉，使桶內的工件、研磨石與添加適量研磨劑和水，在桶內混合，藉由重力作用而產生流動層，進而流動層的磨擦進行研磨切削，達到工件加工所要的表面品質。
  6. 3. the diamond segment wear process was analyzed by testing the weight of segment before and after sawing. the patterns of wear and breakage of diamond grits and bond wear mechanism of the blade were analyzed based on the observation on the working surface of the saw blade by stereo microscope and scanning electronic microscope

    採用稱重法測量鋸切過程鋸片節塊磨損量，並通過計算磨削比，分析了混凝土鋸切過程金剛石節塊的磨損特性及其影響因素，並採用sem和體視顯微鏡觀察節塊不同部位工作表面和金剛石的磨損破壞情況，研究了金剛石磨損破壞的主要形式和胎體材料的磨損形態。
  7. It has many advantages, such as high grinding efficiency, low grinding temperature, high grinding accuracy, low grinding cost, etc

    它具有加工效率高、 「冷態」磨削、磨削速度穩定、磨削精度高、磨削成本低等特點，在機械製造中佔有愈來愈重要的地位。
  8. In this paper, regarding nondestructive testing of surface defects ( for example, grinding - cracks of solid carbide cutting tools etc ), we emphatically analyze post emulsification fluorescence penetrant flaw detection method and application in the field of quantity controlling for solid carbide cutting tools, and we put forward procedure process and procedure parameter of fluorescence penetrant flaw detection for cutting tools

    摘要針對整體硬質合金刀具磨削裂紋等表面缺陷的無損檢測，重點分析和討論了后乳化型熒光滲透探傷法及其在整體硬質合金刀具質量保障技術領域中的應用情況，並確定了刀具的熒光滲透檢測工藝流程和工藝參數。
  9. Abstract : importance of mould grounding of profiled dents is described involving proper selection of equipmets, grounding wheels and grounding specifications for precission and longer life of moulds

    文摘:說明了異形筘片模具刃磨的重要性，應在生產中正確選用設備、砂輪及磨削規范，以便保證模具的精度和壽命。
  10. The paper validates and perfects the traditional wear theory by using the ferrography, at the same time, combining the practice, mechanical embedded minor particles, scoring, plastic distortion, shaping effect and fatigue effect are analyzed and the results show that the vehicle ' s malfunction can be predicted

    文章作者將鐵譜磨粒分析技術運用在汽車維修行業，驗證和完善了傳統磨損理論，並結合實踐，對微凸體機械嵌合、膠合，塑料變形及刨削作用和疲勞作用進行了分析，證明汽車機械故障可以預測，且可以防止重大事故的發生。
  11. For heavy - pressure. form, plunge grinding, snagging of such materials as stainless steel ductile cast iron etc

    適于重磨削、成型磨削、切入磨削及鋼材荒磨，可用於不銹鋼和特種球墨鑄鐵磨削加工。
  12. There exist large stress, intensive scratch, damage and pollution of ion in wafer process, so it is necessary to improve mechanism of slicing and lapping by changing single mechanical function to equilibrium chemical and mechanical function for small damage and low stress. reducing damage and stress and enhancing quality and efficiency of product result in a base of followed process so as to improve wafer process and enhance finished product ratio of whole wafer process

    目前加工過程中存在應力過大，造成表面劃傷嚴重，容易產生破損，離子沾污的問題，因而必須改善切削、研磨機理，把單一的機械作用變為均勻穩定的化學機械作用，以達到淺損傷、低應力的目的，有效的減少破損層和應力的累積，提高產品質量和加工的效率。
  13. The main results are : grinding is favorable to improve surface smooth degree, while nitrided and slow deposition makes sic granules fine ; the width of coatings gap increased in order of grinding, nitrided and vacuum heat treatment, but gap defects in multilayer coatings could be removed by slow deposition ; temperature of maximum weight loss could be decrease to 600 by grinding, vacuum heat treatment or slow deposition, but it will increased to 800 after nitrided ; oxidation kinetics curves all varied with the coating modifications

    主要有：磨削改性有利於提高塗層表面平整度，氮化和慢沉積使塗層表面顆粒細化。塗層間隙寬度按磨削改性、高溫氮化、真空熱處理依次增大，而慢沉積可獲得無面缺陷的多層塗層。磨削改性、真空熱處理及慢沉積均使最大氧化失重溫度點提前至600 ，而高溫氮化則使最大失重點后移至800 。
  14. The bp neural network is applied to the recognition of wear particles, and a bp neural network sorting system expected to recognize severe wear particle, cutting wear particle, normal wear particle and fatigue wear particle is designed and trained. 6. the function of the neural network ' s hidden layer is analyzed

    將神經網路應用於磨粒識別，設計磨粒分類器，在網路學習中運用改進的bp模型，識別嚴重滑動磨損磨粒、切削磨粒、正常磨損磨粒和疲勞點蝕磨粒，隨機選取50個樣本對分類器進行訓練。
  15. Repeatedly grinding, deep and slow movement to reduce overall cost

    4 .可作重磨削深切緩進磨削，降低整體成本。
  16. Emphasis is laid on the importance of the core of ultrahigh speed wheels, design requirement and material selection

    重點強調超高速磨削砂輪基體的重要性和設計要求以及材料的選擇。
  17. Abstract : the practical cad technology to manufacture high accuracy relief grinding cutters is put forward. the methods to improve the cutting performance and regrinding life of the cutters are introduced, and some calculating examples are presented

    文摘:提出了方便快捷地加工高精度鏟磨刀具的cad實用工藝，給出了改善刀具切削性能和增加重磨極限（壽命）的方法及計算實例。
  18. Z1 ( tan ) : heavy media for fast cutting and good wear designed to produce excellent finished with reduced cycle times

    Z1 （褐色） ：很重的磨塊，很好的切削，適合的磨損，在短時間內獲得理想的表面。
  19. Under the support of jiangsu province key scientific and technological project, this dissertation does research on nc code preprocess and solid - based verification simulation in noncircular surface nc grinding

    本文以江蘇省科技攻關項目為依託，著重對非圓曲面數控磨削加工模擬中的數控代碼預處理技術和基於實體的模擬驗證技術開展了研究。
  20. In this paper, a cutting experiment using metal cutting tools with frictional reducing groove is described. the calculation and analysis of measured cutting force data shows that this kind of cutting tools can reduce the data of cutting force. and according to these, the relations among frictional reducing groove parameters and other parameters such as feed engagement were analyzed. cutting tools with frictional reducing groove have practical value when great cutting depth and feed engagement are needed because the cutting force is reduced obviously. frictional reducing groove has wide prospect in the use of non - regrinding tools

    通過採用磨有減摩槽的車刀進行切削實驗，將測得的切削力數據計算分析得出磨有減摩槽的刀具可降低切削力的數據，並由此分析減摩槽參數與進給量等參數之間的關系.磨有減摩槽的刀具在大切削深度、大進給量的切削加工方面有明顯的降低切削力的效果和實用價值，用於不重磨刀片刀具上具有廣闊的前景
分享友人
分享到 Line

分享到臉書