長瞬態效應 的英文怎麼說

中文拼音 [zhǎngshùntàixiàoyīng]
長瞬態效應 英文
long-transient effect
  • 長 : 長Ⅰ形容詞1 （年紀較大） older; elder; senior 2 （排行最大） eldest; oldest Ⅱ名詞（領導人） chief;...
  • 瞬 : Ⅰ名詞（眼珠一動; 一眨眼） wink; twinkling Ⅱ動詞（眨眼） wink
  • 態 : 名詞1. （形狀; 狀態） form; condition; appearance 2. [物理學] （物質結構的狀態或階段） state 3. [語言學] （一種語法范疇） voice
  • 效 : Ⅰ名詞（效果; 功用） effect; efficiency; result Ⅱ動詞1 （仿效） imitate; follow the example of 2 ...
  • 應 : 應動詞1 （回答） answer; respond to; echo 2 （滿足要求） comply with; grant 3 （順應; 適應） suit...
  • 瞬態 : transient; instantaneous condition; transient state
  • 效應 : [物理學] effect; action; influence
  1. Linear induction motor is an important kind of machines which have some merits such as simple structure, low cost, durability, convenience for maintenance etc. the subject of this thesis is to study a big circular ring linear induction motor, and the major works in this thesis are summarized as follows : ( 1 ) considering the effects of the finite length of primary core, one - dimension analytical solution for the air gap field is cited in this paper. based on it, the single layer winding magnetic field is studied. considering whole - pitched and short - pitched winding configuration with odd poles and half - fulled slots in both ends, the double - layer winding magnetic field is analyzed, respectively

    本文對大圓環直線感應電機進行了深入細致研究，內容包括： （ 1 ）本文採用有限長行波面電流作用於有限長鐵芯上的模型，引用了氣隙磁場一維解，研究了單層繞組磁場，奇數極半填槽雙層繞組在採用整距和短距時磁場的分析、比較，簡單介紹了二維解； （ 2 ）用有限元軟體ansoft對大圓環直線感應電機空載氣隙磁場進行了靜態分析，並分析了結果； （ 3 ）用軟體進行了額定電壓下的瞬態分析，得到了轉矩，位移，轉速隨時間變化曲線圖，利用單極性霍爾元件測定轉速並與軟體計算結果進行了比較，採用等效電路法計算了堵轉時的最大電磁力並做實驗進行了驗證，由實驗測得了三相電流波形，並與計算結果進行了比較，對其不對稱性進行了定性分析。
  2. The explicit finite element method ( fem ) based on the varying time - step was selected to analyse the dynamic roll - pass process ; the nodes on the leading face of the steady - state elements set was extracted and projected onto a plane to give the required mesh, also called the origin mesh ; the implicit fem was selected to analyses the inter - pass transient thermal process ; a geometric part from the mesh was generated and meshed by using the quadrilateral elements, a heat transfer analysis was selected to transfer the node temperature data ; a new model was created by using hexahedral elements, mapping the node temperature and the equivalent plastic strain on the integration points

    利用基於變步長中心差分格式的顯式積分方法分析瞬態軋制過程；提取穩態單元集節點形成截面網格；利用隱式積分方法分析軋制道次間隙瞬態溫度場；對型鋼斷面進行平面四邊形網格劃分並映射節點溫度數據；利用六面體單元構建有限元分析模型，映射單元節點的溫度、積分點的等效塑性應變，進行數值分析。
分享友人
分享到 Line

分享到臉書