閥傳動機構 的英文怎麼說

中文拼音 [fázhuàndòngjīgòu]
閥傳動機構 英文
valve driving mechanism
  • 閥 : 名詞1 （指在某方面有支配勢力的人物或家族） established house or power group; a powerful person or...
  • 傳 : 傳名詞1 （解釋經文的著作） commentaries on classics 2 （傳記） biography 3 （敘述歷史故事的作品）...
  • 機 : machineengine
  • 構 : Ⅰ動詞1 （構造; 組合） construct; form; compose 2 （結成） fabricate; make up 3 （建造; 架屋） bui...
  • 機構 : 1 [機械工程] （機械的內部構造或一個單元） mechanism 2 （機關; 團體） organ; organization; institu...
  1. Analysis is made on structure characteristics of the finned - tube, and analysis has been made on the special heat and mass transfer principle of every micro - unit under both dry and wet conditions. appropriate hypothesis is made and based on the energy, mass and momentum equivalent, the evaporator models of dynamic distributed parameters are set up. in addition, the gascooler and internal exchanger models of dynamic and distributed parameters, the throttling valve models and the compressor models are set up, too

    本文的內容如下： 1對翅片管蒸發器的結構特點進行分析，選取適當的微元體，對于干、濕工況下每個微元分別進行傳熱傳質分析，通過適當的假設，利用質量守恆方程、能量守恆方程和動量守恆方程建立了蒸發器的分佈參數數學模型；對回熱器劃分微元建立了分佈參數數學模型；對氣體冷卻器建立了分佈參數數學模型；對壓縮機建立了數學模型；建立了節流閥的數學模型，為系統模擬奠定了基礎。
  2. Comparing and analyzing the synchronous control strategy, which brings up the new method to control the double un - symmetry jars proceed synchronously with the combination of proportional valve and servo valve, which forms closed loop control ; basing on the above methods, models are made to get mathematics models of position control system and to analyze system model theoretically by using pid controller, we can realize regulating parameters, minimizing synchronous errors and enhancing the dynamic performances ; the simulink tool box in matlab software is used to imitate the system according to the model, which not only makes the result visual and easy to adjust the parameters in interactive way but also lets us understand the effects of different parameters and optimizes the dynamic properties. the theory of plc control in dshp is discussed after advanced understanding of the system movements. hardware design and general regulation are given on the base of siemens company products s7 - 200 plc

    本文根據大量的國內外文獻，對研配液壓機的工作原理及設計結構進行了簡介；對位置同步的控制方法進行了比較分析，提出比例閥和伺服閥復合控制的閉環結構來對非對稱雙缸進行同步控制電液比例同步控制方案；在此基礎上著重對比例閥控非對稱缸建模，最後得到位置控制系統的總體數學模型，從理論上對同步系統動態特性進行了分析，並用pid控制器進行參數整定，減小雙缸同步誤差、提高系統的動態響應性能；其中控制性能的分析藉助于matlab軟體中的simulink工具箱，由已建立的數學模型形成模擬模型，得到可視化的模擬結果，從而利於交互方式下調整參數，了解不同的參數對系統的影響，優化同步系統的動態性能；在深入了解系統的動作特性后，對plc控制研配液壓機的原理進行了探討，針對siemens公司s7 ? 200型plc給出了硬體設計的總體規劃，編制出研配液壓機動作控製程序，在編程中著重研究位移傳感器與plc的通訊、雙缸同步運行的pid控制在plc上的實現及bcd碼撥盤輸入程序的植入問題。
  3. Valve driving mechanism

    閥傳動機構
  4. Valve - actuating mechanism

    閥門傳動機構
  5. Industrial valves. actuator. technical check list form

    工業閥門.傳動機構.技術檢查清單表格
  6. Control valve actuator

    閥控傳動機構
  7. The robot controller adopts a kind of two - level structure. the top level was the host controller and motor driver, the main program and motor servo arithmetic program running in it, and also receive command from the remote computer. the lowest level was two sensing system, fixing on foot of the robot, gathering and processing information from multi - kind sensors, and also controlled the pump and valve

    機器人嵌入式控制器採用兩層結構，上層為機器人主控及驅動電路，負責運行機器人主控程序及多電機伺服控制演算法，以及接收上位計算機的遠程遙控命令;下層為兩個足部傳感系統模塊，分別安裝在機器人的兩個足上，負責多種傳感器信息的採集、處理及泵和閥的驅動控制。
  8. Components and systems of reciprocating internal combustion engines - glossary of terms for valves, camshaft drive and actuating mechanisms

    往復式內燃機部件和系統.第3部分:閥門凸輸軸傳動和驅動機構的術語詞匯
分享友人
分享到 Line

分享到臉書