閥桿手柄 的英文怎麼說
中文拼音 [fágǎnshǒubǐng]
閥桿手柄
英文
handle for valve stem-
For applications requiring handle removal, the d - ring stem flats indicate “ open / close ” and a molded - in arrow on top of the stem indicates flow direction
由於實際應用中可能需要拆卸手柄,因此d形環閥桿平面表示「啟閉」 ,閥桿頂部的的模鑄箭頭表示流向。In reassembly of lever handle, align the index plate so that the number one ( 1 ), indicating the full closed * position, is at right angles to the bore of the valve
在組裝杠桿手柄時,對準刻度板,使其指示全閉位置的數字1位於閥門閥腔上的準確位置。Standing clear of the outlet ( discharged water may be hot ), slowly lift and release the lever handle on the temperature and pressure relief valve to allow the valve to operate freely and return to its closed position
經常清洗出口(排泄水可能是熱的) ,慢慢提起並釋放降溫減壓安全閥上的杠桿手柄,使得閥門能夠靈活工作並恢復到關閉位置。Double d stem configuration : gives positive attachment for handles or actuators
雙d閥桿結構:非常適用於連接操作手柄或執行機構。The shaft also shall have a directional indicator on top to indicate disc position when the handle is removed
閥桿也應該在頂部配置方向指示器,用於當手柄拆卸下來時指示閥瓣的位置。Make sure the diaphragm tab and compressor guides are properly located in their body slots by rotating the handle counterclockwise until the stem is in the full up position
通過逆時針方向旋轉手柄,直到閥桿位於完全上升的位置,確保隔膜接頭片和壓縮裝置導架位於閥體上的相應的槽上。If necessary, the stem and stem seal may be removed from the bonnet by removing the retainer ring and handle and screwing the stem out the under - side of the bonnet
如果必要的話,閥桿和閥桿密封可能要從閥帽上拆卸下來,要在閥帽的下方先拆卸擋圈和手柄,以及閥座上的螺絲。Ball valve design includes reinforced / enhanced ptfe seats and electroless nickel plated brass ball, blow - out proof pressure retaining stem, and low profile oval handle
球閥結構包括強化聚四氟乙烯( ptfe )閥座和非電解鎳鍍層黃銅球體,防吹出壓力保持閥桿,以及低矮型橢圓手柄。As shown on the schematic drawing on the right, the closing member ( stem and disc assembly ) of the figure 85 or 90m frostproof sillcock operates by turning the handle in a clockwise manner to close and counter - clockwise to open
正如右側示意圖所示,型號85或90m防凍灑水龍頭上最靠近的部件(閥桿和閥瓣總成) ,是通過順時針方向旋轉手柄來實現旋轉關閉和逆時針方向旋轉開啟。In the process of use and repair, before the confirmation of reliable connection of valve stem and handle, tooth disk or drive head and other parts, the valve can not access to medium to bear pressure, otherwise the valve stem may dash out, causes dangerous accidents
使用或維修過程中,在閥桿與手柄、齒盤或傳動頭等部件確認可靠連接前,閥門不能通入介質承壓,否則可能使閥桿沖出,造成危險事故。分享友人