閥簧座 的英文怎麼說

中文拼音 [fáhuángzuò]
閥簧座 英文
valve spring cup
  • 閥 : 名詞1 （指在某方面有支配勢力的人物或家族） established house or power group; a powerful person or...
  • 簧 : 名詞1. [音樂] （樂器里能發聲的薄片） reed2. （器物上有彈力的機件） spring
  1. The parallel seat gate assembly consists of two interchangeable spring loaded discs, a fully guided disc carrier, and retaining pins

    平行閥座閘閥由兩個可互換彈簧負載閥瓣，一個全導向閥瓣托架和扣環銷釘構成。
  2. Series 415 steam safety valves feature a stainless steel spring, a top guided stem and non - stick teflon ? disc to metal seating to assure positive shutoff

    系列415蒸汽安全閥配置不銹鋼彈簧，一個頂部引導閥桿和不卡住特氟隆閥瓣對金屬閥座密封，確保絕對關閉。
  3. Because expansion valves are high precision processing components, factory in its internal adjustment of the body parts are processed in a state of complete thermostatic, the temperature of the gas filling kits are demanding more consistent not detect leaks, in the completion of the expansion valve assembly also undergo strict testing and fatigue resistance aging sampling, the construction expansion valves : 1 : indeed temperature temperature kits ; 2 : temperature gas or liquid filled with the expansion corrugated ; 3 : spherical valve seat ; 4 spherical valves ; 5 : spring ; 6 : overheating degrees adjustment screw spacer and screw ; 7 : internal and external ( h - type ) sealed pieces ; 8 : thrust poles and corrugated of spacer ; 9 : fati ; 10 : capillary, and so on

    因為膨脹閥是屬于超高精密加工的零件，在工廠對其內部調整機構零件的加工都在恆溫狀態下完成，其中的感溫包的氣體充填更是要求嚴格一致不允許一絲泄漏，在完成裝配的膨脹閥還要經過嚴格的測試和耐疲勞老化抽檢，膨脹閥的構造： 1 ：感知溫度的感溫包； 2 ：感溫氣體或者液體充填膨脹波紋腔； 3 ：球型閥座； 4球型閥； 5 ：彈簧； 6 ：過熱度調整螺絲墊片和螺絲； 7 ：內部和外部（ h型）密封件； 8 ：推力桿和波紋腔墊片； 9 ：閥體； 10 ：毛細管等等。
  4. The greatest feature of this valve is that the ability to take advantage of pipelines within the medium pressure promote hemisphere, therefore, its sudden opening and closing power is stronger than any other type, with such advantages of no friction, no wearing and long life of use

    該閥的最大特點是能藉助管線內的介質壓力推動半球，所以它瞬間啟閉力比任何一類球閥都輕快的多，同時在同步連桿和拉簧的作用下，使兩半球離開閥座密封面，然後再旋轉球體，閥門的啟閉過程中有密封面無磨擦、無磨損、使用壽命長等優點。
  5. To avoid this discharge, install a spring - loaded, rubber seated check valve ahead of the backflow assembly

    為了避免這種排放，要在防迴流閥總成前面安裝一個彈簧驅動、橡膠閥座的止回閥。
  6. To replace seat disc or diaphragm loosen locknut ( 51 ) and back off adjusting screw ( 53 ), remove four bonnet screws ( 24 ) and lift off cage ( 3 ) with spring ( 729 ) and washer ( 61 )

    要更換閥座閥瓣或隔膜，則松開鎖緊螺母（ 51 ）並退出調節螺絲（ 53 ） ，拆卸四個閥蓋螺絲（ 24 ）並將帶著彈簧（ 729 ）和墊圈（ 61 ）的籠（ 3 ） 。
  7. Holding the check valve module in both hands, rotate the assembly quarter turn. this will disengage the disc assembly, spring and seat cover into individual components

    雙手握住止回閥模塊，將總成旋轉四分之一轉。這將把閥瓣總成、彈簧和閥座蓋分解成獨立的部件。
  8. Note : the seats and springs of the first and second check modules are not interchangeable

    注：第一和第二止回閥模塊的閥座和彈簧是不能互換的。
  9. The assembly shall consist of two threaded - in check modules with captured springs and silicone seat discs

    這種總成應該由兩個螺紋旋進、配置復位彈簧和硅酮閥座閥瓣的止回閥模塊構成。
  10. Air valve is made up of upper valve seat, lower valve seat, 5 kinds of accurate valve slice and 25 springs

    該氣閥是由上閥座、下閥座及大小5種精密閥片和25個彈簧等零件組成。
  11. To clean ; remove bottom plug, seat spring, strainer and seat disc

    因此要清洗，拆卸底部塞、閥座彈簧、過濾器和閥座閥瓣。
分享友人
分享到 Line

分享到臉書