階梯分型面 的英文怎麼說

中文拼音 [jiētīfēnxíngmiàn]
階梯分型面 英文
stepped joint stepped sprting
  • 階 : 名詞1. （臺階） steps; stairs 2. （等級） rank 3. [醫學] （耳蝸的三個螺旋管的任一個） scala 4. [數學] order 5. [地質學] stage
  • 梯 : Ⅰ名詞1 （梯子; 樓梯） ladder; stairs; steps; staircase 2 （姓氏） a surname Ⅱ形容詞（形狀像樓梯的...
  • 分 : 分Ⅰ名詞1. （成分） component 2. （職責和權利的限度） what is within one's duty or rights Ⅱ同 「份」Ⅲ動詞[書面語] （料想） judge
  • 面 : Ⅰ名詞1 （頭的前部; 臉） face 2 （物體的表面） surface; top 3 （外露的一層或正面） outside; the ri...
  • 階梯 : （臺階和梯子, 比喻向上的憑借和途徑） a flight of stairs; ladder; staircase; step
  1. The typical velocity field and the pressure on the step surface of the stepped spillway are measured using the laser doppler anemometer and the piezometer tube respectively

    採用多普勒激光測速儀和測壓管分別對階梯溢流壩面典型速度場和階梯表面壓力進行詳細測量。
  2. As the basis of stochastic torsional analysis, a stepped thin - walled beam model with complex cross - sections of arbitrary shapes ( open, closed or mixed ) is established in this paper, which takes into account the effect of secondary shear flow resulting from warping restraint

    摘要具有復雜斷面形狀的階梯精密梁模型作為扭轉隨機分析的基礎，可以計及翹曲約束引起的二次剪流。
  3. The finite element analysis of ladder horns with rectangular cross - section based on ansys

    的矩形截面階梯型變幅桿有限元分析
  4. The surface ladder effect produced by prototyping principle is analyzed, and the calculation method of the part surface roughness is presented. the selecting method of slice thickness and sintering layer thickness when slicing the cad model and sintering is presented

    分析了由於成型原理所產生的製件表面階梯效應，提出了製件表面粗糙度的計算方法，給出了cad模型切片時，切片厚度的選取方法。
  5. The second chapter of the thesis discuss emphatically the development, algorithm, remarks and present problems of dmrg. besides, we try to add odd or even sites to the rung of a two - leg coupled spin ladder, and to calculate the energy and spin gap of the class of models

    第二章主要講述了dmrg的發展、方法步驟、應用評價，目前所面臨的問題，並嘗試在兩條耦合海森堡鏈的階梯模型的「橫檔」上分別加入奇數、偶數今格點。
  6. The main thrust of this study are follows : the primary study provides in detail the area structural properties including the fault systems, structure units, and trap types ; the secondary study including the sedimentary systems including stratigraphic classifications, depositional environment properties, infilling - evolution properties, and oil source analysis ; the third area of study including the geologic property of the north slope zone ; and the final area of study provides an analysis of gas and oil accumulation, the types and distribution of reservoirs, and the pool - forming models used

    本研究主要從事了以下工作，較為詳細地研究了該地區斷裂體系、構造單元、圈閉類型等構造特徵；從地層劃分、沉積特徵、沉積環境、充填演化特徵、油源分析等方面研究了該地區的沉積體系；詳細地研究了油氣資源豐富的北部緩坡階梯帶的地質特徵；根據成藏動力學系統理論，較為詳細地研究了該區的油氣運聚模式、油氣藏類型及油氣藏分佈規律。
  7. Abstract : the tolerance and generation of the stair - error in rp were studied. by using the normal vector information of the tringon facets in stl file, a calaculating method of stair - error was proposed and a slice - adapt algorithm which will save the time of mold manufacturing was presented

    文摘:研究了快速成型過程中階梯誤差的產生與度量，並利用stl文件中的三角形面片的法矢量信息給出了階梯誤差的計算方法，提出了可變分層厚度的演算法，採用自適應分層來減少成型時間的方案
分享友人
分享到 Line

分享到臉書