集電極電壓 的英文怎麼說
中文拼音 [jídiànjídiànyā]
集電極電壓
英文
collector voltage-
The products we mainly dealt in include all types of ceramic capacitor, aluminum electrolytic capacitor, zinc oxide varistor, integrated circuitries, and diodes
公司所經營的產品包括種陶瓷電容器、鋁電解電容、壓/熱敏電阻、集成電路、二極體等。First, passive resistance network was selected as direct current biasing network, which offered direct voltage for base through the resistance voltage divider composed of two resistances, among them the upper resistance connected from the dc to base, the lower resistance connected from the base to ground. the collector connected with dc directly
直流偏置網路採用無源電阻網路,通過由兩個電阻組成的電阻分壓器為基極提供直流電壓,上偏電阻從電源串聯到基極,下偏電阻從基極到地,集電極直接加電。A lot of experiments have been done in the process of exploiture soft packaging li - ion battery about how to choice the rational arts and crafts. the content include : how to deal with the collector, add how much pvdf in the material, how long the material need to stirring and the right viscidity, how much condubtivity agent the electrode need, what theckness is best, choice different collectors, the degree of dryness of the electrode, theckness of pressed model, how much electrolyte will be added, placement how long after added the electrolyte, system of formation how to influnce the battery, in formation the battery need or not need preesure from outside, how to vacuumize and the optimize matching positive pole and negative pole. with these practice make sure the parameter of the positive pole should less than 90 m ; according to different vacuumize order the conduc - tivity agent in anode will be 5mass % and 9mass %, respectively, and in cathode the data is 2mass % ; every 100mah added to 0. 4 ml electrolyte ; before formation the battery should be placement 8 hours and the system of formation must be less than 0. 01c before the voltage reach to 3. 0v ; should press in outside when battery in formation ; to these batteries which capacity more than 350mah the vacuum time not excess 15s ; the optimize matching positive pole and negative pole between 2. 10 : 1 and 2. 15 : 1. finally make out the battery which cycling performance and security are all very well
液態軟包裝鋰離子電池的研究主要是對關鍵工藝進行了優化設計,具體包括:集流體的處理、 pvdf的加入量、漿料攪拌時間和粘度、導電劑的加入量、電極膜的厚度、不同集流體的選擇、電極膜的乾燥程度、壓型的厚度、電解液的加入量、注入電解液后靜置時間的長短、化成制度的影響、化成時電池所具有的壓力影響、抽真空的處理、正負極活性物質的匹配。最後確定出液態軟包裝鋰離子電池最佳工藝參數:正極膜的厚度小於90 m ;根據化成時不同抽真空順序,確定正極膜中的導電劑的加入量分別為5mass %和9mass % ;負極膜中導電劑的加入量為2mass % ;電解液的加入量為每100mah添加0 . 4ml ;化成前電池的靜置時間應當大於8h ;電池在3 . 0v之前採用小於0 . 01c的化成制度;在化成過程中應當施加一定的外部壓力;對於350mah的電池抽真空的延時不應大於15s ;而正負極活性物質的質量比應當在2 . 1 : 1 2 . 15 : 1之間。The instrument is integrated with a multi - channel high precision open circuit potential measurement system for the ion selective electrode and a potentiostat used in voltammetry, an analog lock - in amplifier is also presented to measure the response of light addressable potential sensor
對于不同的測量技術,儀器中集成了用於測量電極的多通道高精度開路電壓測量系統和用於溶出伏安法測量的多路電化學測量系統,以及用於測量光尋址電位傳感器的鎖相放大器。Modern voltage references are constructed using the energy - band - gap voltage of integrated transistors, buried zener diodes, and junction field - effect transistors
現代電壓基準建立於使用集成晶體管和帶狀能隙基準、掩埋齊納二極體和結場效應晶體管。A novel low mechanical hysteretic ceramic capacitive pressure transducer has been made, by using of ceramic sealing technology ; integrate circuit ( ic ) technology and thick film plane fixing circuit technology. this transducer is made of a deformable ceramic diaphragm and a ceramic base plate, between which has an air cavum. a coaxial gold electrode was fired onto the diaphragm and the base plate
本文利用新型陶瓷技術、集成電路技術和厚膜平面安裝電路技術,採用零力學滯后的陶瓷和陶瓷密封材料進行設計製造了一種非充液乾式的電容式壓力傳感器,該壓力傳感器由較厚的陶瓷基體和較薄的陶瓷膜片構成,中間形成一空氣介質腔,在基座和膜片之間內置同軸的雙電極,組成兩個電容,當膜片承受壓力時發生位移,使電容量產生變化,經後置處理電路直接轉換為可輸出的直流電壓信號。The optimum conditions for air electrode preparation were shown as follow : 20 % ptfe and 20 % mno2 in active layer, thickness of active layer 0. 15 - 0. 25mm and the ratio of active carbon to ethine black 4 : 1 ; 60 % ptfe in the gas diffusion and waterproof layer, employing na2so4 as pore - making agents, thickness 0. 35 - 0. 45mm, colding forming and layer sequence catlytic layer / gas diffusion and waterproof layer / current collector layout ; employing 40 meshed nickel screen as current collector and thermal treatment temperature over 200
確定了制備空氣電極的優化工藝條件,催化層中ptfe含量約20 , mno _ 2的最佳含量約為20 ,催化層中活性炭和乙炔黑的比例為4 : 1 (質量比) ,厚度在0 . 15 - 0 . 25mm之間。防水透氣層中ptfe的含量約為60 ,以無水硫酸鈉作為造孔劑,厚度一般為0 . 35 - 0 . 45mm 。電極各層採用催化層/防水透氣層/集流體的排布方式,冷壓成型,熱處理對空氣電極的性能影響較大,熱處理溫度不低於200 。When the flue gas and dust past through electrical fields, they caused impact with positive and negative ion and electron between electrical electrodes to charge electric. the charged particles move and are accumulated to difficult electrical electrode due to effect of electric field force. through rapping method, the dust leaves electric electrodes and drop into the collection hopper, and the remove the dust by transportation system
是一種煙氣凈化設備,它的工作原理是:煙氣中灰塵塵粒通過高壓靜電場時,與電極間的正負離子和電子發生碰撞而荷電或在離子擴散運動中荷電,帶上電子和離子的塵粒在電場力的作用下向異性電極運動並積附在異性電極上,通過振打等方式使電極上的灰塵落入收集灰斗中,使通過電除塵器的煙氣得到凈化,達到保護大氣,保護環境的目的。The signal sampling circuit fulfill the tasks of sampling signal and changing the double polarities signal to the single polarity signal ; the drive circuit receives the pwm signals from dsp and pass the signals to ipm through optical - couple devices ; the protective circuit safeguard the system against high current, high voltage, low voltage and high temperature on the ipm model
其中信號處理電路主要完成採集輸出電流和中間直流環節電壓信號,並對採集到的電流信號進行極性變換處理的功能;驅動電路接收dsp輸出的高頻驅動信號,通過耦合器件直接驅動ipm模塊;保護電路利用採集到電氣信號對整個系統實施保護,包括過電流、過電壓、欠電壓、 ipm模塊過熱等。The results of simulations are : i ) energies of the incident ions to the target are determined mainly by the voltage across the cathode sheath, with a majority of ions " energy vary around the sheath voltage ; ions nearly normally bombard the target ; ions mainly locate above the sputtering holes because of the influence of the magnetic field, and the incident ions mainly come from the region ; the ions undergo several collisions during transportation, but that do n ' t matter much
主要模擬結果有: ? )入射離子到達靶面時的能量主要受到了射頻輝光放電中陰極殼層西北工業大學碩士學位論文李陽平電壓的影響,大部分離子的入射能量在陰極殼層電壓值附近,離子濺射時接近於垂直入射;射頻輝光放電受到陰極磁場的影響,等離子體中的離子主要集中在靶面濺射坑的上方,且入射離子主要來自這個區域;入射離子在輸運過程中和背景氣體分子有少量的碰撞,但影響不太大。Features : low vce ( sat ), large current capacity
特點:集電極-發射極飽和壓降低,電流大。Integrated circuits require less power and lower voltages than the equivalent macroscopic circuits, consequently they operate at lower temperatures, and individual components may be closed together without exceeding the operating temperature limit
參考譯文:集成電路比等效的分離元件電路功率小,工作電壓低,因而可以在較低的溫度下工作,電路中包含的單個元件可以緊靠在一起而不超過工作溫度極限。For low distortion, the drains ( or collectors ) of a differential amp " s front - end should be bootstrapped to the source ( or emitter ) so that the voltages on the part are not modulated by the input signal
為了得到低失真,差分放大器前端的漏極(或集電極)應該被引導到源極(或射極) ,這樣埠電壓就不會被輸入信號調制了。The power supply module is made of sg3525a, which supply current for pipeline cp. the data collection module is made up of single chip, which collect the nature eroding voltage, protection voltage and current on the spot and transport these data to pc by com. pc constitutes master control module, which inspects work state of the whole cp system, control the system start and exit, display data out of the single chip
本系統採用sg3525a晶元構成開關電源模塊,提供管線陰極保護電流;採用單片機系統做為數據採集模塊,採集管線現場自然腐蝕電位、保護電位、保護電流等數據,並把採集的數據通過串列口送往pc機; pc機為主控模塊監控整個電源系統的工作狀態,控制整個模塊的投入和退出,完成人機對話;利用顯示器顯示系統輸出電壓、電流。Well, the ratio works similarly : if emitter current is held constant, collector current will remain at a stable, regulated value so long as the transistor has enough collector - to - emitter voltage drop to maintain it in its active mode
系數的作用與之類似:如果發射極電流保持恆定,只要集電極發射極電壓足以使其保持在放大區,集電極電流也將穩定保持。They are as follows : powder types, electrode voltage and board space etc. and the optimized parameters obtained in the normal temperature spray experiments were applied in the thermal spray
通過冷噴實驗,找到了影響收集西安理工大學碩士學位論文效率的因素有:粉末類型、電極電壓以及極板間距等。並將冷噴時的最佳參數應用於熱噴塗制粉末的收集中。The high density resisitivity method through electrode power supply, surveys electric current and voltage, gathers apparent resistivity data
摘要高密度電法通過電極供電、測量電流和電壓,採集視電阻率數據。The hybrid claw - pole alternators have magnetic fields contributed by permanent magnet as well as excitation coil, and the advantages are high efficiency, have good low - speed characteristics, excitation adjustable and high flux densities. for the reason of complex claw - pole construction and 3 - d magnetic field distributions, there is lack of the research on the alternators
混合勵磁爪極發電機是由永磁體和勵磁線圈共同產生電機磁場的一種發電機,與傳統的爪極發電機相比有高效、低速性能好和集線圈勵磁的電壓調節性能與高磁通密度的優點,具有很好的研究前景和使用價值。We have done the following work in this paper : 1. proposal of a novel high - voltage soi lateral structure ( tsoi ), and establishment of its blocking theory ; 2. proposal of devices based on epitaxial simox soi ( esoi ) substrate ; 3
本文主要進行了三個方面的工作: 1 、提出了降場電極u形漂移區的橫向高壓器件結構tsoi ( trenchsoi ) ,並建立了該結構的解析理論[ 1 ] ; 2 、提出基於simox外延襯底esoi ( epitaxialsimoxsoi )的器件結構; 3 、設計了基於simox處延襯底結構的功率開關集成電路。The structure of field emission triode is first simulated by magic. the tip height, tip position, tip curvature, gate aperture, and gate voltage are changed, to observe the emission current and the electron congregation
本課題首先採用magic軟體對三極體結構的尖錐場發射陰極進行了模擬計算,分別改變尖錐高度,錐尖位置,尖錐曲率半徑,柵極孔徑及柵極電壓,觀察陽極收集電流及電子束的會聚情況。分享友人