零標度線 的英文怎麼說
中文拼音 [língbiāodùxiàn]
零標度線
英文
zero scale mark-
Bearings roller bearings and other components. bearing ring precision rolling production line ; a high - precision, super efficient grinding automatic production line ; bearing assembly line ; signal processing equipment ; blank processing equipment ; crowning roller grinder ; end - grinder ; coordinate precision grinder ;, cylindrical grinder ; surface grinder ; spherical roller processing equipment ; raceway grinder ; heat treatment ; needle processing equipment ; polishing processing equipment ; roller - seiki ; rolling auto - sorting machine parts bearing hardness sorting machine bearing cleaning equipment ; contact angle measuring instrument ; contour meter ; bearing life experimental device ; bearing packaging equipment ; roundness instrument ; dynamic vibration noise analyzer ; noise vibration test equipment ; printing machine measuring instrument ; roughness tester ; scanning electron microscope ; finish detector ; inverter ; spindle, wheel, whetstone and other grinding materials
軸承套圈精密輾擴生產線高精高效磨超自動生產線軸承自動裝配線球加工設備毛坯加工設備凸度滾子磨床雙端面磨床高精度坐標磨床內外圓磨床平面磨床球面滾子加工設備溝道磨床熱處理生產滾針加工設備光飾加工設備滾道超精機滾動體自動分選機軸承零件硬度選別機軸承清洗設備角接觸測量儀輪廓測量儀軸承壽命實驗裝置軸承包裝設備圓度儀振動噪音動態分析儀振動噪音測試裝置印字機加工測量儀粗糙度測試儀掃描電子顯微鏡光潔度檢測儀變頻器電主軸砂輪油石和其他研磨材料In this paper, optic gyro is viewed as the object of investigation and several aspects is investigated as follows. two important indexes - bias instability and scale factor were measured and investigated, including bias, its repetitiveness, temperature sensitivity, random walk coefficient and scale factor, its nonlinearity, asymmetry, repetitiveness. we make use of the allan variance method to separate the noise factors which affect the performance of the optic gyro, such as the angle random walk, bias instability, rate random walk, rate ramp, quantization noise, markov noise and sinusoidal noise
本文以光學陀螺為研究對象，開展了以下幾方面的研究工作：本文對光學陀螺性能的兩個重要指標?標度因數和零偏穩定性進行了較為詳細的研究，其中包括陀螺的零偏b _ 0 、零偏重復性b _ r 、零偏溫度靈敏度b _ t 、隨機遊走系數rwc和標度因數k 、標度因數的非線性k _ n 、標度因數不對稱性k _ h 、標度因數重復性k _ r等等。Abstract : it proposes a model for shaft centerline measurement and winding level, gives the coordinates transformation formula of measured data, and develops the program diagram for centerline measurement of wind - shaft
文摘:提出了一種便於微機處理的軸線的空間解析表達方法以及軸線彎曲程度的表示方法，給出了軸線測量數據獲取方法與坐標轉換公式，提出了零件軸線彎曲時精密測量的一般步驟。With the rapid development of manufacture automation, quite likely to become the next generation of cmm, intelligent cmm is the kind of cmm that can finish measuring work automatically and guide the cnc modify the program
隨著製造業自動化程度的提高，智能化三坐標測量機將成為未來的發展方向。智能化三坐標測量機能根據被檢測零件cad信息自動完成在線測量，並指導加工中心改進零件加工程序，整個過程人為干預大大減少。Aees employs the multi - staged digital filter algorithm to reduce random error. meanwile, the system correct zero deviation through linear opreation. the instrument, from hardware aspect increases the feature of anti - interference by the way of reasonable layout, sepration of digital and analogue
系統採用了中值濾波和滑動平均濾波相結合的多級數字濾波演算法來減小隨機誤差，並以精密基準電壓作為比較信號的輸入，由智能系統通過線性運算，實時地修正、校準測量數據，減小系統的零漂，實現自動定標並提高測量的精度。Standard of moulding is typical tamiya with very clean and crisp details with no flash and just the bare minimum of pin marks to be removed and the usual fine moulding seams which will require care on the smaller parts
模型的標準是典型的「田式風格」 ，帶有清晰明快的細節，最大限度的減少了推出孔之類該去除的累贅，小零件上面的合模線要特別注意。The first one, named modular intelligence ecology environmental protection housing, belongs to one kind of new monomer housing. it has realized the housing completely modulation, the standardized factory assembly line processing production. it may realize the housing itself energy zero supply, the housing security, defending against riots, and preventing from fire by the entire automatic controller
該生態住宅屬新型單體住宅，實現了住宅的全部模塊化標準化工廠流水線加工生產，可實現住宅本身的能源零供應家庭生活節水無回收價值垃圾的接近零排放等，同時可大幅度降低生產施工成本，提高土地的利用率，可作為別墅富裕農村民居中低層住宅樓度假村房屋工廠用房辦公樓酒店等多種用途。Consider three mutually perpendicular coordinate lines ( the -, -, and - axes ) with their zero point at a common point, called the origin. the three axes form the right - handed system, that is, if the fingers of the right hand are curled so that they curve form the positive - axes toward the positive - axes, the thumb points in the direction of the positive - axes
空間中三條相互垂直的坐標線，它們的零點相互重合，稱為原點，記為.坐標軸遵循右手法則，即以右手握住-軸，當右手的四個手指從正向-軸以角度轉向-軸時，大拇指的指向就是-軸的正向分享友人