霧化介質 的英文怎麼說
中文拼音 [wùhuàjièzhí]
霧化介質
英文
atomization medium-
First, a simple discussion for the mechanism about electrostatic atomization of the liquids has been given ; then the paper theoretically analyzed waving course, liquid drop producing course, and the liquid drop diffusing course in electrostatics atomization process., gave an analysis about the methods about carrying charges to the liquid drop, and analyzed that liquid with high electrical conductivity can be carried charges and atomized by electric field, while the isolated liquid with low electrical conductivity can be charged fully with the soakage electrode and inducing charge methods. at last the paper designed and configured the experimental equipment, conducted the atomization experiment to the three liquid medium - kerosene, emulsifier and alcohol under the same environment, handled the experimental results, then summarized the relationship between liquid electrostatic atomization effect and liquid surface tension, electronic conductivity and viscosity, along with the influence of voltage to electrostatic atomization and so on, found out the liquid atomization rule in high voltage electrostatic field
首先，對液體介質的靜電霧化機理作了初步的探討，理論上分析了液體霧化過程中射流區、波紋區、霧滴區和霧滴擴散區;然後對液體荷電方法進行了研究分析，對于高電導率的液體，場致荷電和接觸荷電可以使其霧化，而對于電導率較低的絕緣液體，需用浸潤電極荷電和感應荷電方法使其充分帶電;最後，根據前面的研究分析，設計和組裝試驗裝置，在同一環境下對煤油、乳化劑、酒精三種不同液體介質進行高壓靜電霧化試驗，並對試驗結果進行分析處理，總結出液體靜電霧化與液體表面張力、電導率和粘度的關系及電壓對液體靜電霧化的影響等，得出高壓靜電場中液體霧化的一般規律。The new developments of htm station technique were introduced from the aspects such as changing the htm pipeline type in pet htm station, increasing the switch forms of steam atomization and compressed air atomization, increasing the steam generator, sending stripping tower off - gas to combination and using new material nd steel in air preheater
摘要從改變聚酯熱媒站的熱媒爐熱媒管線形式、增加蒸汽霧化與壓縮空氣霧化的切換形式、增加蒸汽發生器、汽提塔尾氣送燒、空氣預熱器採用新型材質nd鋼等方面介紹熱媒站技術的新發展。The dried powder product was formed in the spray dryer by pressure nozzle which atomized liquid into small droplets and heat and mass transferring was performed between droplets and hot medium in the drying chamber
壓力噴霧乾燥裝置是利用壓力霧化裝置將原料液分散成細小霧滴，並與熱介質在乾燥塔內充分進行熱量、質量交換，最終達到乾燥產品的目的。An experimental system of electro - spray with two different charging methods - inducted by ring electrode and polarized by contacted needle electrode is established. an effective charging equipment for fuel is designed. water and kerosene ' s characteristics of charging and atomization in the electro - spray are measured and analyzed
2 、建立了環狀感應電極充電和閉式接觸電暈充電的荷電噴霧實驗系統，對煤油和水兩種不同物性介質的荷電特性與荷電霧化特性進行了測量及分析。Using compressed air and transformer oil as working substance, this paper studied the pressure characteristic of internal - mixing nozzle and acquired the experimental relation on the pressure in the mixing chamber of internal - mixing nozzle against the operation parameters and structure parameters according to the method of step by step regression
摘要以壓縮空氣和變壓器油為工質對內混式介質霧化油噴嘴的流量特性進行實驗研究，並通過逐步回歸分析的方法獲得了內混式介質霧化噴嘴油、氣流量系數與運行及結構參數的實驗關系式，可供設計使用部門參考。( 3 ) the most principal factors that influence the supersonic atomization process include the flow ratio of the gas - liquid metal ( gmr ) value, the flow of atomizing of gas and the range of the inverse vortex taper. the more of the value of three factors, the more advantage they are for the atomization and the more fine the powders are. ( 4 ) the produced powders are the best in efficient atomization efficiency, particle diameter, particle shape and dispersion when the solder alloy is zhl63a, atomizing medium is n2, the protrusion h = 6. 0mm, atomizing gas pressure p = 100mpa, over - heat temperature t = 167 ( t = 350 )
研究結果表明： （ 1 ）超音速霧化器的氣體流場在導液管下端形成一個倒渦流錐，在二維空間上呈軸對稱的雙峰分佈，負壓形成於這個倒渦流錐內； （ 2 ）修正後的霧化氣體速度公式可以滿足超音速霧化的要求； （ 3 ）影響超音速霧化工藝最根本的因素有氣液質量流率比（ gmr ）的大小、霧化氣體流量和倒渦流錐范圍，三個因素的值越大，對形成細粉越有利； （ 4 ）在焊錫合金為zhl63a ，霧化介質微n _ 2 ，導液管突出高度取h = 6 . 0mm ，霧化氣體壓力取p = 1 . 0mpa ，合金過熱度取t = 167 （ t = 350 ）時，所制得的粉末在有效霧化率、顆粒球形度、粒度及其離散度三個方面綜合性能最好。Then the paper also study the atomizer structure ( the protrusion of the delivery tube value h ), atomizing gas pressure p, over - heat temperature of alloy a t, the component of solder alloy and atomizing medium and so on
進一步對霧化器結構（導液管突出高度h ） 、霧化氣體壓力p 、合金過熱度t 、焊錫合金成份和霧化介質進行了研究。The present research and practical indicated that the effervescent atomizer may obtain the good atomization effect in the small alr situation, compares with the ordinary machinery and the medium spray nozzle, has the merits of saving the fuel, reducing pollution and so on, has the broad application prospect
目前的研究及實用表明，氣泡霧化噴嘴可以在小氣液質量流量比情況下獲得較好的霧化效果，與普通的機械和介質霧化噴嘴相比，有節約燃料，減少污染等優點，具有廣闊的應用前景。分享友人