非正比計數器 的英文怎麼說

中文拼音 [fēizhēngbǐjìshǔqì]
非正比計數器 英文
nonproportional counter
  • 非 : Ⅰ名詞1 （錯誤） mistake; wrong; errors 2 （指非洲） short for africa 3 （姓氏） a surname Ⅱ動詞1 ...
  • 正 : 正名詞（正月） the first month of the lunar year; the first moon
  • 比 : Ⅰ動詞1 （比較; 較量高下、 長短、距離、好壞等） compare; compete; contrast; match; emulate 2 （比...
  • 計 : Ⅰ動詞1 （計算） count; compute; calculate; number 2 （設想; 打算） plan; plot Ⅱ名詞1 （測量或計算...
  • 數 : 數副詞（屢次） frequently; repeatedly
  • 器 : 名詞1. （器具） implement; utensil; ware 2. （器官） organ 3. （度量; 才能） capacity; talent 4. （姓氏） a surname
  • 正比 : [數學] direct ratio; direct proportion
  • 計數 : count; tally; counting計數卡 numbered card
  1. The subject inducts digital time division technology ( pwm ), which is more advantageous at the accuracy and the predigest of hardware than simulant multiplication. what they call measuring power energy reasonably is that measuting except harmonics power energy fed back power. yet it realizes reasonable measurement of power energy which measures by base wave ac parameters method base on digital time division

    本課題引入了數字時分割（ pwm ）脈寬調制技術，在測量的準確性、硬體電路的簡化等方面都比模擬乘法器具有較高的優越性。所謂合理的計量電能，就是不計非線性負載回饋給電網的負的諧波電能，而採用基於數字時分割的基波交流參數測量的方法，真正實現了電能的合理計量。
  2. In order to make the sensitivity of 2 - demension accelerometer along the two main arbors almost identical, symmetric four - beam structure that embeds a double - sides interdigitated differential capacitive with puckered beam in two directions was used as sensitive component. in addition, the differential capacitive accelerometer fabricated by bulky silicon micromechanical technique has high sensitivity, wide measurement scope, less nonlinear error, and simple converting circuit. then, the structure parameters of the sensitive component were calculated and stimulated, which results in a set of the optimized structure design parameters, main fabrication procedure and several key fabrication technology

    為使二維振動傳感器在兩主軸方向的靈敏度大致相同，敏感元件採用高度對稱的四梁結構，其中每個軸向上均採用帶折疊梁的雙側叉指電容結構，採用體硅微機械工藝製作的高深寬比叉指電容式敏感元件，具有高靈敏度、寬量程、非線性誤差小、外圍電路簡單等優點;對設計的敏感元件結構參數進行了計算，並利用有限元法進行了模擬分析，根據模擬結果得出了優化參數;在確定敏感結構的基礎上，研究了敏感元件採用體硅微機械加工工藝製作的工藝流程和關鍵工藝技術;對敏感晶元內部的c - v介面電路進行了原理設計與分析，利用差動測量技術得到由振動引起的微小電容變化量，經c - v介面電路進行相位調制處理，然後通過解調輸出與加速度成正比的電壓信號。
  3. The conclusion is that inductive electromotive force, gotten from sensor with the distribution regularities of weighting function, is proportional to the average flow velocity in pipe and is not relevant to the distribution of flow velocity when flow velocity is non - central symmetry with the central axis. so electromagnetic flowmeter could solve the question of high accuracy in principles

    得出按權重函數分佈規律的傳感器，在流速非中心軸對稱分佈時，感應電勢僅與平均流速呈正比，而與流速分佈無關的結論，從而從原理上解決電磁流量計了高精度測量的問題。
  4. The first - order perturbation method correct for forcing decoupling method based on perturbation theory is put forward to decrease error ; iii. the complex modal method is introduced into analysis of non - classical damping systems to eliminate error of forcing decoupling method, and improve the complex modal response spectrum, which can apply to design of non - classical damping systems ; iv. for exerting the energy dissipation capability of each device, a two - step optimum method, whose controlling function is extremum expectation of interbedded displacement, is put forward to optimize the number and position of device ; v. the problem of iterative method applied to analyze energy dissipation systems is indicate, and give some primary advice based on pilot study

    為改善上述缺點，本文進行了以下的研究工作：在忽略耗能器附加質量的基礎上，推導出適用於耗能減震結構的攝動法，減少振型分解法在迭代計算過程中的工作量，加快計算速度；針對運動方程的強行解耦所產生的誤差，根據攝動法原理，對其進行一階攝動修正；為消除強行解耦振型分解法用於非比例阻尼結構分析時產生的誤差，引入狀態空間對系統進行復模態分析，並改進了基於復模態理論的、適用於非比例阻尼結構設計的雙反應譜方法；對于耗能器的數量和位置優化進行了一些探討和研究。
  5. The objective of this dissertation is a kind of press - high speed numeric control oil - press. with a theoretical analysis and study about proportional control system, this paper sets up the mathematical model of proportional valve controlled non - symmetry hydraulic cylinder via the hydraulic system model building. then analyzes and modifies the model based on the matter of this study, and simulates the model with matlab software to confirm pid parameters, thus designs the pid controller

    本學位論文針對一具體的研究項目?高速數控壓機的開發，對比例控制系統進行理論分析與研究，通過對液壓系統的精確建模，建立起比例閥控非對稱液壓缸的數學模型，然後根據所研究問題的實際情況對模型進行必要的分析和修正，再運用模擬軟體matlab分析系統模型及確定pid控制參數，設計出pid控制器，使得控制系統的設計具有更多的可靠性和靈活性，最後運用pic單片機實現此控制，並結合整機調試試驗驗證了pid控制的成功。
分享友人
分享到 Line

分享到臉書