預備頻率 的英文怎麼說

中文拼音 [yùbèibīnlǜ]
預備頻率 英文
stand-by frequency
  • 預 : Ⅰ副詞（預先; 事先） in advance; beforehand Ⅱ動詞（參與） take part in
  • 備 : Ⅰ動詞1 （具備; 具有） have; be equipped with 2 （準備） prepare; provide with; get ready 3 （防備...
  • 頻 : Ⅰ形容詞（次數多） frequent Ⅱ副詞（屢次） frequently; repeatedly Ⅲ名詞1 [物理學] （物體每秒鐘振動...
  • 率 : 率名詞（比值） rate; ratio; proportion
  • 預備 : prepare; get ready
  • 頻率 : frequency; rate
  1. The raw materials, the composition, the time of milling, the calcining temperature, the different additives, the sintering temperature and the sintering parameters were investigated. the result showed : it was advantaged to obtain high initial permeability mnzn ferrite with stable frequency characteristic using high - purity raw materials ; in order to obtain mnzn ferrite with high properties, we must control strictly the composition ; it could improve the properties of mnzn ferrite by optimizing calcining temperature. the lower calcining temperature made the permeability higher, and the higher calcining temperature could promote the frequency characteristic of permeability ; we chosen the right time of milling according to the requirement of power diameter ; in order to improve the properties of mnzn ferrite, it is necessary to add effective additives. in this dissertation, the influence of bi2o3 、 moo3 、 k2co3 、 co2o3 were investigated ; the sintering temperature, the time of heat - retaining and sintering parameters were the key factors of preparing high permeability mnzn ferrites

    研究結果表明:採用高純度的fe2o3有利於獲得高起始磁導率且頻率特性優良的鐵氧體;為了制備所需性能的鐵氧體，需要嚴格控制配方中各種原材料的含量，優化配方;由於粉體活性受預燒條件的影響，所以對不同要求的鐵氧體選擇的預燒條件就不一樣，適當降低預燒溫度有利於獲得較高的起始磁導率，而為了獲得良好的頻率特性可以適當地提高預燒溫度;根據對粉體顆粒粒徑的不同需求，可以選擇不同的球磨時間;而有效的添加劑是改善材料性能的必要條件，本文在添加劑的研究中主要對bi2o3 、 moo3 、 k2co3 、 co2o3的影響分別作了詳細地討論;燒結溫度、保溫時間和燒結氣氛是高磁導率mnzn鐵氧體制備最關鍵的工藝，適宜的燒結工藝可以獲得理想微結構和組成，從而得到高性能的鐵氧體材料;而從材料的微結構上來看，要提高材料的截止頻率，就要適當地細化晶粒、增加晶粒內部的氣孔。
  2. Secondly, two carbon fiber reinforced composite beams were fabricated, and their modal frequencies were measured by an experiment method. thirdly, delaminations were modeled by pairs of nodes with the same coordinates but different node numbers, while the modal frequencies of these beams with different delamination location and size were computed by an eas piezoelectric solid element. moreover, a novel method combining computational mechanics and neural network was demonstrated for composite health monitoring ; the first five flexure modal frequencies obtained by fem were modified by a primary revising approach and were used to train the neural network

    本文較全面地評述了神經網路的應用模型、改進演算法等，編制了bp神經網路程序：制備了纖維增強復合材料試件，並進行實驗模態分析；利用坐標相同、節點號不同的方法模擬脫層損傷，基於eas列式的壓電固體單元計算了不同脫層損傷情況下的頻率信息；針對基於實驗數據訓練神經網路存在樣本不足的缺陷，本文提出了利用有限元方法對含有脫層損傷的復合材料試件進行數值模擬，以前五階彎曲模態頻率構建訓練樣本的新思路，並提出了一種初步的計算值修正方法，以此構建神經網路的訓練樣本：將實驗模態分析的結果送入訓練好的神經網路進行預測，實現了對復合材料梁的脫層損傷的定位和損傷程度的評估。
  3. 1. nizn ferrite was developed for using in mini high frequency dc - dc converters and inductors. we measured and analysed the parameters of the nizn ferrite, which we concern about when designing the dc - dc converter. 2. the low loss sample of nizn ferrite were chosen for design - optimization of the high frequency transformer. based on the relevant theoretical researches, the loss properties of the magnetic core material and winding were analyzed in this thesis

    因此，以nizn功率鐵氧體材料為開關電源芯材為基礎，並優化各種開關電源的設計已成為國際上的熱點和技術瓶頸，本論文正是以上述背景為研究目標而開展工作的，主要進行的工作和創新有: 1 .對研製的新型高頻低功耗的功率nizn材料進行參數的測試，並針對dc - dc變換器設計關心的參數對芯材特性進行了分析，選擇在特定頻率下，功耗較小的nizn材料磁芯樣品作為變壓器優化設計的預備磁芯。
  4. It is important rules that research for dynamic characteristics of the mill system of single - pinion drives in operation to prevent damage from the resonance between fix frequency and bestir frequency in this paper, the pattern of pinion - - - drive shaft - - - decelerator gear vertical vibration in the mill system of single - pinion drives is established

    最後，對2 . 6 13m的磨機系統進行了動態特性的實例分析。研究邊緣傳動磨機系統的動態特性，對避免由於激勵頻率接近或等於系統的固有頻率而導致共振及設備的失效，預測系統在可能激勵下的響應特性，優化系統結構等等都具有很重要的意義。
分享友人
分享到 Line

分享到臉書