顯熱冷卻效果 的英文怎麼說

中文拼音 [xiǎnrèlěngquèxiàoguǒ]
顯熱冷卻效果 英文
sensible cooling effect
  • 顯 : Ⅰ形容詞1 （明顯） apparent; obvious; noticeable; evident 2 （有名聲有權勢的） illustrious and inf...
  • 冷 : Ⅰ形容詞1 （溫度低; 感覺溫度低） cold:冷水 coldwater; 你冷不冷? do you feel cold?; are you feeling...
  • 卻 : Ⅰ動詞1 （後退） step back 2 （使退卻） drive back; repulse 3 （推辭; 拒絕） decline; refuse; reje...
  • 效 : Ⅰ名詞（效果; 功用） effect; efficiency; result Ⅱ動詞1 （仿效） imitate; follow the example of 2 ...
  • 果 : Ⅰ名詞1 （果子） fruit 2 （事情的結局; 結果） result ; consequence 3 （姓氏） a surname Ⅱ動詞（吃...
  • 效果 : 1. （產生的結果） effect; result 2. [劇] sound effects
  1. Air cooler sensible cooling effect

    空氣冷卻器顯熱冷卻效果
  2. The thermal visualizations of jet impingement cooling with single or double row holes inside semi - enclosed channel are measured by using infrared camera and then the impingement cooling heat transfer coefficients are deduced. the effects of flow and geometry parameters on convective heat coefficients are obtained. the results show that : for a single row normal impingement, the impingement cooling effectiveness is enhanced with the increase of impinging reynolds number or the decrease of hole space to diameter ratio, and the best effectiveness is achieved under the jet - to - surface spacing equals to 2 ; when the jet is oblique to the confined wall, the cooling effectiveness is weaken especially under the jet - to - surface spacing ratio is greater than 2 ; for double rows normal impingement cooling, the cooling effectiveness of rear row jet is weaker than the front row under lower impinging reynolds number or bigger jet - to - surface spacing

    對于單排垂直射流，沖擊冷卻效果隨射流雷諾數的增加、孔間距與直徑比的減小而得到提高，沖擊間距比為2時換熱效果最好;沖擊孔中心線向通道封閉一側傾斜后，射流沖擊冷卻的范圍變窄，當沖擊間距比大於2時駐點區的對流換熱能力明顯降低;對于雙排沖擊射流，孔排間距與直徑比的增加使沖擊冷卻范圍變大，但在兩排孔之間區域的對流換熱系數有所下降;在較小的沖擊射流雷諾數和較大的沖擊間距比下，後排射流的沖擊換熱效果要遜於前排射流。
  3. The results indicated that, the fabrication process of ultra - fine grain material is mainly determined by the stress, rotate speed and the flux of cooling water. the grain refining and the hardening effect are mostly affected by the rotate speed and the flux of cooling water. compared with commercial ly12, the invalidate strength and the prolongation rate of the ultra - fine grain material are properly improved in the measurement of compression property ; and the abrupt change of the dilatability of the ultra - fine grain material at 500c is found ; also the phenomena of which the grain size of these microstructures is stable when annealed under 300c is observed

    研究表明，採用本文提出的摩擦壓扭強變形區轉移法可以得到棒狀的超細晶材料，軸向壓力、扭轉速度和溫度是採用該方法制備超細晶材料的主控參數；試件的旋轉轉速和冷卻速度對變形區晶粒細化和硬化效果影響顯著；超細晶ly12的壓縮性能與淬火+自然時效狀態的ly12壓縮性能相比，斷裂強度和延伸率均有一定程度的增強；超細晶ly12的熱膨脹系數在550左右發生明顯的變化。
  4. Measurements were made of system pressure, mass flow rate of steam, air, and cooling water, temperatures of condensing flow and cooling flow, and the water level of boiler. the major phenomena observed in the present experiment are similar to those by other investigators. the mass flow rate of steam, the system pressure and air content are the most important factors affecting steam condensation

    實驗結果表明，維持二次側冷卻水流量不變，無論對于純凈蒸汽還是含有空氣的蒸汽冷凝，隨著蒸汽發生器加熱功率的增大（即蒸汽流量增大） ，有效冷凝段長度將加長；當蒸汽中含有少量空氣，有效冷凝段長度也會明顯加長；提高系統壓力，有效冷凝段長度將縮短。
分享友人
分享到 Line

分享到臉書