驅動機構 的英文怎麼說

中文拼音 [qūdòngjīgòu]
驅動機構 英文
drive mechanism
  • 驅 : 動詞1. （趕） drive （a horse, car, etc. ） 2. （快跑） run quickly 3. （趕走） expel; disperse
  • 機 : machineengine
  • 構 : Ⅰ動詞1 （構造; 組合） construct; form; compose 2 （結成） fabricate; make up 3 （建造; 架屋） bui...
  • 驅動 : [機械工程] drive; prime mover
  • 機構 : 1 [機械工程] （機械的內部構造或一個單元） mechanism 2 （機關; 團體） organ; organization; institu...
  1. The amplitude at the driven end is fixed by the driving mechanism.

    由於驅動機構的作用，使驅動端的振幅保持不變。
  2. Coin and currency changers and actuators

    硬幣和貨幣兌換器和驅動機構
  3. Research on six - pole machine of manpower driving disc cropper

    驅動圓盤式人力收割機六桿驅動機構的研究
  4. Design drive mechanism, such as gearbox, drum etc

    驅動機構的設計，如減速箱，捲筒等。
  5. The rhombic drive mechanism has two "yokes".

    菱形驅動機構有兩個「軛」。
  6. The rhombic drive mechanism has two " yokes "

    菱形驅動機構有兩個「軛」 。
  7. Due to the electrohydraulic servo mechanism was used to drive the motion deck of the semi - physical simulator on the ground. therefore, the model of electrodraulic servo mechanism was built based on the fundamental equations of hydraulic jar and servo valve

    由於空間對接機構地面半物理模擬系統採用電液伺服驅動機構，因此本文根據電液伺服驅動機構的基本方程，建立單缸電液伺服驅動機構的模型。
  8. The feedbacks of position, velocity, acceleration and dynamic pressure were applied to adjust the model, so the control system of single jar electrodraulic servo mechanism was built. to reduce the system error and interference error, the compound control was designed. the results of simulations showed that the magnitude attenuation and phase lag of the system come to the project demand

    引入包括位置反饋、速度反饋、加速度反饋和動壓反饋在內的反饋控制技術對電液伺服驅動機構模型進行綜合校正，從而建立單缸電液伺服控制系統，並在分析系統誤差和擾動誤差后，加入復合控制減小系統誤差和抑制干擾，模擬結果表明復合控制系統的控製品質有了明顯改善，能夠滿足工程需求。
  9. Based on the kinematical design criterion of equi - chord percent ratio and spatial rigid body guiding mechanism, three theoretical design methods of arc track, non - arc track, and helical track are proposed in this thesis, meanwhile, different design methods about prime flap and sub - flap driving mechanisms are completed. three cases of different three - gaps - fowler - flap tracks are designed

    對后緣三縫富勒襟翼工作時的3個關鍵位置，按照「等弦長百分比」運動的設計準則和空間剛體引導機構的設計思路，提出了圓弧軌道、非圓弧軌道和螺旋線軌道等3種空間位置引導軌道的設計原理，並分別給出主襟翼和子襟翼驅動機構的不同設計方法。
  10. The modern unmanned helicopter flight control system is generally composed of the flight control computer, the servo driving mechanism, the sensor, and the ground monitor control system etc. in this thesis the research to the helicopter flight characteristics was conducted at first, and its flight dynamic model was preliminary discussed, especially the mathematic model under hung - stop condition was formulated and the algorithm of the controller was designed in detail

    現代無人直升機飛行控制系統一般由飛行控制計算機、伺服驅動機構、傳感器、地面監測控制等分系統組成。本文首先對直升機的飛行特性進行了研究，並且對飛行動力數學模型做了初步探討，尤其對在懸停狀態下的數學模型做了較為詳盡的公式推導和控制器的演算法設計。
  11. In this dissertation, both single and complex driver - magnifier as a whole body is tested and studied by the tool of ansys for the deep analysis of kinemics, workspace, error analysis and compensation. and the method of helix - mechanism is induced to study the model accurately

    本文利用ansys工具對智能並聯微執行器驅動機構的柔性鉸鏈進行了分析與模擬，為並聯微操作機器人整體性能測試及分析，即微執行器的位置空間、運動學、誤差補償提供了基礎。
  12. ( 3 ) planar full - crank five - bar mechanisms without uncertainty singularity are chosen to construct a hybrid mechanism generating the given path. a mathematical model is set up to optimize the dimensions of five - bar mechanism with the minimal power consume of the controlling motor by the improved genetic algorithms. an example is given to show the effectiveness of the mathematical model

    （ 3 ）第四章中，選取全曲柄五桿機構中的三種類型機構作為混合驅動機構，以減少用於控制其一連架桿運動的步進電機所消耗的功率為目的，建立相應的數學模型，用改進的遺傳演算法對該五桿機構進行優化綜合，求得尺寸參數。
  13. The formula and analysis would be helpful for the theoretical analysis and engineering design of the hydraulic cylinder piston ring seal structure

    研究結果為控制棒水壓驅動機構水壓缸活塞環密封結構的設計和分析提供了理論基礎。
  14. By analyzing the results of the crhdm single cylinder experiment, constants in the formula of the flow resistance were obtained

    利用控制棒水壓驅動機構單缸性能實驗的結果，擬合求得了流阻公式中的系數，並將公式計算流阻與實驗結果進行了對比。
  15. According to the control rod hydraulic drive mechanism ( crhdm ) and the characteristics of its hydraulic cylinder seal structure, the leaking ways of the hydraulic cylinder piston ring seal were analysed, its theoretical calculation model was built and its flow resistance formula based on the calculation model of differential pressure at the hydraulic cylinder piston ring seal was deduced

    摘要根據控制棒水壓驅動機構水壓缸活塞環密封結構的特點，分析了水壓缸活塞環的泄漏途徑，建立了活塞環密封泄漏流阻的理論計算模型，並結合水壓缸活塞環密封處的壓差計算模型，推導出水壓缸密封結構的流阻計算公式。
  16. Automotive starter drive remanufacturing procedures

    汽車起動機驅動機構的再加工程序
  17. Analysis of the driving force by friction in a driving structure of fdm

    工藝送絲驅動機構的摩擦驅動力分析
  18. In addition, the dynamic equation of the rotor with trailing edges and the 2 - x actuator has been modeled for analyzing the aerodynamic performance of the rotor. the result of the analysis tells us that the performance of the rotor with trailing edges can get a remarkable improvement

    進而研究旋翼動力學模型，將推挽式雙x驅動器模型作為后緣附翼的一種驅動機構，分析旋翼的氣動性能，模擬運算結果表明，后緣附翼智能槳葉在各方面的性能都有顯著的提高。
  19. The procedure of the test is as follows : first, the piezoelectric stack has been examined to test the performance parameters of the piezoelectric material ; second, the 2 - x actuator has been functioned with different static voltage to test its capability ; last, function the 2 - x actuator with voltage with different frequencies to test its dynamic properties. all the output of the actuator has been measured by the laser vibration measurement

    首先對壓電堆進行試驗，驗證壓電材料的性能參數;再對推挽式雙x驅動器施加不同的靜電壓驅動它，驗證作動器的驅動能力，最後對推挽式雙x驅動器輸入不同頻率的電壓驅動，測量該驅動機構的動態特性，試驗均採用激光測試儀測量推挽式雙x驅動器的輸出特性。
  20. Effect of driven - mechanism on natural frequency of torsional vibration of motor shaft

    被驅動機構對電動機軸扭振固有頻率的影響
分享友人
分享到 Line

分享到臉書