高壓氣體容器 的英文怎麼說

中文拼音 [gāoyāqìtǐróngqì]
高壓氣體容器 英文
high-pressure gas container
  • 高 : Ⅰ形容詞1 （從下向上距離大; 離地面遠） tall; high 2 （在一般標準或平均程度之上; 等級在上的） above...
  • 壓 : 壓構詞成分。
  • 氣 : Ⅰ名詞1 （氣體） gas 2 （空氣） air 3 （氣息） breath 4 （自然界冷熱陰晴等現象） weather 5 （氣味...
  • 體 : 體構詞成分。
  • 器 : 名詞1. （器具） implement; utensil; ware 2. （器官） organ 3. （度量; 才能） capacity; talent 4. （姓氏） a surname
  • 高壓 : 1 （殘酷迫害; 極度壓制） high handed 2 [氣象學] （高氣壓） high pressure3 （高電壓） high tension...
  • 氣體 : gas; gaseous fluid
  1. This paper aims at the characteristics of thermal response of lpg vesse1 under high temperatue, conjoining the project of " study on transportation safety early - wdring system of lpg dangerous goods " supported by transportation departinen of china and the project of " mechanism study and numerical simulation of the explosion of lpg vessel " supported by science foundation of hubei province. the interdisciplinary research has been done among temperature field distribution of lpg vessel under flame surroundings, intensity calculation, crack propagation predication and mechanism of explosive accident, etc. three parts are analyzed and discussed

    本文針對高溫環境下液化氣壓力容器的熱響應特性問題，結合交通部重點科技項目「液化氣體類危險品運輸安全預警系統的研究」和湖北省自然科學基金項目「液化氣容器爆炸機理研究及數值模擬」 ，對在火焰包圍下的液化氣壓力容器的溫度場分佈、強度計算、裂紋擴展預測以及爆炸事故機理等方面開展了多學科的交叉研究。
  2. The paper mainly discussed the reasons of stress from liquid ammonia pressure vessel causing crack through examing data and experimental results and analysing relevant referential documents and materials, taking 1200 ammonia vessel ' s crack and leaking in a certain fertilization company as an example : there existed remaining welding, stress in the equipment ; there existed a stress decaying surrounding, i. e., moisture 0. 2 %, and temperature > - 5 with o2 or co2 inside ; the higher the intensity of raw materials, more possible it was to have stress decaying crack

    摘要以某化肥公司1200氨冷器殼體開裂泄漏的失效分析為例，通過對檢驗數據和結果及有關文獻資料的分析研究，探究了液氨介質壓力容器產生應力腐蝕裂紋的原因：設備中存在較高的焊接殘余應力；液氨介質具備應力腐蝕環境，即含水量0 . 2 % ，且有空氣（ o2或co2 ）污染（或摻入） ，使用溫度高於零下5 ；母材強度越高，應力腐蝕裂紋產生的傾向就越大。
  3. The research of this paper includes : ? high - speed photography and flash x - ray radiography are both used to capture the process of al shell ' s great deformation under low pressure. front illuminations are used to get the development of the fracture on the al shell. the relative energy release is analyzed from overpressure curves measured with some sensors

    本文的研究內容主要包括： ?在受試炸藥經歷低應力大變形過程的susan試驗中，同時採用高速攝影、閃光x射線照相對彈體的撞靶過程進行了拍攝，得到了殼體膨脹變形過程圖像，並使用前照明技術觀察到了鋁殼表面產生的裂紋及其發展變化過程；從壓力傳感器測量的空氣沖擊波超壓曲線，獲得反應釋放總能。
  4. This new technology changes from the traditional method by which the induced and compressor wheel separately are designed and produced to a new one by which the one - piece compressor is designed. on the basis of this new technology and the optimum blade profile, the performance of both the compressor and the turbocharger is largely improved. through the heating power calculation of the compressor, the analysis of the surge and the block of the compressor, the test - bed performance test of the turbocharger, the matching test of turbocharger and diesel engine, the propulsion test of the turbocharger on plateau condition, it is proved that the newly - designed compressor not only has high efficiency, but also improves the flow distribution in the high efficiency area so that the propulsion line can run through the high efficiency area

    主要內容包括：提出一種全新的壓氣機葉輪技術和概念，這種技術將傳統的導風輪和壓氣機分開設計、單獨加工改為整體設計、整體加工的單體葉輪；從增壓器與柴油機配機計算所得出的基本參數出發，通過對壓氣機進行熱力計算，確定壓氣機的基本結構參數；再對葉型以及葉輪輪廓與葉輪罩殼的配合間隙進行優化，對新設計的壓氣機進行喘振和堵塞分析；通過增壓器平臺性能試驗，驗證了新設計的壓氣機的性能水平得到了較大的提高，達到了提高增壓器的整體性能水平的目的；通過增壓器與柴油機配機試驗、以及增壓器用於高原條件下的牽引試驗，驗證了新設計的壓氣機不但具有高效率，還改善了高效率區的流量分佈，使牽引特性線貫穿高效率區。
  5. With a decade of years of research and manufacture history on boilers and pressure vessel, complete quality control system, advanced production equipments, as well as well managed after sale service, " changcheng " autoclave becomes a brand trusted by many users, and has been used in fishery, chemical industry, glass industry, medicine industry, textile printing, heat insulating material, papermaking, timbering, civil construction and other industries

    十多年鍋爐壓力容器設計技術的潛心研究和製造歷史，完善的質保體系、先進的工藝裝備、無可挑剔的善後服務，鑄就「常成」蒸壓釜眾多用戶依賴的產品品牌，廣泛應用於漁業、化工、玻璃、醫藥、紡織印染、保溫材料、造紙、木材、加氣混凝土砌塊、粉煤灰砂、高強度水泥電桿、石膏蒸壓等眾多工業領域。
  6. About design programs of propylene tower post weld whole heat treatment, we have made analyses and compare from the various technical and economic aspects, and in vertical state of large pressurized vessel, we propose to adopt the internal combustion heat treatment method, in horizontal state of it, to adopt high temperature flue gas heat treatment method, and propose center combustion tube method as the future direction of technical developmnet insights

    摘要圍繞丙烯塔焊后整體熱處理的各種設計方案，從技術、經濟等方面進行分析對比，提出對超大型壓力容器，立置狀態下宜採用內燃法熱處理；臥置狀態時宜採用高溫煙氣法熱處理，並提出將中心燃燒管法作為今後技術發展方向的見解。
  7. In accordance with the technological difficulties encountered in the process of insulation supervision based on the dissolved gases analysis ( dga ), several kinds of model and method are presented to improve the reliability and precision of fault diagnosis of the power transformer. main research content includes : by deeply studying the common transformer faults diagnosing methods, such as three - ratio methods and improved electrical committee agreements, several shortcomings such as uncertainness judgment when the fault reasons, phenomenon and principles come out together while can not consistent to each other etc. for this reason, the old methods can not fully meet the need to engineering practical application. considering fuzzy relationship matrix can fully represents the causality between fault symptoms and fault types, when diagnosing complex equipments with multiple symptoms and fault causes such as power transformer, a synthetic fuzzy diagnosing model is firstly proposed to diagnose transformer ' s insulation faults based on dga in this paper

    本文針對應用油中溶解氣體分析方法進行變壓器絕緣監督時所遇到的主要技術難點，提出了提高變壓器故障診斷的準確性、可靠性的幾種模診斷方法，主要研究內容有：通過對判斷變壓器故障常用的三比值法和改良電協研法的深入分析，其診斷準確率較高，但對故障原因、故障現象和故障機理間同時存在不確定性和模糊性的變壓器等電氣設備的故障診斷，難于滿足工程應用的需要；在處理變壓器等結構復雜設備的多癥狀、多原因故障診斷時，模糊關系矩陣可以全面反映這種癥狀與故障類型間的因果關系，進而提出了變壓器故障診斷的模糊綜合診斷模型；同時作者還深入分析了模糊運算元的特性；針對常用的模糊評判結果的模糊集的集化方法的不足性，提出了將模糊綜合診斷與模糊規則推理結合起來進行故障診斷的方法，能達到較好的效果。
  8. Based on two application modes of the capsule accumulator in this system, the charge pressure and effective volume of the high pressure accumulator as an air spring and the performance parameters optimization with the jig working parameter determined was studied in this paper

    本文在簡要說明氣囊式蓄能器在跳汰機交流液壓系統中的高、低壓兩種應用的基礎上，對作為氣體液壓彈簧的高壓蓄能器工作容積的選擇與充氣壓力的問題進行研究，並在跳汰機工作參數確定的前提下，合理進行交流液壓系統中氣體液壓彈簧的參數優化。
  9. A high - pressure vessel, made of filament - wound composite, has been used in many demanding applications such as rocket generator cases, and oxygen and hydrogen tanks etc. in the aeronautic and astronautic industry, because of having many advantages

    纖維纏繞高壓復合容器具有許多優點而應用在航空和航天工程領域，例如：火箭發動機箱體，高壓氧氣或氫氣儲存器等。
  10. The sense of this work is to gain a further understanding of helium in the two metals. on the diffusion of helium - 3 in two spherical shell samples made of 21 - 6 - 9 type of stainless steel, during the storage of tritium at the pressure of 6. 13mpa for about 4 and 6 years at room temperature and later exposed to air for another 3 and 1 year. first, a calculation based on the analytical and numerical method to the diffusion and decay theories was developed to evaluate the concentration distribution of helium - 3 by tritium diffusion and decay in the samples

    在不銹鋼氚衰變~ 3he的擴散行為研究中，建立了氚和~ 3he濃度分佈的解析解和數值計算方法，以評估充氚不銹鋼球形容器壁中氚衰變~ 3he的宏觀濃度分佈，同時還用數值計算方法以求解氚和~ 3he的多步擴散行為；對樣品表面逐層蝕刻、同時收集釋放的~ 3he進行分析，分別實測了經室溫條件下在6 . 13mpa高壓氚中貯存4年和6年、空氣中存放3年和1年的兩種21 - 6 - 9不銹鋼球殼樣品內壁中~ 3he濃度分佈；結果表明：由於he在金屬中的不可容性， he原子偏聚于不銹鋼表面以及內部的局部區域，在整體趨勢上， ~ 3he分佈與計算結果相一致，根據理論計算，兩種21 - 6 - 9不銹鋼球殼樣品內壁中~ 3he到達的深度分別為350 m及500 m 。
  11. To meet the growing demand of china and asia market, chart invested 4 entities in china successively since 1995. adopting the advanced equipment, technologies and management from charts headquarter, chart china is able to provide china and asia market with various cryogenic equipment, such as liquid cylinders, bulk tanks, trailers, vacuum insulated pipe systems, according to the international codes as well as chinese code and regulations, and better service and technical support for customers of these regions

    為了適應中國及亞洲地區經濟高速發展的市場需求，查特mve從1996年起先後在中國投資建設了4家公司，應用美國查特公司總部的先進設備技術和管理，按照國際相關標準及中國壓力容器現行規范和標準進行深冷設備的生產製造，為國內及亞洲地區的客戶提供世界一流品質的焊接絕熱氣瓶真空絕熱管道大型深冷貯罐低溫液體槽車等各種深冷設備，同時為客戶提供更及時周到的服務與支持。
  12. Answer : ( 1 ) prevent to splatter the metal is caused burnable with fire ; ( 2 ) avoid the harm of electric arc ray radiation to human body ; ( 3 ) prevent certain and harmful gas toxic ; ( 4 ) soldering when pressure vessel, should prevent to solder produce explosion ; ( 5 ) when headroom works, want to take safety belt and safety helmet ; ( 6 ) the attention prevents accident getting an electric shock

    答： （ 1 ）防止飛濺金屬造成灼傷和火災； （ 2 ）防止電弧光輻射對人體的危害； （ 3 ）防止某些有害氣體中毒； （ 4 ）在焊接壓力容器時，要防止焊接發生爆炸； （ 5 ）高空作業時，要帶安全帶和安全帽； （ 6 ）注重避免觸電事故。
分享友人
分享到 Line

分享到臉書