高壓氣體噴射 的英文怎麼說

中文拼音 [gāoyāqìtǐpēnshè]
高壓氣體噴射 英文
high-pressure gas injection
  • 高 : Ⅰ形容詞1 （從下向上距離大; 離地面遠） tall; high 2 （在一般標準或平均程度之上; 等級在上的） above...
  • 壓 : 壓構詞成分。
  • 氣 : Ⅰ名詞1 （氣體） gas 2 （空氣） air 3 （氣息） breath 4 （自然界冷熱陰晴等現象） weather 5 （氣味...
  • 體 : 體構詞成分。
  • 噴 : 噴動詞1. （液體等受壓力而射出） spurt; spout; gush; jet 2. （噴灑） spray; sprinkle
  • 射 : Ⅰ動詞1 （用推力或彈力送出） shoot; fire 2 （液體受到壓力迅速擠出） discharge in a jet 3 （放出） ...
  • 高壓 : 1 （殘酷迫害; 極度壓制） high handed 2 [氣象學] （高氣壓） high pressure3 （高電壓） high tension...
  • 氣體 : gas; gaseous fluid
  1. The characteristics of high pressure gyratory sprayed pumping discusses is presented, which is applicable in wide range of scope and ground layers, convenient for construction, long durability, wide source of materials. mechanism for subgrade strengthening : complex foundation of cement solid and earth between piles was formed by pulsant load of flowing pressure and spraying flow, water wallop, cavitation phenomenon, water wedge effect, extrusion force and air flow agitation etc so as to enhance foundation bearing force and reduce settlement and deformation

    高壓旋噴注漿技術具有適用范圍、適用地層較廣，施工方便，耐久性好，材料廣闊等特點；其加固地基機理主要是通過流動壓、噴射流的脈動負荷、水塊的沖擊力、空穴現象、水楔效應、擠壓力、氣流攪動等效應形成水泥固結體與樁間土的復合地基，從而提高地基承載力，減少沉降變形。
  2. A reasonable position of driving nozzle helps to achieve the maximum material flow that also depends on other parameters such as backpressure, properties of conveyed material and driving gas. it is observed that, an increase of convergent section angle is harmful to the pneumatic conveying system, and also influences on the mass flow rate of conveyed material, the distribution of static pressures in injector and the pressure drops of conveying pipe. in addition, within a reasonable scope of air mass rate, increasing the driving jet velocity is more advantageous than enlarging the dimension of driving nozzle

    試驗研究發現，氣體噴嘴位置對氣固噴射器的輸送能力影響最大，氣體噴嘴存在某一最佳位置，而這一最佳位置與背壓、輸送物料特性和輸送風特性相關聯；氣固噴射器的收縮角對其輸送能力、內部靜壓分佈和輸送管阻力特性均有適量影響，收縮角增大對整個輸送系統均不利；在適當的輸送風范圍內，提高氣體噴嘴出口速度比擴大氣體噴嘴尺寸更為有利，但氣體噴嘴出口速度過高會增加氣固噴射器和輸送管內的能量損耗，給輸送帶來不利的影響；系統背壓與氣固噴射器的氣體噴嘴出口速度的選取有關。
  3. The innovation is that a ring bar sprayed bubbling gas distributing device is installed at the bottom of the tower, which has novel effects of leveling off gas and decompressing, cooling and dust removal, highly effective absorption, hydraulic stiring and so on at the same time

    其創新點是在塔的下部嵌入了一個環柵噴射鼓泡式進氣裝置，其新穎之處體現于：煙氣穩流減壓，冷卻除塵，高效吸收，氣力攪拌等功能可在環柵通道內一氣呵成。
  4. Material is ejected into the crushing chamber by means of high speed ejection flow formed by high - pressure air through charging ejector, and the crushing nozzles outside ejects high - speed airflow into the crushing chamber at certain direction, making the materials severely collided and fractionated, and thus crushed

    該機是靠高壓氣體通過加料噴射器所形成的高速射流，使粉碎原料被射入料碎室，粉碎室外圍的粉碎噴嘴，有方向性的向粉碎室噴射高速氣流，使物料間產生激烈的碰撞，磨擦而獲得粉碎。
  5. The conclusions are drawn as following : 1. regularity of fabrication in aluminum matrix composite ring - shaped performs with large dimensions and effects of parameters were investigated, based on the novel crucible movable spray deposition technology and equipment. the optimal parameters are that the diameter of the delivery tube is 3. 8mm, spray gas pressure is 0. 8mpa, spray height is 200mm, and transferring pressure of sic is 0. 5mpa

    通過系統的實驗研究得到如下結論: 1 .基於新型的移動坩堝自動化控制噴射沉積環坯制備技術及裝置，研究了大尺寸鋁基復合材料環坯的制備規律，討論了噴射沉積工藝參數對沉積坯形成過程的影響，得到了最佳工藝參數:導流管直徑d = 3 . 8mm ，霧化氣體壓力p = 0 . 8mpa ，噴射高度h = 200mm ， sic顆粒輸送壓力p送= 0 . 5mpa 。
  6. In the text, there analyzes the process of the mixture air and fuel in the two stroke gasoline engine and bring forward the specific solution to the improvementsing gasoline engine the high - press direct in - cylinder injection. this technology sprays the feul into the cylinder after the outlet vavle closed and scavengs the engine cylinder with pure and fresh air, which avoid the fuel escapes unburned

    本文分析了二沖程汽油機混合氣形成過程，並提出了具體的改進方案，用缸內高壓直接噴射技術進行改造。缸內高壓直接噴射是在發動機排氣口關閉後向氣缸內噴射燃油，使用純新鮮空氣進行掃氣，避免了燃油短路損失。
  7. It is shown that when the exit area of secondary nozzle and the fuel / oxidizer ratio is fixed, the increase of mass flow rate of secondary flow lead to the decrease of velocity of mixed flow, and increase of total mass flow rate. the synthetical result of these two phenomenon cause the increase of thrust of rocket ejector, but the increasing magnitude is relatively small, indicating that these is no necessary to claim large bypass ratio in rocket ejector design. in the comparison between two configurations, the typical one has better performance, indicating the importance of pressure ratio

    結果表明：在固定二次噴管出口面積和氧燃比的條件下，二次流（引射空氣流）流量的增加引起混合氣體出口速度的下降和總流量的增加，二者綜合作用使發動機推力增加，但增幅不大，表明在設計發動機結構和工作參數時，不必過分追求大的引射系數；兩種結構的性能對比分析表明了增壓比對引射火箭性能的提高具有重要意義；對引射火箭的熱力循環分析同樣表明，增壓比對于提高發動機性能非常關鍵。
分享友人
分享到 Line

分享到臉書