高溫淬火 的英文怎麼說

中文拼音 [gāowēncuìhuǒ]
高溫淬火 英文
hot quenching
  • 高 : Ⅰ形容詞1 （從下向上距離大; 離地面遠） tall; high 2 （在一般標準或平均程度之上; 等級在上的） above...
  • 溫 : Ⅰ形容詞（不冷不熱） warm; lukewarm; hot; gentle; mild Ⅱ名詞1 （溫度） temperature 2 （瘟） acute ...
  • 淬 : 動詞（淬火） temper by dipping in water, oil, etc. ; quench
  • 火 : fire
  • 高溫 : high temperature; elevated temperature; hyperthermia; megatemperature; inferno
  1. Our company endeavors to quenching & tempering, normalizing, tempering, high and medium temperature quenching, mesh belt furnace quenching, carbonizing, aging subzero and high temperature heat treatment, etc

    本公司是一家致力於從事調質、正火、回火、高中溫淬火、網帶爐淬火、滲碳、時效冰冷及其高溫熱處理的廠家。
  2. Over 310, liquid nitrogen quenching and water quenching show higher damping capacities

    當溫度大於310 ， - 195淬火與水淬試樣表現出較高的阻尼性能。
  3. The principle of multi - method and multi - parameter is suggested, which should be followed during characterizing microstructures of alloy steels by ultrasonic not method. ultrasonic velocity ( c, ) of transformation products through different heat processes of three steels was measured by high - accuracy ultrasonic installation. the velocity of quenched microstructure of 38crmoal is the lowest, which gradually increases with increasing tempering temperature between 200 ? and 650 ? after quenching process

    利用ti - 40n高精度超聲波測厚儀，研究了超聲波在不同鋼種、不同熱處理轉變產物中的超聲波速度c _ 1 : 38crmoal鋼淬火組織c _ 1最小，淬火后在200 650范圍內進行回火處理時，隨回火溫度的升高， c _ 1逐漸升高， hrc與c _ 1之間具有較好的相關性；正火組織的c _ 1介於淬火后中溫回火及高溫回火產物組織的c _ 1之間。
  4. Sub - temperature quenching process of high strength bolts

    高強度螺栓的亞溫淬火工藝
  5. Abstract : a new simulating method is established for the calcul ation of the hardness profile of high - carbon - concentration deep - carburization, on the basis of analyzing this process and taking into account the influence o f carbide solution and dissolution, carbon - concentration and temperature on the diffusion behavior, and the influence of the environment factor on carbon trans fer through the gas - solid interface

    文摘:在對高濃度深層滲碳的特點進行分析的基礎上，考慮到碳化物的析出與溶解、溫度及碳濃度對擴散行為的影響，氣氛環境對相界面碳傳遞過程的影響，淬火烈度對滲碳層冷卻效果的影響，提出了一種新的模擬高濃度深層滲碳滲層硬度分佈的方法。
  6. Results of the experiments showed that the wear mechanisms of the sintered steel included abrasive wear, adhesive wear and fatigue wear, and it was the abrasive wear most important. it was the sintered steel mixed by ni, mo that was the best on the wear resistance, because of the great lot of bainite ; the sintered steel quenched and low temperature tempered mixed by mo, w that was the best on the wear resistance, because of the rigidity of the steel was the highest

    實驗結果表明：本文中幾種燒結鋼的磨損機制均是由磨粒磨損、粘著磨損、和疲勞磨損共同作用的，且以磨粒磨損為主；在燒結態下，復合添加合金元素鎳、鉬的燒結鋼的耐磨性能最好，這是因為生成了大量的硬質相貝氏體；而淬火、低溫回火態下，則復合添加鉬、鎢的燒結鋼的耐磨性能最好，這是因為熱處理態下添加鉬、鎢的燒結鋼的硬度最高。
  7. The variation principle of wave velocity in different microstructures of 40cr is similar with that of 38crmoal. the velocity in quenching and low temperature tempering structure of gcrlssimn is much lower than the velocity in normalizing, annealing and high temperature tempering structure

    Gcr15simn鋼淬火+低溫回火組織的c _ 1遠大於正火、退火及淬火+高溫回火組織的c _ 1 ；正火、退火及淬火+高溫回火組織的c _ 1比較接近。
  8. The difference among the elasticity modulus of various microstructures is probably the main reason, which caused the experiment results above. under the same experiment conditions, such as sample shape, size, surface roughness, establishment of testing system, pressure on the probe, and thickness of coupling medium, the variety of relative attenuation coefficient ( or ) in different heat treatment samples is measured and compared by measuring the attenuation obtained from the cylindrical surface of column. the result is as following : for 40cr and 38crmoal, a mt < az mq < a s < a p + f ; for gcrlssimn, a mt < a annea < s < a p + f ; and a increased with the increasing of frequency

    在保證試樣形狀、尺寸、表面光潔度、系統參數設置、施加在探頭上的壓力以及耦合層厚度等測試條件一致的情況下，利用棒材圓柱面測衰減系數法，分別測定並比較上述不同熱處理試樣相對衰減系數的變化情況，得到的實驗結果是：對於40cr及38crmoal鋼， _ （低溫回火） （淬火） _ （高溫回火） _ （正火） ；對于gcr15simn鋼， _ （低溫回火） _ （退火） _ （高溫回火） _ （正火） ；且隨著頻率的提高，衰減系數均呈現增加的趨勢。
  9. According to structural characteristics of multi - phased alloy steels and the properties of ultrasonic propagation, microstructures characterization with different heat treatment processes ( normalizing, quenching / annealing, quenching plus low tempering, quenching plus high tempering ) for three steels ( 40cr, 38crmoal, gcrlssimn ) was studied experimentally by using ultrasonic methods. ultrasonic velocity, relative attenuation coefficient, and power spectral analyses were researched on the same samples respectively, on the basis of theory and experiment, the sensitivity and other characterizations of the three methods used to distinguish different microstructures were compared

    根據具有多種相結構合金鋼不同熱處理轉變產物的組織特點，以及超聲波在其中的傳播規律，利用超聲波速度、相對衰減系數以及功率譜分析三種方法，對三種鋼（ 40cr 、 38crmoal及gcr15simn ）不同熱處理（正火、淬火退火、淬火+低溫回火及淬火+高溫回火）轉變產物的顯微組織進行了超聲表徵研究。
  10. The company is specialized in producing of mesh - belt continuous sintering furnace 、 pusher - type high temperature sintering furnace 、 steel - belt iron powder refining reduction furnace （ electric - heating rbo furnace and direct gas - burning heating rbo furnace are also produced ） 、 pressure bell type furnace 、 carburizing quench furnace and some kinds of accessorial equipments

    目前生產項目有：網帶式連續燒結爐、推桿式高溫燒結爐、蒸汽處理爐、鋼帶式鐵粉還原爐（電加熱、氣體燃燒直接加熱rbo型均生產） 、加壓鐘罩爐、滲碳淬火爐及各種輔助設備。
  11. The lath width of martensite can be fined noticeably by pre - strained quenching at non - dynamic recrystallization to approach nanometer magnitude ( the average width is 120nm )

    採用非動態再結晶溫度下的預應變-淬火，提高馬氏體相變形核率，可以超細化馬氏體的板條晶片寬度，使之接近納米量級水平（平均寬度達到120nm ） 。
  12. From an examination of the tensile behavior of cz ly12 alloys under different temperature and strain rate, two kinds of deformation and intergranular fracture behaviors were observed that were opposite to the characteristic strain rate range in fine - grained superplasticity. the mechanisms are described as follows. the high ductility achieved at high strain rate is generally attributed to the dominant role of gbs accommodating mechanisms, which is considered as dislocation creep within grains controlled by subgrains

    研究選用自然時效淬火態的ly12鋁合金，進行了一系列不同溫度和應變速率下的單軸拉伸試驗， 480下，觀察到與傳統細晶超塑性特徵區間相反的行為：較高應變速率下，動態再結晶使晶粒細化，促進了晶界滑移，亞晶界控制的晶內位錯蠕變是晶界滑移的主要協調機制。
  13. As shown in the figure left, the inner ring of the self - contained bearing is hardened in the race - way and surroundings part where hardening is necessary, the area of set screw hole of the inner ring has been templed by high temperature after hardened, it has higher toughness and impact clasticity

    如左圖所示，內圈溝道及其周圍需要淬硬的部分已經過正常淬火，裝配緊定鏍釘的內圈伸長端則經過高溫局部回火而保持韌性及抗沖擊性。
  14. Annealing could reduce hardness and raise toughness, which could be prone to mechanical machining. quenching and low temperature tempering could raise intensity and hardness of materials, not reduce toughness obviously. quenching on same temperature caused ticp / fe in situ composites having the best integral machine properties

    退火處理使材料的硬度降低，韌性提高，便於機械加工；淬火+低溫回火處理使材料的強度和硬度提高，而韌性無明顯的降低；採用等溫淬火工藝，可使tic _ p fe復合材料具有最好的綜合機械性能。
  15. Our solid carbide tools have been widely used in aviation, space, auto, mould etc. industries, can be applied to materials of cast iron, steel, stainless steel, alloy steel, harden steel, mould steel, tool steel, bearing steel, heat - resistant alloy, titanium alloy, nickel, plastic fiber, aluminum alloy, copper

    喜威一合金刀具目前已廣泛應用於航空，航天，汽車，模具等行業，用於加工灰鑄鐵，球墨鑄鐵，碳鋼， ，軸承鋼，模具鋼，合金鋼，工具鋼，淬火鋼，調質鋼，不銹鋼，玻璃鋼，鋁合金等軟金屬，鈦合金，鎳基高溫合金。
  16. The effect of plastic deformation and elastic strain energy induced by pre - strain on the nucleation of martensitic transformation of low alloy ultra - strength steel sosimncrmov had been studied by pre - strain quenching in austenite state. the control over deformation magnitude and deformation temperate as well as loading pattern was performed to adjust the storage of elastic strain energy in steel before martensitic transformation, using the type of geeble - 1500 thermal analogue test machine

    使用gleeble - 1500型熱模擬機，對低合金超高強度鋼30simncrmov實施奧氏體預應變淬火處理，通過控制形變量、形變溫度和加載方式，調整鋼中馬氏體相變前的彈性應變能儲備，研究了預應變所造成的塑性變形與彈性應變能對馬氏體相變的影響。
  17. The results show that, with the quenching temperature ( 270 ~ 380 ) increasing, the carbon content and percentage content of retained austenite increase first and then decrease, which are up to a maximum value at 360 ; the tensile strength of adi decreases ; the elongation and impact ductility of adi increase first and then decrease, which are up to a maximum value at 360 ; but the hardness of adi decreases first and then increases, which is up to a minimum value at 360

    結果表明，在試驗溫度范圍內（ 270 ~ 380 ） ，試樣中殘余奧氏體的含碳量及其含量隨著等溫淬火溫度的升高先增大后減小，均在360等溫淬火時出現最大值；抗拉強度隨著等溫淬火溫度的升高而逐漸降低；伸長率和沖擊韌度隨著等溫淬火溫度的升高先增大后減小，在360等溫淬火時出現最大值；硬度則隨著等溫淬火溫度的升高先減小后增大，當360溫淬火時硬度最低。
  18. This company endeavors to hardening, normalizing, tempering, high and medium temperature quenching, mesh belt furnace quenching, cementing, time effective freezing and high temperature treatment etc

    本公司是一家致力於從事調質、正火、回火、高中溫淬火、網帶爐淬火、滲碳、時效冰冷及其高溫熱處理的廠家。
  19. 2. heating treatment : 1300065002580mm annealing furnace max furnace is 120t, the high temperature is 11500c, 620023001500mm hardening furnace, 11005000mm line - frequency hardening machine tool

    2熱外理： 1300065003580mm退火爐最大裝入量120t最高爐溫11500c 620023001500mm淬火爐11005000mm工頻淬火機床。
  20. Application of short - time high - temperature quenching for 45 steel mould parts

    短時高溫加熱淬火在45鋼模具零件上的應用
分享友人
分享到 Line

分享到臉書