齒形的 的英文怎麼說

中文拼音 [chǐxíngde]
齒形的 英文
castellated
  • 齒 : Ⅰ名詞1 （牙; 牙齒） tooth 2 （物體上齒形的部分） a tooth like part of anything 3 [書面語] （年齡...
  • 的 : 4次方是 The fourth power of 2 is direction
  1. The gearing machine tool of the model y3150e is modified and a new milling head is designed to cut the envelope tooth of the pinion using allelomorph method. a assembled drawing of clamp for cutting the tooth shape of circle - arc gear is also presented

    對y3150e型滾齒機進行改造，設計出一新型的銑削頭，利用對偶法加工小齒輪的圓弧包絡線齒形；同時也給出了加工大齒輪圓弧齒形的夾具裝配圖。
  2. Study on gear tooth surface of generating spur bevel gear

    滾齒直齒圓錐齒輪齒形的研究
  3. Machining of involute profile of die on wedm

    模具漸開線齒形的電火花線切割加工
  4. Shank nuts, self - locking, serrated - installation procedure

    細齒形的螺桿自鎖螺母.安裝程序
  5. Size and obliquity of tooth directly influence clutch whether normal operating. it is a key part for ensuring normal operating of aira too. this article fully deduces their compute formula

    該齒形的大小、傾角直接影響離合器是否能正確地嚙合和分離，也是保證機構進行正確工作的關鍵部分，本文詳盡推導了它們的計算公式。
  6. One of tooth profiles of coarse - pitch gear ball hob is analyzed in engagement theory ， the tooth profiles of the internal gear has been derived. by comparing the tooth profile with the tooth profile of the standard internal gear, it is shown that the tooth profile is satisfying

    對大模數內齒輪球形滾刀的一種齒形進行嚙合理論分析，求出滾刀加工出來內齒輪的齒形，然後與標準內齒輪的齒形比較，結果表明：該齒形的滾刀加工的內齒輪能滿足要求。
  7. Study on distributing construction of the sliding - tooth pump

    修正齒形的復合齒輪泵流量特性
  8. The results indicate that if the value of press stress is over certain figure, press stress and al plate ’ s thickness have little influence on sawtooth distortion for the same kind of sawtooth ; sawtooth distortion is well - regulated under static press, while it is irregular under impact press. bottom coating make great influence on bond strength of samples which can improve the value remarkably ; bonding mechanism of clad steel is mechanism of mechanical effect that sawtooth which is hooked occludes with al plate

    結果表明：同種齒型，當壓應力大於一定的值時，壓應力和覆板的厚度對齒形的變化影響不大；靜壓下齒形變化比較規則，鋸齒頂端向一側彎曲成鉤狀；沖壓下齒形比較凌亂，鋸齒的頂端沒有明顯的變形；后處理對試樣的結合強度影響很大，打底試樣由於粘結層的作用，結合強度較高；機械作用機制是復合鋼板的主要復合機理，鋸齒彎曲成鉤狀和鋁板形成機械咬合。
  9. Through the simulation of the forming process, we can get the deformations, stress, strain, plastic flowing in sheets and the interface state under impact load and rolling load, the deformation of the sawtooth form and comparing to the initial state, the results above are expressed in computer animated way. and the effect of geometrical ( mainly different form, including 90 degree, isoceles triangle ， 75 degree, and 1. 5 high and wide ), material and technical parameters on the bond strength are analyzed, also including the comparison of different sawtooth form. the optimum parameters are got

    對雙金屬復合板成型過程進行模擬，從而得到在沖擊載荷和軋輥壓力作用下基板和覆板的應力、應變分佈和塑性流動變形規律，復合后的齒形的變形情況與初始齒形形成對比，以動畫的方式模擬成型過程，並分析了不同幾何參數（主要是不同的齒型，其中包括直角齒型、等腰齒型、 75度齒型、 1 . 5高寬齒型） 、材料參數、工藝參數對復合強度的影響，以及不同齒型的變形對比以及齒型對復合情況的影響，提出最優齒型、最優工藝參數，有效地指導了實驗。
  10. Measuring methods of ultraprecision involute tooth profile

    超精密漸開線齒形的測量方法
  11. The profile determination of involute finger - type milling cutter

    漸開線指形銑刀齒形的確定
  12. To measure and calculate involute profile

    漸開線齒形的測量推算
  13. The passage and chamber stones are also richly engraved with spiral, lozenge and zigzag motifs

    走廊和內廳的石頭上也被刻上了豐富的螺旋形、菱形和鋸齒形的圖案。
  14. The investigation for the profile of asymmetrical involute gear

    非對稱齒廓漸開線齒輪齒形的模擬設計分析
  15. The points of internal gear are fitted into spline curve by spline function, then the internal gear is manufactured in nc wire - cut machine. the process of manufacturing the internal gear in wire - cut machine is studied. compared to the traditional method of manufacturing in special machine this process is a breakthrough

    利用樣條函數對中心輪內齒圈齒形點進行擬合，利用軌跡法在數控線切割機床（ bkdc ）上實現了中心輪內齒圈齒形的加工，並對在數控機床上加工的工藝進行了研究。
  16. For the first time, the internal gear is measured on three - coordinate measuring machine, gear error of internal gear is calculated and analyzed by comparing the measuring data with the desired data. the result of analyzing reveals the correctness of math model and manufacturing method

    首次在三坐標測量機上實現了中心輪內齒圈齒形的檢測，並把檢測數據與理論數據進行比較，求出了中心輪內齒圈的齒形誤差，通過對齒形誤差的分析，證明了以上數學模型是正確的，加工方法是可行的。
  17. Zigzag bolts of lightening flash across the sky the clap of thunder echoes across the water

    鋸齒形的道道閃電相繼劃破長空，聲聲雷鳴在水面上回響。
  18. I was not unprepared for jagged rocks and treacherous, shoals it i could only have change - change and the excitement of unforeseen

    我對鋸齒形的巖石是不無準備的和叛逆的，淺灘它我只可以有變化-變化和刺激無法預料的。
  19. To the northwest and north of beijing, a huge, serrated wall zigzags it s way to the east and west along the undulating mountains

    在北京西北和北面連綿的群山中，一道鋸齒形的高墻隨山勢起伏蜿蜒，向東西方向延伸，不見首尾。
  20. Still dark green near its stem, with its serrated edges tinted with the yellow of dissolution and decay, it hung bravely from the branch some twenty feet above the ground

    靠近莖部仍然是深綠色，可是鋸齒形的葉子邊緣已經枯萎發黃，它傲然掛在一根離地二十多英尺的藤枝上。
分享友人
分享到 Line

分享到臉書