齒條軸 的英文怎麼說
中文拼音 [chǐtiáozhóu]
齒條軸
英文
rack shaft-
Results : 1 ) under the same condition of loading, the stress and displacement of mesial occlusal rest design was smaller than that of distal occlusal rest design in abutment teeth and soft tissue under the base, however, the magnitude in the soft tissue under base was bigger. 2 ) when a distributed vertical load was applied to the artificial tooth abutment teeth regions, the stress distribution was similar to that of concentrated load in the artifitial tooth, and stress magnitudes were higher. 3 ) under the condition tested, the mesial occlusal rest design caused the stresses that were more in line with the long axes of the abutment teeth than did the distal occlusal rest design
結果： 1 ）在同一加載條件下，近中（牙合）支托設計與遠中（牙合）支托設計相比，基牙及基托下軟組織的應力和位移值減小；基托下軟組織的應力和位移值大於基牙； 2 ）基牙及義齒整體加載時，各基牙應力分佈規律與人工牙加載相同，但應力值增大； 3 ）近中（牙合）支托設計使基牙受力更趨于軸向。Tabular layouts of article characteristics for racks, cylindrical gears, pinion shafts, bevelgears, bevel pinion shafts, worms and worm wheels
齒條圓柱齒輪小齒輪軸傘齒輪圓錐齒輪軸蝸The main parts such as axles, squeezer, pressing bar and gear are made of advanced alloy steel which has been handled by hardening and can be used everlasting even though in the condition of high temperature and friction consumption all day and all night
本機主軸、榨螺、榨條、齒輪等主要零件，均系優質合金鋼製造，並經過硬化處理，雖日夜處于高溫與摩擦耗損情況下，均能經久耐用。Through systemic analyzing on spiral helical gear transmission with different basic parameters, the essay found out rules of how can such basic parameters influence spiral helical gear engagement characteristics. so it brings forward the auxiliary assembling mode of adopting one straight gear and one helical gear on condition of little axial angle as well as treasures to ameliorate ill engagement performance on condition of large axial angle, another two jobs of the essay are to clarify the wrong concept that spiral helical gear can only transmit movement but not impetus and to provide a brief and practical method of analyzing contact for gear pairs whose surface equations can be written out directly
通過對不同基本參數的螺旋齒輪傳動進行系統研究，找出了螺旋齒輪基本參數對其嚙合特性的影響規律，提出小軸交角條件下可採用一直齒輪、一斜齒輪的齒輪副組合方式，給出了大軸交角條件下嚙合性能不良的改進措施。澄清了螺旋齒輪只能傳遞運動不能傳遞動力的誤區，為能夠直接寫出齒面方程的齒輪副進行齒面接觸分析提供了一種簡便、實用的新方法。The moment distribution principle of differential with regard to condition of frictinal moment of partial gear
考慮半軸齒輪摩擦力矩條件下的差速器轉矩分配原理Then the non - interventional condition is that the relative geodesic curvature is zero. furthermore, for the transmission of the parallel or crossing axles, if the datum surface is the pitch one, the non - interventional condition is naturally satisfied
考慮到平行軸的法向圓弧齒輪傳動已臻成熟，論文重點研究了相交軸與交錯軸條件下法向圓弧齒輪傳動的基本方案。Piaget has gone from rotary research to jewelry watch - making, mechanical timepieces to quartz design, a workshop with only six craftsmen to a factory with more than two hundred workers, but still the company piaget strives for perfection, a principle that drove its founder, george, over a hundred years ago
從齒輪研究到鉆石軸承表製作，從機械鐘表到石英鐘表，從只有六名工匠的作坊到擁有二百多名工人的工廠，伯爵表廠雖然歷經無數轉變，但卻仍然精益求精，美更求美，這也正是百余年前激勵其創始人喬治向前的一條原則。The curvature interference of the gear and the influence of radius of the mill - cutter, axial misalignment, and center distance on meshing are analyzed. based on these analyses, propose two methods to achieve point - contact : to change the radius of the mill - cutter and increase the center distance
在分析了弧齒線圓柱齒輪的嚙合傳動不產生曲率干涉的條件和刀盤展成半徑、軸線平行度誤差、中心距對嚙合影響的基礎上，提出了點接觸弧齒線圓柱齒輪實現的兩種方案:調整刀盤展成半徑和增大中心距。The rack - and - pinion steering is sharp, and the torsion beam rear axle gives the car a grown - up feel
齒條式齒輪轉向是敏銳的，而尾軸扭力梁給車子有大車的感覺。Syn - h1 - 220 ： polyalkylene glycol based synthetic chain ， bearing and gearbox lubricant *
聚合型全合成潤滑劑* ，用於鏈條，軸承和齒輪箱。分享友人