amplitude calibration 中文意思是什麼

amplitude calibration 解釋
幅度定標
  • amplitude : n. 1. 廣闊，廣大。2. 豐富，充足。3. （思想的）廣度。4. （天體出沒時偏離正東或正西的）角度距離。5. 【物，電】振幅。
  • calibration : n. 1. 測定口徑。2. 刻度，標度，劃度數。3. 校準；標準化。
  1. The amplitude control relies on the use of an calibration scheme

    鋸齒波的穩定的幅度是通過校準電路來實現的。
  2. This paper goes on with analysis of the phased array radar calibration theory and compare of different schemes, then the best is adopted. 2 mhz digital circuit mainly composed of dds ( direct digital synthesis ) chip, which carries out the shift of the phase and the limit of the amplitude, has been designed and debugged successfully. it is used to substitute for the conventional phased shift circuit and amplitude limiting circuit which work at the radio frequency, so the all - digital transmit channel of phased shift array radar is achieved

    本論文研究的重點是：針對傳統相控陣雷達系統收發（ t r ）組件中的移相和限幅功能均在射頻段完成，大膽利用直接數字合成（ dds ）晶元組成頻率在2mhz左右的數字電路代替傳統相控陣雷達在射頻段進行移相和限幅的電路，從而組成全數字發射通道，使對相位和幅度的控制和調試更方便快捷，並設計具體的電路驗證此方案的可行性。
  3. At first, the algorithms for " nose - to - nose " calibration technology acquiring the parameters are introduced, including the algorithms for acquiring the impulse response, the step response, the rise time, the amplitude response and the phase response

    首先，介紹了「 nose - to - nose 」校準技術獲取示波器沖激響應、階躍響應、過渡時間、幅頻特性和相頻特性的各種演算法。
  4. Calibration of an oscilloscope calibrator for amplitude output only

    校正一個示波器校正器的幅度輸出。
  5. Calibration of an oscilloscope calibrator for amplitude and time mark outputs

    校正一個示波器校正器的幅度及時標輸出。
  6. Aperture synthesis uses interferometry technique to improve the limitations set by antenna physical aperture while working at lower frequency. phase and amplitude calibration of the visibility samples must be carried out to compensate for system bias before measurement

    綜合孔徑技術利用了以小口徑天線陣列合成大的觀測口徑的技術，解決了在較低頻率時天線物理口徑要足夠大才能得到期望的空間解析度的嚴重缺陷。
  7. Constant amplitude dynamic force calibration - calibration and verification of non - resonant uniaxial dynamic testing systems - method

    等幅動態力校準.非共振單軸向動態檢驗系統的校準和驗證.方法
  8. Constant amplitude force calibration - calibration of the calibration device instrumentation to be used for the dynamic calibration of non - resonant uniaxial dynamic testing systems - method

    等幅力校準.非共振單軸向動態檢驗系統的動態校準用校準裝置儀器的校準.方法
  9. Results show that the saw - tooth signal amplitude oscillate within small amplitude through the calibration

    通過校準，鋸齒波的幅值變化量可控制在很小范圍內。
分享友人
分享到 Line

分享到臉書