annealed steel 中文意思是什麼
annealed steel
解釋
退火鋼-
Cold drawing annealed ground steel wire
冷拉退火磨光鋼絲 -
With plating time going on, the nano - polycrystal gathering grows in two dimensions, and the new nano - polycrystal layer appears simultaneously on the formerly formed nano - polycrystal surface. because the boundary and defect densities in quenched and tempered 45 steel is higher than those in annealed steel, the nano - polycrystal gatherings formed at its surface at the beginning of electro - deposition are more concentrated, and then their size is smaller. the microstructure of the ni - p alloy coating has closed relation with its phosphorus content with the increase of phosphorus content, the microstructure of coating turns from nano - crystalline to the amorphous
隨著施鍍時間的延長，納米晶聚晶體在橫向二維生長的同時，在納米晶聚晶體的表面上也進行著三維方向的新的一層聚晶體的生長；在調質態45鋼表面，由於其具有比較高的晶界和缺陷密度，因此在沉積初期，納米晶聚晶體的成核密度也較大，從而在二維方向聚晶體的尺度較小，鍍層沉積初期表現為緻密細小的鱗片狀組織。 -
On the surface of annealed 45 steel, as the pearlite in it contains cementite phase and has high crystal boundary density, the nucleation and growth of deposits prefer to occur at the pearlite at the beginning during depositioa the coating exists in form of nano - polycrystal layers composed by gathering of nano - sized crystals
在退火態45鋼表面，由於珠光體組織中含有滲碳體相且具有比較高的晶界密度，因而在沉積初期鍍層優先在此處形核和生長；鍍層在基體表面是以納米尺度的晶粒聚集在一起形成的聚晶體形式存在的。 -
It is fused with first - class raw materials and 3500kva furnace, used to grind metals of high - tensil strength such as steel, annealed malleable iron and hard bronze. itcan also be used as high - class refractory
棕剛玉是採用一流的原料並在3500kva冶煉爐中冶煉而成，適宜磨削抗張強度較高的金屬，如各種通用鋼材，可?鑄鐵，硬青銅等，也可用於製造高級耐火材料。 -
Specification for annealed round steel wire for general engineering springs
通用工程彈簧用退火圓鋼絲規范 -
Milling, turning, planning of cast iron, annealed cast iron, steel, austenitic steel. medium cutting speed and chip cross - sections. for interrupted cutting and varying cutting depths. high toughness and impact strength
對鑄鐵、退火鑄鐵、鋼鐵、奧氏體鐵進行銑削、車削、刨平加工的牌號。適合中等切削速度、中等切削截面的切削加工。適合不同切削深度和間斷性切割。抗沖擊強度高、韌性高。 -
Standard specification for annealed or cold - worked austenitic stainless steel sheet, strip, plate, and flat bar
退火或冷加工的奧氏體不銹鋼薄板帶材中厚板和扁棒用標準規范 -
Study on structure and texture of hot - galvanized layer of cold - rolled sheet and cold - rolled annealed sheet using if steel
鋼冷軋板和冷軋退火板熱鍍鋅層組織和織構的研究 -
Analyses showed that the effect of heat treatment is remarkable to 304 stainless steel fibers. and a new martensitic phases formed, and ms increased during annealing at 180c ; annealing above 180c decreased the ms. after annealed in the range of 380c ~ 440 c, the he increased and the product ( mr hc ) improved. it was also shown that annealing affected the mechanical properties of 316l ss fibers obviously
304不銹鋼纖維在180附近退火處理其ms略增加，其內部相變與一般的304不銹鋼體材料存在差別； 380 440區間退火處理，其矯頑力急劇增加、磁能積參數配合比較好；退火熱處理對316l不銹鋼纖維的力學性能作用明顯。 -
Annealed sheet steel
退火薄鋼板
分享友人