arrangement of holes 中文意思是什麼

arrangement of holes 解釋
鉆孔布置
  • arrangement : n. 1. 整頓，整理；排列，布置，分類。2. 〈pl. 〉安排，料理，籌備，預備。3. 商定，約定。4. 調解，和解。5. 改作，改編；改編的樂曲。
  • of : OF ＝Old French 古法語。
  • holes : 安裝孔
  1. Effects of different fuel - air ratios and different geometric parameters of dual - stage swirler ( such as inner diameters of the primary swirl and secondary swirl passages, outer diameters of the secondary swirl passages, vane angle of the primary and secondary swirler, the distance of the flare exit from throat etc ) on combustion performances are studied experimentally. the experimental results show that radial profiles of the outlet gas temperature 、 combustion efficiency 、 emissions of co2 、 co and nox and lean blowout are affected with different degrees by the different geometric parameters of dual - stage swirler and the arrangement of primary holes

    在不同油氣比下，不同的雙級旋流器幾何參數（例如:一級與二級旋流器出口內徑d 、葉片安裝角、二級旋流器出口外徑d 、二級旋流器的喉道到出口截面的距離l和喉道前後的圓弧半徑r以及主燃孔孔布局等）對單頭部環形燃燒室的出口溫度分佈、燃燒效率、貧油熄火油氣比以及污染物（ co _ 2 、 co和nox ）排放等燃燒性能的影響規律進行了研究。
  2. This paper studies on the shape and structural characters of the disc flute of air cushion rugulating machine, describes the designing and testing method of the parameters such as the diameter and arrangement of the air holes

    對氣膜調偏機盤槽形狀和結構特點進行了研究，論述了氣孔直徑及排列方式參數的設計和試驗方法。
  3. When the punched baffle is proper in length, the small holes are in staggered arrangement and the punched ratio gradually increases from the central axis to the boundary along the baffle length, the performance of flow distribution in the plate - fin heat exchanger is effectively improved by the optimum design of header configuration

    從實驗對比分析中得出，當擋板小孔呈錯排分佈、開孔率沿擋板的中軸線向兩側逐漸增加、且總開孔率達到50 %左右的時候，在相同的入口條件下，不均勻系數由原始封頭的1 . 210降至0 . 209 ，最大流速與最小流速之比由23 . 163降至1 . 756 。
  4. Firstly, for jet array impingement cooling, the effects of the distance of adjacent holes, the impinging distance and jet reynolds number on heat transfer characteristic at the target wall are summarized under staggered holes arrangement and the same hole diameter. and then, the numerical simulation of inclined multi - hole film cooling has been studied. the influence factors examined in this case include blowing ratio and the distance of adjacent holes

    首先通過對射流沖擊冷卻方式的研究，分析了相鄰孔間距、沖擊間距以及射流入口雷諾數對沖擊靶面換熱系數的影響情況，然後對多斜孔冷卻方式進行了數值模擬，重點探討了吹風比和相鄰孔間距對絕熱溫比與壁面換熱系數的影響規律，最後，針對沖擊-發散復合冷卻流場的計算物理模型，研究吹風比、相鄰孔間距的變化對沖擊-發散復合冷卻流動與傳熱特性的影響。
  5. In addition the construction method and holes arrangement of milliseconds differential blasting technology were design

    分析了微差爆破技術的施工方法和布孔，並對微差爆破的時間間隔、用藥量等參數進行了計算。
分享友人
分享到 Line

分享到臉書