beam to beam moment connection 中文意思是什麼

beam to beam moment connection 解釋
梁間剛性結合
  • beam : n 1 梁，棟梁，桁條；（船的）橫梁。2 船幅；（動物、人的）體幅。3 （秤）桿，杠桿，（織機的）卷軸，...
  • to : adv 到某種狀態；〈特指〉到停止狀態；關閉。 ★也常和動詞結合，略去其後賓語，而構成成語： The door i...
  • moment : n 1 一轉眼功夫 片刻 瞬息 剎那；時刻。2 時機 機會；場合；危機；當前。3 重要 緊要；【哲學】要素 契...
  • connection : n. 〈美國〉＝connexion.
  1. From the analysis, some suggestion about joint rigidity design is put forward : 1. joint initial rigidity can be enhanced within the limited range when to increase end - plate thickness ; 2. the rigidity and ultimate moment can be enhanced obviously when to adopt the beam with inclined section or to add axilla at the connections between beam and column ; 3. withm the permissive construction condition, exteriorly extended end - plate inclinedly placed is suggested to be applied firstly ; 4. when the rate of joint rigidity to beam rigidity, that is called, is less than 0. 1, the joints can be regarded as zero - rigidity joints ; on the other hand, if is more than 26, it is rigid connection joints

    採用斜截面梁並在樑柱交接處局部加腋能明顯提高節點剛度和梁的抗彎能力； 3在允許的施工條件下，應優先採用外伸式端板斜放節點，有利於提高節點剛度，進而提高節點的抗彎能力； 4節點剛度與其連接構件的剛度比值0 . 1時，可按鉸接節點設計； 26時，可按剛接節點設計。
  2. Two hypothesises, different from the traditional viewpoints, about stress distribution in beam section at the connection of beam and end - plate are presented by author to determine the ultimate moment of end - plate connection

    其計算過程分為兩步： （ 1 ）計算梁受拉翼緣的極限拉力； （ 2 ）計算端板連接的極限彎矩。
  3. After comparing between the finite - element analysis and experimental results, the author verified the fem. then according to the chinese code, the nonlinear finite model of the beam - to - column is established which are made of different size components. the responses of beam - to - column web moment connections which are made of different size components are compared and analyzed from three facets, and the conclusions about the joints behavior are drawn : thicken the connection plate, lengthen the connection plate or use a back - up stiffer can improve the connection behavior, consist of improving the behavior of load - supported and reducing the stress convergence in the flange moment plates

    本文根據我國規范的有關規定，自行建立了12個不同構件尺寸的樑柱腹板連接的三維有限元模型，對不同構件尺寸的樑柱腹板剛性連接節點在單向荷載作用下的反應進行了研究，從結構的mises應力等值線示意圖、梁端加載處的荷載? ?位移曲線、翼緣連接板兩端的mises等效應力以及翼緣連接板與柱相連接的三邊的mises應力等值線示意圖四方面進行了比較與分析，從而得出了不同構件尺寸的樑柱腹板剛性連接的在受力行為上的結論：增加翼緣連接板的厚度、增加翼緣連接板的長度以及採用柱的橫向加勁肋均可以改善節點的受力性能：提高節點的承載能力；減小翼緣連接板內部與柱翼緣邊的的應力不均勻現象，從而避免試件過早地發生破壞。
分享友人
分享到 Line

分享到臉書