bonding length 中文意思是什麼
bonding length
解釋
接合長度-
Fabrication process of the microgripper based on silicon bulk micromachining is designed. effects of footing and lag in icp and bonding failure are discussed as emphases. the cantilever type gripping finger that is 6 m wide and 5471 m in equivalent length was released successfully characteristic of comb - drive electrostatically actuated microgripper is tested
進行了大量的工藝試驗和分析，特別對大深寬比的超長長度懸臂梁型夾持臂及梳狀驅動結構進行了深入研究，解決了微細加工工藝中的關鍵技術。 -
The strength of fibre - matrix interfacial bonding affects the overall composite strength and mode of failure, and the critical fibre length
界面壓焊影響總力和失敗模式，及有關纖體長度的纖維基的力。 -
The urea - formaldehyde ( uf ) polymer / sio2 composite microspheres were prepared by polymerization - induced colloid aggregation ( pica ) method. the formation mechanism of composite microspheres is attributed to the fact that that urea and formaldehyde firstly undergo acid - catalyzed polymerization to form oligomers, and then the sol particles are adsorbed on the chain of oligomers by wan der walls force and hydrogen bonding. when the oligomers reach the critical chain length, they separate from solution due to phase separation
對復合微球形成機理的研究表明，尿素和甲醛在酸性條件下自身聚合可以形成高分子微球，在sio _ 2酸性溶膠中發生聚和反應時，隨著反應的進行，齊聚物不斷生成， sio _ 2膠體顆粒逐漸吸附在齊聚物分子鏈上，當聚合物鏈達到沉澱臨界鏈長時，由於相分離作用，從前驅物溶液中析出，同時sio _ 2膠體顆粒均勻的分佈在脲醛聚合物網路中，隨之沉澱出來，形成脲醛sio _ 2復合微球。 -
Regarding the rc beams subjected to concentrated load or even load and braced by bonding steel, an analysis is made on the relevant factors influencing maximum anchorage shear stress of steel sheet. the analysis is based on elastic theory and makes use of the formula for calculating anchorage shear stress of steel sheet. as indicated by the results, the maximum anchorage shear stress not only realtes to such parameters as height of cross section of rc beam and span but also relates to the thickness of adhesive layer, elastic modulus, thickness of steel sheet, and length of steel sheet. the present method will check maximum an chorage shear stress on the end of shear sheet so as to prevent rc beam from local damage. the present results will offer important reference for our country to further perfect bracing design by bonding steel method
在彈性理論的基礎上，利用鋼板錨固剪應力計算公式，對在集中荷載或均布荷載作用下採用粘鋼加固的混凝土梁，分析鋼板錨固最大剪應力的有關影響因數.結果表明，最大錨固剪應力不但和混凝土梁的截面高度、跨度等參數有關，還和粘膠層厚度、彈性模量、鋼板厚度及鋼板長度有關.採用文中方法可以對鋼板端部最大錨固剪應力進行驗算，防止混凝土梁出現局部受拉破壞.研究結果為進一步完善我國粘鋼法加固設計提供重要的參考資料 -
Influences of axis inclination, length, clamping angle of anchorage, roughness and bonding degree of interface on the displacement of anchorage and repose stability of rock mass were explored
就錨碇體軸線傾角、長度、夾持角、接觸界面粗糙度及結合程度對錨碇位移和巖體安息穩定性的影響作了深入探討。 -
Pull - out test of flexible macro - fiber is conducted firstly, this paper is emphasized effects of fiber embedded length, cured times and matrix strength on bonding strength between synthetic macro - fiber and mortar
本論文首次完成了柔性粗纖維的拉拔試驗，重點研究了纖維埋置長度、養護齡期、基體強度對粗合成纖維-砂漿基體界面粘結強度的影響。 -
The criterion of microroughness for self - propagating wafer bonding is studied according to jkr contact theory, where the microroughness model is based on a sinusoidal distribution for gap height and gap length
摘要根據jkr接觸理論，推導出晶片直接鍵合時晶片接觸表面粗糙度需要滿足的條件，其中晶片接觸表面粗糙度的描述是基於縫隙長度和縫隙高度的正弦波模型。
分享友人