brush contact 中文意思是什麼
brush contact
解釋
電刷觸點-
We are looking for carbon brush, if you can supply, please contact us
我們正在尋找汽車碳刷，請供應商聯系我們 -
Position the fuser film sleeve into heater, and the end of the film with ground ring should be in good contact with the conductive rubber gear of pressure roller or the conductive brush after installation
請在安裝新定影膜前，在塑料架與定影膜接觸的部位均勻塗上硅脂，盡量在有棱的地方多塗點，以保證定影膜與塑料架的充分潤滑。 -
The thesis mainly contains : we analyze the brush seal ' s structure. based on the reasonable assumption, a new three - dimensional fea ( finite element analysis ) model is put forward in contact pressure calculation of brush seals
論文的主要內容包括：分析了刷式密封的結構特點，在對其中一些因素進行了合理簡化的前提下，提出了一種新的針對刷式密封接觸壓強的三維有限元計算模型。 -
The traditional ag / graphite electrical brush is a kind of excellent electrical contact material. with the increase of the content of graphite, though the properties of lubrication may be increased, the properties of mechanical and electrical are linear decrease. the applications will be very difficulty in complicated environment
傳統銀-石墨電刷材料是一種很好的電接觸材料，但隨著石墨含量的增加，雖然潤滑性能增加但其相對密度、硬度、導電性能都直線下降，已很難滿足現在各種復雜情況下的應用，因此需要採用一種新的方法或材料來代替石墨，即起到潤滑的作用又可增強、導電導熱。 -
Results are presented showing the influence of original interference between bristles and shaft, differential pressure, bristles " rows and slope on the contact pressure. the contact pressure can be calculated by bp arithmetic of nerve net on matlab successfully. based on brush seals wear theory and the given solid wear equation, the wear and longevity equation of brush seal are set up
根據刷式密封磨損機理和特點，利用已有的固體磨損公式，建立了刷式密封磨損量的計算公式，推導出刷式密封磨損壽命的理論計算公式，並在不同的實際工況參數條件下進行了相應的磨損壽命計算。 -
It brings out a kind of simplified three - dimensional model in the contact analysis. then combined with ansys software, the contact of brush seal is analyzed wholly, and the longevity ' s equation of seals is derived from the calculation. from the analytic results, we can get the longevity related to parameters
首先提出一種用於刷式密封接觸分析的三維簡化模型，然後利用有限元分析軟體ansys對刷式密封進行了較完整的接觸分析計算，推導出計算刷式密封磨損壽命的理論公式，利用獲得的分析結果計算出與刷式密封工況參數相關的磨損壽命。 -
Brush contact loss
電刷接觸損耗 -
Djw - wb 、 sjw - wb series single and three phase & large - power auto compensated voltage regulator, incorporating advanced technology of group winding compensation and mon - contact suitch and micro - computer controling ac regulation, with functions of high effeciancy quick regulating ou - to - balance of three phases no mechanical no mechanical broken down and wear of carbon brush and time delay over and low load warning and protection
集先進的組合繞組補償方式和無觸點開關、微機控制交流穩壓技術於一體，具有高效節能、調節快速、三相自動平衡、無機械故障和碳刷磨損，並具有延時，過、欠壓報警和保護等功能。 -
In contrast to the broken lines painted by conventional brush contact, pollock had developed a technique in which he poured a constant stream of paint onto horizontal canvases to produce uniquely continuous trajectories
傳統筆觸是一條條斷開的線，對照之下，帕洛克發展出一種技巧，能夠源源不絕將油彩傾?在橫展的畫布上，從而創造出獨特的連續軌線。
分享友人