component deformation 中文意思是什麼

component deformation 解釋
部分變形
  • component : adj 構成的，組成的，合成的，成分的。 component motion 【物理學】分運動。 component part 組成部分...
  • deformation : 變形,走樣
  1. This paper elementarily collects the anomalies of coseismic and post - seismic effect such as seismic activity, crustal deformation and underground liquid and so on observed in china ' s mainland, which include the evident seismic activity ( especially in yunnan ) increase, obvious crustal deformation, such as the abnormal variation of crustal stress and strain in bore volumetric deformeter and the remarkable change of underground temperature, the chemical component, especially the underground water level

    初步匯集了在中國陸區觀測到的地震活動、地殼形變、地下流體等多學科震時和震後效應的異常變化，包括地震活動性（特別是雲南地區）的顯著增強；地殼形變觀測，尤其是鉆孔應變觀測記錄到地殼應力應變的震時和震后顯著變化，以及地下水溫度、化學成分、特別是水位的突出變化。
  2. Abstract : according to the deformation or fracture caused by uneven loads on the structural connection, the smart structure with sensible and regulative functions has been proposed to be used in bolt groups. the smart structure is constituted with the auto - even - load connecting component made of the shape memory alloy material. the mechanical behavior of the auto - even - load component in the bolt groups is analyszed. its auto - even - load and the regulative principle to prevent the fracture are also studied

    文摘:本文針對結構聯接受力不均易產生變形或破裂等問題，提出了在螺栓組中加裝由形狀記憶合金材料製作的自動均載傳力件構成具有感知和調節功能的智能結構，並對螺栓組聯接加裝均載傳力件后的均載防斷功能進行了力學特性分析，特別是對螺栓組傳力件自動均載和防斷的調節原理進行了研究，最後進行了實驗驗證。
  3. Research on mechanism of deformation and destruction in deep component roof

    深部復合頂板巷道變形破壞機理研究
  4. Machining deformation of aircraft monolithic component is simulated by finite element method ( fem ) and validated by experiment. the initial residual stress in pre - stretched plate is generated by simulating quenching and stretching processes. with a single tool - tooth milling process fem, the machining loads in monolithic component material removing is obtained. restart - calculation is put forward to complete the whole simulation of machining process. to verify the fem result, an experiment is carried out. the deformation distribution of the monolithic component resulting from fem shows a good agreement with the experiment result, which indicates that the key technologies presented in the paper are practicable and can be used to simulate the milling process of monolithic component to predict its deformation. lengthy and expensive trial and error experiment process can be avoided

    在模擬淬火、拉伸過程獲得含有初始殘余應力的預拉伸板材以及模擬單齒切削過程獲得切削載荷的基礎上，提出並採用接力演算法，對一航空整體結構件的材料銑削過程進行有限元模擬，同時進行了試驗研究.結果表明，有限元模擬的整體結構件的變形與試驗具有一致性，從而證明提出的整體結構件加工模擬關鍵技術的可行性，避免了為研究加工變形而進行的繁瑣的試錯法
  5. In the paper, in accordance with the thermal power torpedo propulsion system using hap tri - component fuel, with the i - deas software, applying the cad technology and the fem, the research of simulation on the piston - one of key parts of engine was proceeded and the paper presented the whole analysis process of the piston including thermal analysis. in the paper, the question of the boundary condition in the complicated engineering was explored and the temperature field. the stress field and the deformation of the piston were computed and analyzed under a new kind of fuel ( hap )

    本文針對三組元魚雷熱動力系統，應用i - deas軟體，利用cad技術和三維有限元方法（ fem ） ，對發動機的關鍵零件? ?活塞展開模擬研究，對活塞進行了包括熱分析在內的全過程的模擬計算，探索了復雜工程中邊界條件的處理問題，分析計算了魚雷發動機活塞在新型燃料（三組元燃料）工作下的穩態溫度場、應力場與變形情況，最後，根據分析結果對其結構提出了改進意見。
  6. Bending deformation ： the component bends in one side after welding

    彎曲變形：構件焊后朝一側彎曲的變形。
  7. Transverse / cross / lateral contraction deformation ： the component contracts in the upright direction of weld after weiding

    橫向收縮變形：構件焊后在垂直焊縫方向上發生的收縮。
  8. 5. software designing about planetary - gear transmission. it consists of calculation of equivalent error of the averaged load component, force and deformation analysis of component, contact stress and bending strength analysis. 6

    用vb6 . 0自行開發了行星變速箱計算機輔助分析程序設計，該分析程序主要功能包括均載件的等效誤差、各部件的受力及變形分析及齒輪彎曲強度及接觸強度校核6
  9. The compliant mechanism is a kind of new typed mechanism that uses the elastic deformation of component itself to accomplish the transmission of movement and force and possesses numerous advantages of light quality, less friction etc., thus caused wide attention of scholars both at home and abroad

    摘要柔順機構是利用構件自身的彈性變形來完成運動和力的傳遞與轉換的新型機構，具有質量輕、摩擦小等眾多優點，引起了國內外學者的廣泛關注。
  10. Finite element analysis of large deformation of compressed rubber component

    壓縮狀態下橡膠件大變形有限元分析
  11. Then, on the basis of the simplified yielding model of active beam link, which is the key component of ebsf, the deformation mechanism and geometry relation equation under different kinds of loads are analyzed, and then the ideal yielding mechanism of ebsf is proposed

    然後從該結構中的最關鍵構件- - -耗能梁段的簡化屈服模型入手，研究其在外荷載作用下的變形機制及幾何關系式，並由此提出了耗能梁段的較理想的屈服機制。
  12. Longitudinal contraction deformation ： the component contracts in the weld direction after weiding

    縱向收縮變形：構件焊后在焊縫方向上發生的收縮。
  13. Reducing partial rigidity : when closed weld or the weld which has less rigidity are welded, we can take anti - deformation way to reduce the partial rigidity of component

    降低局部剛性：焊接封閉焊縫或其剛性較大的焊縫時，可以採取反變形法來降低結構的局部剛性。
  14. 2. force and deformation analysis of component of bs305 planetary - gear transmission are proposed as well as gear contact stress analysis. the factors that cause normal and abnormal axial force and their extent are proposed also

    2 .對bs305行星變速箱各部件的受力及變形以及齒輪接觸應力進行分析；分析了引起正常軸向力及異常軸向力的各種因素和影響程度。
  15. Involving interaction of gasket, bolts and flange rings, the load - deformation and the structural fuzzy reliability of each component are analyzed in the case of ideality, external loads and creep - relaxation respectively. and then, the sealing fuzzy reliability of the flanged connection system is researched. the function of each part of genetic algorithm is analyzed in application to nonlinear unconstrained and constrained optimization

    本文將墊片、螺栓和法蘭作為一個相互作用的整體，比較深入地分析了理想情況下、有外載作用及蠕變-鬆弛影響下，平墊片和0形圈這兩種典型的火箭發動機法蘭連接系統各元件的載荷與變形、元件的結構可靠度和火箭發動機法蘭系統的密封可靠度。
  16. According to the time - varying behavior of concrete dam ' s deformation, the water pressure component is established considering the time - varying action and the temperature component is established by the integration regression method

    摘要針對混凝土壩變形的時變特性，構建了考慮時變作用的壩體水壓分量，採用積分回歸法建立了溫度分量。
  17. Data processing in elliptic construction component deformation surveying

    橢圓形構件變形測量的數據處理
分享友人
分享到 Line

分享到臉書