corner crack 中文意思是什麼
corner crack
解釋
通孔斷角拐角裂縫-
The main research is below : ( 1 ) the influence to intensity and rigid with corner angle ( 60, 75 and 90 degree ) of crack and the board axes ( 2 ) do a fem stress / strain and crack growth simulation analysis when the corner angle of crack and the board axes is 60 degree ( 3 ) do a intensity resume analysis for the structure which is repaired with a titanium patch in a mechanical way when the corner angle of crack and the board axes is 60 degree through simulation analysis for three failure criterion, we have : ( 1 ) in 60, damage extend quickly with damage analysis in hashin criterion ; it is slower for analysis in maximum stress or hashin - rotem criterion. ( 2 ) in special term ( physical condition incision, shape or maximum load ) the compression strength of the stiffened plate will decline 45 % ~ 50 % under compression loads
通過採用三個不同損傷判據的數值模擬模擬，得到如下結論： （ 1 ）在60時，用hashin判據進行的損傷分析，損傷擴展較快；最大應力及hashin - rotem判據進行的損傷分析，損傷擴展基本相當，且較慢； （ 2 ）在所給加筋板的物理條件、切口大小及形狀、最大載荷等一定的條件下，該加筋板在壓縮載荷作用下，其壓縮強度下降了45 50 ； （ 3 ）在本文提及到的機械連接修理方法以及載荷條件下，修理后的結構強度恢復能夠滿足戰時要求。 -
The main results and academic contributions of the dissertation can be summarized as following : 1 ) for the difficulty to obtain the accurate analytical solution of the stress constraints around 3d cracks, detailed 3d fe analyses have been conducted to study the out - of - plane constraint factor tz around a straight through - thickness crack, a quarter - elliptical corner crack and a semi - elliptical crack embedded in an isotropic elastic plate subjected to uniform remote tension loading. the distributions of tz are minutely studied in the forward section of the cracks. strong 3d zones ( tz > 0 ) along the crack front were investigated despite the far field stress - free boundary conditions
全文主要研究內容和學術貢獻如下: 1 .針對一般三維裂紋端部場應力約束準確解析的困難，對均勻拉伸載荷作用下各向同性彈性板中穿透厚度中心直裂紋、半橢圓表面裂紋和1 / 4橢圓角裂紋進行了大量詳細的全場應力三維有限元分析，首次全面分析了非穿透裂紋端部場三維影響區范圍，給出了不同形狀三維裂紋前沿離面應力約束因子tz的數值解，並結合k場平面解給出了非穿透裂紋端部應力場k - tz雙參數描述。 -
A segment of the box corner was removed with a hole saw in order to permit an examination of the crack.
為了對裂紋進行檢查，用圓孔鋸從箱型斷面拐角處鋸下一部分。 -
Eigenequation about singularity, singular stress fields and electrical displacement fields near the interface edge are obtained under axisymmetric distortion. finally, a special finite element formulation which is based on the principle of minimum potential energy has been developed for determining the orders of the singularity of the singular stress fields around the singular point ( interface edge, interface corner and the interface crack ) in the bonded dissimilar anisotropic / anisotropic, piezoelectric / piezoelectric as well as piezoelectric / anisotropic materials. the numerical results show that this method is very convenient and efficient
最後，從最小勢能原理出發，在僅僅考慮奇異性支配區域這一前提下，對于彈性接合材料的平面變形問題和擬平面應變問題，以奇異點為原點分別建立極坐標系和圓柱坐標系，通過分部積分消除廠項，從而使奇異性問題的求解由原來的二維降為一維；對於三維變形問題，以奇異點為原點建立球坐標系，通過分部積分消除項，從而使奇異性問題的求解由原來的三維降為二維。
分享友人