deviation axis 中文意思是什麼

deviation axis 解釋
軸偏向
  • deviation : n 1 脫離,越軌,背離 (from) 。2 偏向,偏差。3 (統計上的)誤差。4 【航海】(故意)偏航。5 【數...
  • axis : n ( pl axes )1 軸,軸線。2 【植物;植物學】莖軸。3 【解剖學】第二頸椎,第二脊骨。4 【政治學】軸...
  1. ( 2 ) the correction results by the new and old methods are the same when the axis system deviation is small, while the monomial error accumulating totals correction method is practical only when the surveying angles and deviation are both small

    ( 2 )當軸系偏差較小時,用新舊兩種方法修正結果一致。單項差累計改正法只適用於測量角和偏差都很小的情況。
  2. This type of joint have been widelu used in the steel pipeline system for connection, it has a very good self - compensation performance while temperature change and angle deviation of the pipeline axis

    鍛壓卡箍式柔性管道接頭該產品具有溫度自補償和角度自補償功能,是鋼制管道系統中廣泛應用的聯接件,其結構合理、耐壓強度高、密封性能好,安裝維修方便。
  3. On such a basisthe commonly used monomial error accumulating totals correction method is introduced. the author proposes a coordinate transformation method to deal with its drawbacks of maths model imperfection, not applicable to lange - angle deviation and adding to the difficulties of equipment. while orientating the order of matrices according to the principle of the accordance between coordinate ' s rotating order and the physical process of device measuring, a strict maths model of the influence of axis system deviation on surveying angles is concluded and the corresponding correction method is induced. its far - reaching meanings are as follow : ( 1 ) the maths model of the influence of axis system deviation on surveying angles established by the new method is concluded after considerations for the three deviations simultaneously. changes under all circumstances are included, so it is theoretically a perfection of maths method

    在此基礎上介紹了國內目前採用的軸系偏差對測量角影響的經典改正方法?單項差累計改正法,並針對該方法存在的數學模型不完善、對大角度偏差不適用、增加設備調整難度等缺陷,提出採用坐標變換方法,並根據坐標的旋轉次序與設備測量的物理過程相符合的原理定位各矩陣的先後順序,推導出了軸系偏差對測量角影響的嚴格數學模型,歸納建立了相應測量角的改正方法。
  4. Left axis deviation

    軸左偏心電圖
  5. The engineering algorithm ( physics optical method ) for numerical simulation of ao effect was also derived, the point - diffusion function obtained can be used to obtain sighting - axis deviation, blurring, jitter and strehl ratio, so that the ground simulation of ao effect can be theoretically feasible

    同時推導了氣動光學效應數值模擬的工程演算法(物理光學法) ,得出的點擴散函數便可得到氣動光學效應的視軸偏差、模糊、抖動、 strehi比等,從而使氣動光學的地面模擬測試研究在理論上可行。
  6. The equipment is also widely used in motor vehicles and test center ( field station, line ), the manufacturing plant, maintenance industries, transportation companies and fleet of motor vehicle headlamps on the luminous intensity and volume of optical axis deviation was detected, adjustments

    該儀器廣泛使用於機動車檢測中心(場、站、線) 、製造廠、維修行業、運輸公司和車隊,對各種機動車前照燈的發光強度和光軸偏斜量進行檢測、調整。
  7. Glass containers - vertical axis deviation of bottles test methods

    玻璃容器-玻璃瓶垂直軸偏差測試方法
  8. The author first explains that large - scale measurement device is one of the most basic measuring methods of obtaining external trajectory data and flight status. lt is pointed out that the accurateness of the main - item axis system deviation correction ( including vertical, level and collimating axis deviation ) of large - scale measurement device error is of critical importance to the precison of measuring device ' s surveying angles. to improve its precison, the influence of axis system deviation on surveying angles must be corrected

    首先說明了在現代航天靶場中,大型測量設備是獲取外彈道數據和飛行狀態的最基本的測量手段之一,指出大型測量設備測量系統誤差的主項軸系偏差(包括垂直軸偏差、水平軸偏差和照準軸偏差)改正的精確與否直接關繫到測量設備的測角精度,因此要提高測量設備的測角精度,必須對軸系偏差對測量角的影響進行改正。
  9. Glass containers - vertical axis deviation of bottlestest methods

    玻璃瓶垂直軸偏差測試方法
  10. But considering the influence of artillery goal mensuration, computer calculate and artillery following system, the axis of artillery pipe and goal have deviation, this error is dynamic tracking error

    但由於火炮目標測定器、計算機解算、火炮隨動系統等環節的影響,火炮身管的軸線與目標存在偏差,該項誤差即為動態跟蹤誤差。
分享友人