dynamic force analysis 中文意思是什麼

dynamic force analysis 解釋
動力分析
  • dynamic : adj 1 動力的，動力學的；力學（上）的；動（態）的；起動的。2 有力的，有生氣的；能動的；（工作）效...
  • force : n 1 力，勢。2 體力，氣力，精力，魄力。3 暴力，壓力；兵力，武力。4 〈pl 〉 部隊，軍隊，兵力。5 勢...
  • analysis : n. （pl. -ses ）1. 分解，分析；【數學】解析。2. 梗概，要略。3. 〈美國〉用精神分析法治療（＝ psychoanalysis）。
  1. The dispassion of the total input earthquake energy is also investigated. through the study on the restoring - force model of isolation systems and on the nonlinear seismic response of base - isolated structures, the program of dynamic analysis of base - isolated structures ( dabis ) is worked out. detailed analysis on

    綜上所述，通過對隔震系統恢復力模型及基礎隔震結構非線性地震反應分析的研究，編制了可用於工程實際計算的基礎隔震結構動力分析程序，對基礎隔震結構多維地震反應及平一扭禍聯地震反應進行了較為詳盡的分析，完善和發展了基礎隔震結構分析理論和計算方法。
  2. Manipulate mechanism with concentrative link lever has important significance to improve maneuverability of bulldozer currently. this thesis includes : designing manipulate mechanism with concentrative link lever and simply calculating force and displacement for operation, based on the referring existing manipulate mechanism of bulldozer ; using high - grade 3 - dimensional plotting software ug ( unigraphics ) to sculpt ; using adams ( automatic dynamic analysis of mechanical systems ) to establish virtual prototyping model and do kinematic simulation. the results verify the rationality of this mechanism and provide the basis for trial - manufacture of physical prototyping and betterment design

    本文做的主要工作是：參考推土機原有的變速轉向操縱機構，設計了集中連桿操縱機構並進行操縱力和操縱行程的簡單計算；使用高檔三維造型軟體ug （全稱unigraphics ）進行推土機集中連桿操縱機構的造型設計；應用機械繫統運動學/動力學模擬分析軟體adams （ automaticdynamicanalysisofmechanicalsystems ）對所設計的機構建立虛擬樣機，並進行運動學模擬分析，驗證了機構設計的合理性，為物理樣機的試制和改進設計提供了依據。
  3. Considering special form of the boiler frame, the reconstruction and enforcement method, in addition dynamic analysis are given by particular steps : establishment of the model of boiler steel frame, determination of earthquake loads and distribution form, and anti - side force system for the frame to model and analyze, involving loads on the frame and above it, earthquake loads, damping, sway control installation, hanging bar and plate beam

    考慮鍋爐構架鋼結構的特殊形式，研究並提出了電站鍋爐鋼結構改造加固研究方法，及動力分析的具體步驟：建立了鍋爐鋼結構動力分析模型、地震荷載分析方法、建立了鍋爐鋼結構布置型式、及整個鍋爐鋼構架抗側力體系模擬分析方法。具體包括：鋼構架本體及構架上荷載、地震載荷與阻尼系數確定、制晃裝置確定、吊桿與大板梁簡化。
  4. Presents the model proposed for analyzing the vibration characteristics of shrouded blades and their calculation method by employing a wave propagation theory and modal synthesis technology coupled with a finite element method from the view point it is possible not only to conduct frequency modulation of the shrouded blades of a gas turbine, but also to utilize the friction effects between them to dissipate energy, thereby attaining the aim of vibration alleviation, as shrouded blades have been widely used in the design of high - speed turbomachinery, such as modern gas turbines and steam turbines, and with the shrouded blades forming an integral whole in a centrifugal force field, the vibration characteristics of the whole ring of blades are different from those of a single isolated blade, and this makes it essential to take into account the integral effect of blade shrouds, concludes from the calculation examples and engineering application that the above approach is valid and correct along with the possibility of considerably reducing the scale of calculation and analysis, and points out it is necessary to take into consideration the coupled effect of the whole ring of blades while the dynamic characteristics of shrouded blades is being analysed

    帶冠葉片不但能調頻，還可以利用葉冠之間的摩擦效應來耗散能量，達到減振的目的.帶冠葉片在離心力場中形成一整體，其整圈葉片振動特性不同於單個孤立葉片，需考慮葉冠的整體效應.利用帶冠葉片系統的循環對稱性，提出了採用波傳播理論和模態綜合技術，結合有限元方法研究燃氣輪機帶冠葉片振動特性的分析模型和計算方法.算例和工程應用證明了該方法是效性的、正確的，並可以大大降低計算分析規模.研究表明帶冠葉片動力特性分析時必須考慮整圈葉片的耦合效應
  5. Solid model of the involute worm gearing solid model with drive ratio 1 / 50 is built by using ideas - 5. 0, then the elastic contact analysis is proceeded on the basis of contact fem. the dynamic evolution image of the area of the contact zone, the load sharing among instantaneous meshing tooth pairs, the distribution of the contact force, and tooth stress are obtained. 3

    通過漸開線圓柱蝸桿、蝸輪的齒面方程式，利用ideas - 5 . 0軟體建立了傳動比為1 / 50的漸開線圓柱蝸桿傳動的實體幾何模型，在此基礎上應用接觸有限元方法對該傳動進行了彈性接觸分析，包括接觸區的形狀、位置、載荷在瞬時嚙合齒對的分配狀況； 3
  6. Analysis of dynamic change and driving force of cultivated land quantity in duolun county of inner mongolia

    內蒙古多倫縣耕地數量動態變化及驅動因子分析
  7. The correlated degree of the density of deformed and failured masses and correlative dynamic force factors in tiger - leaping gorge reach are analyzed by effect measure analysis method which combines qualitative and quantitative analysis, and the key dynamic factors of bank - slope stability are established, which can provided the scientific information for origin division, evaluation, prevention of geological hazards and project planning

    本文採用定性與定量相結合的效果測度分析方法，對虎跳峽河段岸坡變形破壞密度與相關動力因子進行關聯度量化分析，從而確定了影響岸坡穩定的關鍵性動力因子，可為水電開發中的岸坡災害成因類型劃分、危險性評價、災害治理和工程規劃設計等提供科學依據。
  8. According to the elaborate analysis on friction at home and abroad, a dynamic friction compensation method is proposed to compensate the system ’ s friction force at low velocity. a dynamic friction model is build and a friction observer is designed for ordinary position servo system

    在對國內外研究現狀進行深入分析的基礎上，提出了系統低速運行時摩擦力的動態補償方法，並針對常見的電液位置伺服系統建立摩擦模型、設計摩擦觀測器。
  9. First, the dynamic stability of braid composite cylindrical shells with the influences of some main factors is introduced. the general governing equations for the nonlinear dynamic stability is obtained. by the hamilton principle. the creep buckling analysis of braid composite cylindrical shells under axial compression and the dynamic stability under nonconservation force are discussed as emphases. in creep buckling question, by means of theoretical analysis, the instaneous critical load and durable critical load of viscoelastic braid composite cylindrical shell under axial compression are obtained and the numerical example is given

    首先介紹了編織復合材料圓柱殼在幾種主要因素影響下的動力穩定性問題，用hamilton原理建立非線性動力穩定性問題的一般性基本方程。然後重點討論了編織復合材料圓柱殼軸壓下的蠕變屈曲問題及非保守力作用下的屈曲問題。對蠕變屈曲問題，通過理論分析來得到了編織復合材料圓柱殼的瞬時彈性臨界載荷和持久臨界載荷，給出了具體的算例。
  10. Based on vibration principle, the paper establishes dynamics analysis model of output shaft with elastic support, according to fourer series spread principle of periodic function, the dynamic response formula is derived by separating complex vibration force into sum of many simple harmonic excitation function of whole number times frequency relations. the result shows that response of both sides support is synchronous when load distribution non - uniform coefficient is 1

    依據振動理論建立了具有彈性支撐的輸出軸的動力學分析模型，根據周期函數的傅里葉級數展開原理，將復雜的激振力分解成為多個頻率成整倍數關系的簡諧激勵函數，導出了動態響應表達式，結果表明，當載荷分配不均勻系數為1 . 0時的輸出軸兩端支撐同步。
  11. The method is described as follows : the velocity of the moving part and the gas chamber pressure were measured with a dynamic test measurement system ; a dynamic model was built on force analysis of the moving part ; the total kinetic resistance replaced the horizontal friction and water resistance ; then the resistance - velocity relation curves at moving stages were obtained ; with the empirical formula of the gas chamber pressure and the resistance - velocity relation curves, the preliminary dynamic characteristics were analyzed and the structural form and key parameters of an underwater assault rifle were determined

    具體方法為：由動力學測量系統測得活動件速度和氣室壓力；分析活動件的受力，建立動力學模型；以運動總阻力代替水平方向上的摩擦阻力和水阻力，獲得各運動階段的阻力速度關系曲線；利用氣室壓力經驗公式和阻力速度關系曲線，對水下突擊步槍進行初步的動力學分析，確定其構造型式及主要參數。
  12. Abstract : based on the analysis of pipe ramming procedure, thi s paper presented the method calculating the ramming resistance force according to the results of strata pressure and dynamic probing, and the method calculating displacement, li mit length of rammed pipe and max. pressure inside pipe according to wave dynami cs

    文摘:分析了夯管錘夯入鋼管的過程，提出了依據地層壓力和動力觸探結果計算夯入鋼管阻力的方法；還提出了應用波動力學計算夯入鋼管位移、極限鋼管夯入長度及鋼管內最大壓應力的方法。
  13. In chapter 4, the model - building principle and calculating method of finite element dynamic analysis for large - sized assembled structure are discussed. the substructure model for hydropower house vibration analysis is established to obtain precise modal of generator floor. the harmonic vibration assumption is adopted to calculate house structure ' s dynamic response from hydraulic excitation force of hydraulic turbine generator unit

    第四章討論了大型組合結構有限元動力分析的建模原則和計算方法，建立水電站廠房振動分析的下部結構模型，對巖灘廠房進行整體模態分析，較準確地得出發電機層樓板自振特性；同時引進簡諧振動假定，迸行了機組水力振動作用下的廠房結構的動力響應分析。
  14. According to the dynamic analysis and optimization program which applys softwire visual basic 6. 0 and matlab 6. 0, this paper also stimulates the whole process and the calculation results including force, displace are all shown with two - dimension and three - dimension graphics

    同時在對帶式輸送機系統進行動態分析和優化的過程中，選用visualbasic6 0和matlab6 0編程，對系統進行動態模擬，並用二維和三維圖形對輸出數據進行顯示，使其結果更加直觀。
  15. B ) equivalent circuit method and finite element analysis ( fea ) to compute the static force are presented, the results obtained by each method are compared one with the other. c ) the results of dynamic simulation by means of the software, ansoft show the hlfm " s characteristics when the motor works in the special frequency and single stroke and the conditions used for position control. d ) the measured static thrust - displacement characteristics and the dynamic characteristics during starting show good correlation with the calculated results

    在設計並製作了實驗樣機的基礎上所做的研究內容包括； （ 1 ）分別用能量法和麥克斯韋張量法推導電磁力的計算公式，並討論他們的不同應用范圍； （ 2 ）分別用等效磁路法和有限元法作直線力電機的靜特性分析，並比較分析它們的計算結果； （ 3 ）用有限元模擬軟體做直線力電機動態特性的模擬，分別分析直線力電機的頻率特性、動子開合閘特性和開環位置控制的工作特性； （ 4 ）做直線力電機的靜推力?位移特性實驗和動子開合閘的動態實驗，並將實驗結果與計算結果進行對比，實驗驗證了計算模型及計算方法的正確性。
  16. The modal parameters are the basic data for structure dynamic analysis and vibration control. the methods of modal parameters identification can be cataloged into phase resonance testing ( normal - mode force appropriation ) and phase separation approaches

    目前，識別模態參數的方法可分為相位共振法（適調多點激振法）和相位分離法兩種[ 1 ] 。
  17. Chapter two constructed the mathematical model of robot and its environment solved by the fem analysis. the functions or relations between the robotic parameters and its drive forces, thickness or its velocities were given, and also the functions or relations between the environment and the robot force, friction, robot velocity, minimum thickness of film or sustain force of dynamic films were given

    論文第二章通過建立機器人和環境的數學模型，利用有限元方法求解其中的n - s方程，得出管道中微型機器人的各種設計參數與機器人的驅動力、形成的最小潤滑油膜厚度和機器人的運行速度之間的關系曲線，研究了管道環境與機器人驅動力、摩擦阻力矩、機器人運行速度、形成的最小潤滑油膜厚度、油膜的承載能力之間的關系。
  18. Stability of seismic resistance and dynamic response analysis for ash dams. by psedo - static analysis and seismic dynamic response analysis with fem, safety coefficient under designed seismic force, stress, strain and acceleration amplification factor have been provided. based on upper analysis, related computing program has been provided. by applying it to the ash dams of qinghe power plant, good agreement has been found between calculation results and real conditions

    通過上述一系列的理論分析，本文最後給出了用於評價灰壩壩體穩定的計算程序，並在清河電廠的灰壩計算中得以應用，結果顯示計算收斂快，穩定性好，結論與實際情況吻合。
  19. Furthermore, the plane dynamic graphic simulation and force analysis for lifting work course have been mainly probed in this paper. after this, it is available to select or design hoisting tools according to a special database of derrick crane and steel rope

    論文主要是對吊裝作業過程中平面動態圖形模擬和受力情況分析，引入桅桿參數和鋼絲繩參數數據庫進行吊裝機具的選擇和設計。
  20. As the structure and the dynamic characteristic of a multi - dimension force sensor influence the dynamic characteristic of a robot system deeply, therefore the sensor ' s analytic studying, the sensor ' s optimal design, the sensor ' s dynamic characteristic analysis and the sensor ' s coupling function among it ' s dimensions are also studied in this dissertation

    多維力傳感器自身的結構和特性影響機器人系統的動態特性，本論文還涉及多維力傳感器解析分析、優化設計、多維力傳感器的動力學特性分析、傳感器維間耦合函數研究等內容。本學位論文主要研究工作如下： 1
分享友人
分享到 Line

分享到臉書