end face 中文意思是什麼

end face 解釋
端面
  • end : n 1 端，尖，末端，終點。2 邊緣；極點，極限。3 結局，結果。4 目的。5 最後，死。6 【紡織；印染】經...
  • face : n 1 臉，面孔；面貌，樣子；面子，威信。2 愁容，苦臉；〈口語〉老面皮，厚臉皮。3 外觀，形勢，局面。4...
  1. Xm ) trundle needle, trundleing the post thrust bearing trundles the needle through the roll part of the body, cylinder roller and thrust maintain shelf and the thrust bed down the livestock to make up, trundleing needle and the cylinder roller is subjected to the shelf maintaining that the thrust maintains and guides. moreover thrust bed down the livestock against the difference, shaft, the pedestal encircles and employs in company, fix module shaft shoulder end face and the shell opening back plane dimensional tolerance, geometry accuracy, rigidity, axial is moved up and down, coarse degree ought to accord with the internation ， national standard stipulation demand

    滾針，滾柱推力軸承由滾動體滾針，圓柱滾子及推力保持架和推力墊圈組成，滾針和圓柱滾子受到推力保持的保持架引導，並與不同的推力墊圈，軸，座圈一起使用，安裝組件的軸肩端面和外殼孔底面的尺寸公差，幾何精度，剛性，軸向跳動，粗糙度應符合國際，國家標準規定的要求。
  2. Chuck for grinding hole and end face of bevel gear

    磨圓錐齒輪孔和端面用的卡盤
  3. The innovative dishing ring not only possesses end - face sealing capacity, but also has some radial seal and clean function

    改進的碟形密封圈不但具有端面密封能力，而且將具有一定的徑向密封和擦拭功能。
  4. The dishing ring seals belong the end face sealing parts, and act as sealing by some axial compression. because of different distribution of internal pressure and temperature, the friction inside the end - face is also different at all area

    碟形密封圈屬于端面密封元件，依靠一定的軸向壓縮量進行密封，由於端面內壓力分佈、溫度分佈不均，端面內的摩擦狀況也不是處處相同。
  5. The design of the molded lines of noiseless rocker convex - ring contact end face

    無聲搖臂凸環接觸端面型線設計
  6. ( 3 ) in the condition of invariable instantaneous speed ratio, the equations of teeth surface of all key components, such as end face gear, oscillating teeth, wave producer, et al, are deduced

    （ 3 ）在保證瞬時傳動比恆定的條件下，由空間嚙合原理出發，重點推導了活齒端面諧波齒輪傳動裝置的主要傳動部件? ?端面齒輪、活齒以及波發生器端面凸輪的齒面方程。
  7. With the face grinding attachment, perpendicularity of the end face to the bore after grinding can guaranteed

    帶有端磨裝置，保證工件端面與孔的垂直度。
  8. Ingot end face measuring system

    晶錠端面彎曲測式系統
  9. The reports of the end face harmonic gear drive of oscillating teeth are little by investigating the literature

    根據文獻檢索和申請專利時查新的結果，目前國內外還沒有進行過這種新型傳動裝置的研究。
  10. ( 4 ) the modification theory is deduced in the condition of preserving the motion state of the end face harmonic gear drive of oscillating teeth

    （ 4 ）在分析活齒端面諧波齒輪傳動裝置運動狀態的基礎上，提出了端面齒輪、活齒和波發生器端面凸輪齒面的修形方法。
  11. ( 5 ) the posterior dominating researches on end face harmonic gear drive of oscillating teeth are discussed, and some are given the preparatory method in the paper

    （ 5 ）對進一步研究活齒端面諧波齒輪傳動裝置的主要課題進行了討論和展望，並初步探討了其中部分課題的研究思路。
  12. ( 1 ) the structure and the transmission theory of end face harmonic gear drive of oscillating teeth are introduced, and the structure models which could be used are also designed in this paper

    本文主要進行了如下一些基礎性的理論研究工作： （ 1 ）提出了活齒端面諧波齒輪傳動裝置的結構和傳動原理；設計了各種可能用到的活齒端面諧波齒輪傳動裝置的結構型式。
  13. The basically theoretical researches and the design of end face harmonic gear drive of oscillating teeth are helpful. the end face harmonic gear drive of oscillating teeth will be a new member of the drives of oscillating teeth. and it has a definite application expectation and economic value

    因此，關于活齒端面諧波齒輪傳動的基礎性理論研究和開發應用，不僅增加了活齒傳動的類型，具有一定的理論意義，而且具有廣泛的應用前景和巨大的經濟價值。
  14. To enhance the reliability of bearing seal of cone bit, this paper plans to adopt face - radial combination sealing structures ; that is to say, end - face and radial seal are arranged in one bit simultaneously. the nonlinear finite element method is applied to analyze and optimize the design of sealing structures

    為了提高牙輪鉆頭軸承密封的可靠性，本文設計採用端面-徑向組合密封結構，即在一隻鉆頭中同時布置端面和徑向密封，採用非線性有限元方法對密封結構進行分析和優化。
  15. The wearing resistance, microstructure, worn surface morphology and hardness change in wearing end - face and non - wearing end - face of cr - mn - cu alloy white cast iron were tested and analyzed

    摘要對鉻錳銅合金白口鑄鐵的耐磨性、無磨損端面及磨損端面的微觀組織、磨損形貌及硬度進行了試驗和分析。
  16. 6. dual - aire swelling shaft reeling, smooth and level end face splitting

    6雙氣脹軸收卷，分切端面平整。
  17. One end face of optical fiber sample sets on the carring - table of the micr - oscope is observed, selecting appropriate amplification, afterwards, take a ph - otograph with a ccd camera, then the picture was sent to the computer by the photograph - gathering card. the image is processed with a software automatic - ally, so this method can reduce artificial errors

    具體方法是：將待測光纖製成品的一段樣品橫截面置於顯微鏡下，經顯微鏡放大，選擇合適的放大倍數，然後用ccd攝像頭攝像，利用圖像採集卡將放大后的圖像採集進計算機，利用圖像處理技術，通過軟體進行處理，從而實現處理過程的完全自動化，減少人為測量誤差。
  18. The end face harmonic gear drive of oscillating teeth contains the advantages of the common harmonic gear drive and the oscillating teeth drive, and it belongs to the three dimensional space oscillating teeth gear drive. the new kind of transmission theory introduced in this article has been applied for patent ( the application number is 200410012992. 6 ) some fundamental theory of the end face harmonic gear drive of oscillating teeth is investigated in this paper, which can benefit the design of the product and the popularization of the patent

    這種新型的傳動裝置屬于空間的活齒傳動機構，可以從根本上克服傳統的徑向諧波齒輪傳動中柔輪的變形與其承載能力之間的矛盾，並可增加同時嚙合的齒數，加大齒輪的模數，從而可以在保留徑向諧波齒輪傳動所有優點的基礎上，使其所傳遞的功率增加數十倍。
  19. End face leakage flux

    正面漏泄通量
  20. End face flux

    正面通量
分享友人
分享到 Line

分享到臉書