end groove 中文意思是什麼
end groove
解釋
終止槽-
Disigning coolant channel on the firebox of liquid rocket engine to loxodrome ( equal - angle helix ) groove can improve firebox coolant capability greatly. because the width dimension of loxodrome groove is narrow and the depth is deep, some machining methods are incapable, such as end - milling or electrochemistry. according to the peculiarities, a cnc disk - cutter - milling method which is composed of five motion axes with four simultaneously interpolated ones is researched. because most firebox generatrix is composed of complex curves, it is very difficult to get cnc cutting program with manual means. in order to deal with the problem, the loxodrome mathematics model is studied, and an auto - programming software system is developed. the software system can generate cnc cutting program of loxodrome on many kinds of turned surface. the constriction - distension segment of firebox is the most representative workpiece. the sharp changing of its generatrix slope makes loxodrome milling difficult. with the theory analyzing and practice cutting experiment, some applied techniques, which include milling mode and direction, choosing cutter diameter and cutting start point setting, are developed. adopting the technology above, tens regular workpiece have been manufacturing. the two - year manufacture practice has confirmed the validity and feasibility of developed loxodrome coolant channel milling method. the developed technology is also worth to be referenced to other similar workpiece
將液體火箭發動機燃燒室的冷卻通道設計為斜航線（等傾角螺旋線）槽形，可以大幅度改善燃燒室的冷卻性能.斜航線冷卻槽的槽寬尺寸較小而槽深尺寸較大，所以無法使用棒銑刀銑削、電化學等加工方式.針對這些特點，提出了五軸控制、四軸聯動的數控片銑刀銑削加工方法.由於燃燒室外表面的母線輪廓復雜，手工編制數控加工程序難度大.為了解決數控加工程序的編制問題，研究了斜航線的數學模型，開發了自動編程軟體系統.使用該系統，可以生成多種母線輪廓回轉體外表面上的斜航線數控加工程序.燃燒室收斂-擴張段的母線斜率變化大，加工難度大，是斜航線冷卻通道加工的最典型工件.經過理論分析和實際切削實驗，研究了針對該類型工件的片銑刀直徑選擇、銑削方式和方向、刀具調整和起刀點的設置等多項實際的加工方案.採用上述的一系列技術，已經成功地加工了數十個合格工件.經過兩年多的實際生產過程應用，驗證了所開發的斜航線冷卻通道加工方法的正確性和可行性.這些加工技術的研製成功，對其他相似類型零件的加工亦具有參考意義 -
A groove inside the end of a barrel or cask into which the head is set
桶板槽一種刻在木桶邊板兩端裝端板用的槽 -
Series of high pressure thermocouples thermalresistances and thermowells, the thermocouple take the form of spring - loaded, of which protective tube and flange are forged of special alloy, as well the thermowell are formed with bar stock drilled. more further, theconnecting between thermowell and flange can be compressed with tapered thread and the groove at the lower end of flange can be welded with argon arc. these thermocouples are usually used in high equipments of hydrogen cracking device, cracker and vaporizer etc for pressure - resistant in over 30 mpa, operating temperature from 0 up to 800
系列高壓熱電偶阻及套管，熱電偶採用彈簧壓著式，保護套管和法蘭選用特殊合金材料鍛造，套管採用棒料整體鉆孔加工而成，與法蘭連接處以錐管螺紋配合併與法蘭下端渠槽處用氬弧焊接，耐壓30mpa ，使用溫度0800 ，可長期使用在加氫裂化裝置裂解裝置，氣化爐等高壓設備中。 -
Position the two halves of the flange adapter onto the groove in the valve body end ( s ), making sure that the tab on each flange adapter half is located between the two locking lugs on the valve body ( fig. 3a )
將法蘭適配器的兩半放置在閥體連接埠的溝槽上，確保每個半邊法蘭適配器上的孔位於閥體上兩個閉鎖凸榫上（圖3a ） 。 -
The reduced pressure detector assembly shall consist of two independent torsion spring check modules, a differential pressure relief valve located between and below the two modules, two drip tight shutoff valves, and required torsion spring check modules and relief valve shall be contained within a sleeve accessible single housing constructed from 304 ( sch 40 ) stainless steel pipe with groove end connections
這種減壓檢測器總成應該包括兩個獨立扭力彈簧止回閥模塊，一個位於兩個模塊之間的下方的差壓安全閥，兩個防滴漏關閉閥，並且要求扭力彈簧止回模塊和安全閥應該放置在一個套筒內，要易於接近帶溝槽連接的304 （目錄40 ）不銹鋼管的單個外殼。 -
The basic principal and general structure of dry gas seal are introduced briefly, and aiming at the characteristics of logarithm spiral curve, the calculation of the pressure to the spiral groove end surface by the theory of narrow groove are given. the method of narrow groove theory and finite element method are utilized to optimize the end surface structure of the spiral groove dry gas seal. the structure of the seal is confirmed on the base of the result
簡要介紹了干氣密封的基本原理和一般結構，同時針對對數螺旋線形的特點，介紹了窄槽理論對螺旋槽端面的壓力分佈計算，利用窄槽理論和有限元方法對螺旋槽干氣密封端面結構進行了優化，並得出了優化結果，根據這一結果，確定了具體的密封結構。 -
Research on new virtual model of three - groove taper ball - end cutter
三溝槽錐球頭銑刀的新型虛擬模型研究
分享友人