filament temperature 中文意思是什麼

filament temperature 解釋
燈絲溫度
  • filament : n. 1. 細絲，絲狀體。2. 【紡織；印染】長絲；單纖維。3. 【植物；植物學】（雄蕊的）花絲。4. 【電學】燈絲；絲極；游絲。adj. -ed 有細絲的。
  • temperature : n. 1. 溫度，氣溫。2. 體溫。3. 〈口語〉發燒，高燒。
  1. Two kinds of wo3 powder are prepared by sol - gel method and gas - phase reaction method with tungsten filament, and heater type gas sensors to trimethylamine are made. under different work temperatures, these sensors ’ sensitivities are measured, and the result indicates that wo3 by sol - gel has better gas sensing performance to trimethylamine. at the same time, the wo3 - based gas sensor to trimethylamine can work at low temperature, which

    3 、本課題對不同摻雜的wo3材料進行了研究，發現摻雜3 % pd的wo3基氣敏元件在150ppm三甲胺氣體中，最佳工作溫度僅為85 ，該溫度下元件最高靈敏度可達11 . 7 ，並且元件的靈敏度隨tma濃度的升高而變大，這表明摻雜pd的wo3材料在低溫下對tma氣體有很好的響應。
  2. Electron gun is the foremost parts of twt, it can produce electron beam with a certain shape and current, in order to guarantee the reliability and security of work, it ’ s design have to meet to the requirement not only of electric parameter, but also all kinds of subsidiary characteristics such as filament pyrogenation efficiency, warm up time, shape size, pole space capacitance and the ability to be able to bear the press and all kinds of rigorous run conditions such as high temperature, high humidity, low air pressure, strong vibration and great strike

    由於行波管的大功率和高頻率等特性，目前還沒有任何其他的器件可以代替。行波管是應用高頻電磁場與電子注進行互作用的機理進行工作的，而電子槍是行波管中產生電子注並使它成型的基本部件，電子槍的結構設計決定了槍體自身必須具有良好的抗振可靠性，否則結構發生共振或振動位移過量，就會導致行波管的失效。因此對行波管電子槍的研究具有非常重要的意義。
  3. It has good character in roll and high temperature. second crystal temperature 1850, mainly used in white filament wire, vacuum tube heating wire

    W3102 ：繞絲及高溫性能優良，再結溫度1850 ，用於製造白熾燈絲，電子管折熱絲等
  4. This paper investigated the physical properties of polyester filament yarn such as tenacity, elongation and boiled water shrinkage by means of analyzing the poy which had been treated by different draw ratio and heating temperature

    通過對不同拉伸倍數及不同溫度處理的poy的分析，探討長絲紗的強度、伸長度及沸水收縮率等物理機械性質。
  5. Aramid filaments are treated by a low - temperature plasma with different treatment times. the surface of filaments is observed by sem and the results show that the filament surface is smooth before the treatment and becomes more rough if filaments are treated for 6 minutes. in addition, it is found that the filament peels after 9 minutes of plasma treatment

    本課題採用低溫等離子體對芳綸纖維進行表面處理后，用sem觀察纖維表面，發現未經等離子體處理的纖維表面比較光滑；等離子體處理6分鐘后，纖維表面變得粗糙，產生很多微小的刻蝕坑；等離子體處理9分鐘后，纖維表面受到的刻蝕程度明顯增加，並產生表面剝離現象。
  6. As mentioned in the introductory section, there is also an intermodulation effect caused by the minute temperature changes in the filament

    正如我們在介紹部分提到的，還存在一種由於燈絲瞬時溫度變化而導致的互調效應。
  7. Effects of physical factors on the growth of strain ag were of light intensity, temperature, inoculum volume, initial ph, effects of nutrient factors on the growth of strain ag included organic carbon sources, organic nitrogen sources, growth factors, hormone etc., and the correlation among nutrient factors being considered. the growth condition of single filament on the plate was also studied

    主要內容包括物理因子如光強、溫度、接種量和ph值等對螺旋藻生長的影響；化學因子包括有機碳源、有機氮源、生長因子、生長激素等對螺旋藻生長的影響及這些營養因子之間的綜合作用，並解決了單藻落平板生長問題。
分享友人
分享到 Line

分享到臉書