finite displacement theory 中文意思是什麼

finite displacement theory 解釋
有限位移理論
  • finite : adj. 有限的；【語法】限定的；【數學】有窮的，有盡的。n. 〈the finite〉 有限（性）； 〈集合詞〉有限物。adv. -ly ,-ness n.
  • displacement : n 1 轉位，移動；取代，置換；（人的）流離失所。2 撤換，免職。3 【機械工程】（活塞）排氣量；【航海...
  • theory : n. 1. 理論，學理，原理。2. 學說，論說 （opp. hypothesis）。3. 推測，揣度。4. 〈口語〉見解，意見。
  1. This paper focuses on the research of the stress mechanism of the ribbed shell structure in statics, dynamics and under the explosive load on the basis of the engineering practice of cave depot of single aircraft. in this paper, according to the classical shell theories, the basic differential equilibrium of the ribbed shell structure and the finite element analysis of 3d rippled plate are established, in which the function of annular ribs reinforcement bars and 3d ripped steel plates are distributed in the range of the steel, and the functions along the longitude direction of tension, bending, and torsion are neglected ; applied with dynamic analytical theory, the dynamic model of ribbed shell structure and the analytical theory model of elastic - plastic are set up ; the triangle series method is used to solve the displacement and stress under the distributed load and the concentrated load of the ribbed shell structure

    本文以軍用機場地面單機掩蔽庫工程建設為工程背景，首次對內襯三維波紋鋼板混凝土拱型復合結構的受力機理進行了靜力、動力和爆炸荷載的分析研究。根據將橫肋、鋼筋及三維波紋鋼板的作用均勻分佈在殼體范圍內的情況，忽略橫肋、鋼筋及三維波紋鋼板沿殼體母線方向的抗拉、抗彎及其抗扭作用，首次推導出了內襯三維波紋鋼板混凝土殼體的微分平衡方程，建立了有限元計算模型，並採用三角函數法，求解了三維波紋鋼板混凝土拱型復合結構在分佈荷載和集中荷載作用下的位移響應和應力響應，並與普通殼體進行了比較。
  2. Fourthly, with the finite element program, the author analyzes the relationship between the load magnitude or frequency and range of breakage or pore pressure. this can provide appropriate parameters for the method of vibrating grouting. fifthly, adopting the compressible porous medium, the author adduced dynamic theory of liquid saturated porous medium to analyze the displacement and force in the sand when there is dynamic load below the earth surface

    基於連續介質力學的混合物理論建立的多孔介質理論和動力控制方程，假設砂土滿足各向同性並處于彈性小應變狀態，豎向振動力將在飽和砂土內部產生三種波，分析了這些波的彌散曲線和特徵衰減曲線，從波傳播的角度，研究了振動力參數和土性參數對振動范圍的影響。
  3. On the basis of this velocity field and the optimization theory, the segmented displacement of the boundary of the studied area are deduced with two - dimensional finite element model of linear elasticity

    利用這個速度場，通過構建該區二維有限元模型，結合最優化原理，反演區域分段邊界位移。
  4. According to the fluctuating property of wind, on the stochastic vibration finite element theory, some calculation formulas of the response, including the along - wind response and the across - wind response, are obtained, the ideology of the torsion vibration in the double - tower structure and the ideology of the double - tower structure ' s dynamical wind load are also put forward at the same time. by using the stochastic vibration module of the general finite element program, the paper analyses the performance of the wind resistance more deeply and fully, discussing the influence on the double - tower structure from the diversification of the different component. the variance law of dynamic displacement and wind - induced vibration coefficient is derived through analyzing structure stochastic vibration, so is the effect of several parameters on dynamic displacement, acceleration and wind - induced vibration coefficient

    從結構風振的基本理論出發，通過對脈動風功率譜的分析，推導了結構風振響應（順、橫風向）的計算公式，同時提出了雙塔結構的扭轉振動和動力風荷載計算的思想，在結合通用有限元程序的隨機振動模塊的情況下，對雙塔結構的抗風性能作了深入、全面研究，探討了雙塔結構構件截面的變化對其抗風性能的影響，同時探討了順風向風速譜的選取、風速、參與計算的振型數、風與結構耦合作用是否考慮等因素對分析結果的影響，比較了規范風振系數的計算與隨機演算法結構的異同，並討論了原因，得出一些有意義的結論。
  5. This paper introduces the development and present situation of vibration absorb technology in the world ; generally analysis the rubber - bearing ( rb ) and lrb " s operative mechanism, function and the calculation of parameter ; advance the concept of standardization to lrb ; on the basis of generally analyzing the connected factor such as the site category, the diameter of lead bar, the height of bearing, the designing carrying capacity, the span of bridge, the inherent period and the displacement of rb, determine the parameter, the absorbing vibration target, the method and the process of standardization to lrb ; then according to the two - step rule of resisting and defending earthquake, and combining with the response spectrum theory in the seismic vibration of bridge, make a lot of calculation and analysis of vibration absorb design to the real bridge collected and combined by finite element program ; at last, gives the result of standardization through diagram and explains to its usage

    本論文介紹了國內外減震技術的發展和現狀；綜合分析了普通板式橡膠支座和鉛銷橡膠支座的工作機理、性能及參數的計算；提出了鉛銷橡膠支座標準化的概念；在綜合分析場地土、鉛銷直徑、支座高度、設計承載力、橋梁跨徑、固有周期以及支座變位等影響因素的基礎上，確定了鉛銷橡膠支座標準化的參數、減震目標、方法和過程；並根據抗震設防兩階段原則，結合橋梁地震振動理論的反應譜法，運用有限元程序對收集和組合的實橋進行了大量減震設計的計算和分析；最後以圖表的形式給出了鉛銷橡膠支座標準化的結果，並說明了其使用方法。
  6. In accordance with the deformation analysis of lean - caused disaster engineering and the deformation control in rectification, analysis method of the leaning reinforced concrete frame is presented using the theory of structural engineering, numerical analysis and disaster characteristics. on the basis of the analysis method, finite element is applied to analyze the stress and deformation conditions of structure in order to obtain the rectifying displacement. appling of fuzzy math to value the ultimate bearing capacity of structural element, the author puts forward the fuzzy general evaluation method of the element, and using the theory of structural engineering also gets the rectifying load

    針對傾斜病害工程的變形分析和糾傾扶正過程結構的變形控制問題，本研究論文根據建築結構理論，採用數值分析方法，並結合病害表現特徵，提出對鋼筋混凝土框架結構傾斜病害的變形分析方法；在結構的變形分析的基礎上，運用有限元方法對結構進行數值模擬，對結構的應力狀態及變形狀況作進一步的分析，確定糾傾位移量；運用模糊數學理論，提出對鋼筋混凝土病害框架結構構件的承載能力的模糊綜合評判方法，並結合建築結構理論得出最終糾傾加載量。
  7. The main contents are as follows : firstly, the structure and characteristics of aqueduct - stayed are summarized, based on which the structure analysis is presented ; planar structural models are established to simplify the analysis of internal force and displacement of aqueduct - stayed based on moment - distribution theory, the formula to calculate the force of cross section of aqueduct - stayed is derived. the finite element method for framed structures is used to analyze the aqueduct body. and corresponding computer programs are developed

    為便於計算，在計算斜拉渡槽的內力及變形時，將空間結構簡化為平面結構，分別對槽身橫斷面及槽身縱向結陶進行計算：以力矩分配法為基礎推導了槽身橫斷面內力的計算公式；運用直接剛度法，編制了桿系有限元程序進行槽身縱向結構計算，並簡單介紹與斜拉渡槽相關的剛度法知識以及程序的流程圖。
  8. Based on the theory of mechanical optimization and finite element analysis, elbow - bar mechanism of the mp1040b moulding machines made by beiren group is investigated in the dissertation. firstly, a kinematic model representing the bar mechanism is built and the nonlinear system of equations is solved through the method of gradient. meanwhile, the angular displacement, angular velocity, angular acceleration and the corresponding curves of each component in a motion period are obtained

    本文以北京人民機器廠mp1040b型模切機肘桿機構為研究對象，以機械最優化理論和有限元技術為基礎，首先對模切機肘桿機構建立數學模型，通過梯度法求解此非線性方程組，並得出機構在一個運動周期中各構件的角位移、角速度、加速度等運動參數及曲線。
  9. Firstly, the theory of compound foundation and pile foundation are summarized in this paper. the finite element, displacement models and computational program are introduced, then how such factors as the stiffness of pile, the ratio of length and radius of the pile & replacement ratio influence the settlement of compound foundation are analyzed. there has the best modulus of pile, the best of the length & replacement ratio and some data have been obtained

    首先總結了復合地基和樁基的理論和設計計算方法，對有限單元和位移模式以及有限元計算程序進行了介紹，然後分析了樁的剛度、長徑比、置換率等因素對復合地基沉降的影響，證實了帶承臺復合地基存在最佳樁土模量比、最佳長徑比和最佳置換率，並得出了相應的數值可供工程實踐參考。
  10. First, based on comprehension analysis of the present study status on optimizing method to displacement back analysis in underground engineering home and abroad, intelligent optimizing method, which fits the features of underground engineering, has been developed by introducing annealing algorithm and genetic algorithm and improving them. second, according to practical features of nonlinear displacement for underground engineering, the mechanical model on back analysis to initial ground stress and mechanical parameters of surrounding rock mass in underground engineering is established, which is based on the measuring results of displacement of convergence in underground holes. while, by introducing finite element method and combining improved annealing algorithm and improved genetic - annealing algorithm, the theory and method of elastic - plastic displacement back analysis to surrounding rock in underground engineering has been founded

    首先，本文在綜合分析國內外地下工程優化位移反分析方法研究現狀的基礎上，引進模擬退火與遺傳演算法，並對其進行改進，建立了適合於地下工程問題特點的智能優化演算法;其次，根據地下工程非線性特點，基於地下工程洞周收斂位移量測結果，建立了用於地下工程初始地應力與圍巖力學參數反演分析的力學模型，並引進有限元分析手段，結合改進模擬退火演算法與改進遺傳-模擬退火演算法，分別建立了基於這兩種智能優化演算法的地下工程圍巖彈塑性位移反分析理論與方法，並開發了相應的分析計算程序，為地下工程圍巖穩定性與開挖順序優化分析奠定了基礎;然後，在上述基礎上，根據地下工程開挖施工順序優化設計的特點，建立了基於圍巖塑性區面積的地下工程開挖施工順序優化分析模型，基於改進模擬退火演算法與改進遺傳-模擬退火演算法建立了地下工程開挖施工順序優化分析方法，並開發了相應的分析計算程序;最後，將上述分析計算程序用於工程實例分析，探討了其應用方法，證明了該文研究成果的合理性和可靠性。
  11. And the theory of the finite element method, the orthogonal test method, and the regressive interpolation are described in chapter three. in chapter four, a new 3 dof micro - displacement systems was brought out based on the analysis of the research results in the area of the multi - dof micro - displacement electro mechanical systems

    第三章對有限元計算方法、正交試驗及回歸分析方法的基本原理和試驗方法作了簡單的闡述，建立起相關的數學模型，為柔性鉸鏈的設計和微動臺的設計提供理論依據。
  12. A sensing magnetic field and displacement type of giant magneostrictive microdisplacement actuator with the functional of sensing driving magnetic field and microdisplacement is developed, and the design theories and approaches being applicable this type of microdisplacement actuator are pointed out : a circular diaphragm type of flexible construction that acts as integration mechanism of microdisplacement transferring and sensing of giant magnetostrictive microdisplacement actuator is adopted, sheet flexure theory of elasticity mechanics and approach of finite element are applied to design and calculate it, corresponding deflection and analytic formula and distribution curve of stress are given, and the specific achieving approaches of measuring principle and magnetic field sensing function of driving field in giant magnetostricitive rod are pointed out the magnetic field sensing function of the actuator is used to practically measure driving magnetic field of actuator and to obtain the relationship of driving magnetic field and coil current, which is also analyzed and studied

    其中，採用圓形膜片式柔性結構作為超磁致伸縮微位移執行器的微位移傳遞、感知一體化機構，應用彈性力學中的薄板彎曲理論、有限元方法對其進行了設計、計算，並給出了相應的撓度和應力解析式及分佈曲線；應用電磁理論給出了超磁致伸縮棒內驅動磁場的測量原理及磁場感知功能的具體實現方法，並利用執行器的磁場感知功能對其驅動磁場進行了實際測量，得出了驅動磁場與線圈電流之間的關系，並對其進行了分析和研究；對執行器內部的電磁路和偏置磁路結構進行了設計計算與實驗研究，為了減小驅動線圈的發熱，對其形狀進行了優化設計。
  13. Combining the all - function fem software and the stress analysis of suspension bridge, this paper presents a numerical method based on the finite displacement theory for model building and calculating the inner force of suspension bridges, which meets the demands of engineering construction

    本文以有限位移理論為基礎，將現今通用有限元分析軟體與懸索橋內力分析結合，探尋一套懸索橋有限元建模、計算的數值方法，以滿足工程建設要求。
  14. The thesis analyze a on - the - spot test model combining a projiect. utilizing the non - linear finite element theory in the article, form - finding has been took apart with node balanced laws and propping up move law. under the loads every calbe unit strength of axle and node displacement ' s variation tendencies are computed

    論文還結合工程實踐對一現場試驗模型進行了分析。文中利用非線性有限元理論，按節點平衡法與支座移動法進行找形分析。計算了外荷載作用下各索單元軸力及節點位移的變化趨勢。
  15. In order to restrict the displacement of relaxed rock effectively, the factors affecting the efficacy of anchor measures are analyzed according to mechanism of action of anchor. in terms of principle orthogonal design, the influence of parameters of anchor to displacement of excavation slope are elevated by computing using finite element method simulation, and the optimal scheme of anchoring parameters including length of anchors and space between bolts and thickness of shot concrete are defined. finally, the optimal scheme of anchor parameters are determined with considering results of theory analyse and numerical calculation, which provide theory bases for engineering

    為了有效防治邊坡開挖后巖體的鬆弛變形，根據錨桿的作用機理對影響錨固效果的主要因素進行分析，並利用處理多因素試驗的科學方法?正交設計原理，以有限元數值計算為手段，以有效約束邊坡開挖位移為標準，評價了錨桿長度、錨桿間距、混凝土噴層厚度等錨固參數對邊坡變形的影響大小和規律，經過比較分析最終提出了錨固參數的優化設計方案，為工程設計提供了理論指導。
  16. First of all, using the timoshenko beam theory and the finite element method, according to lagrange equation, the dynamic models of flexible - link manipulators and those with joint and link flexibility are proposed base on actual displacement

    首先，基於實際位移，採用timoshenko梁理論和有限元法，由lagrange方程建立了柔性臂機器人和考慮關節柔性和臂柔性的機器人動力學模型。
  17. Through the detailed analysis of cavity expansion theory, strain path method and finite element theory applied in jacked pile, some deficiencies are put forward. according to the analysis, some main original work are made. firstly, on the basis of strain path method ( spm ), closed - form analytical expressions of displacement fields caused by the installation of jacked pile are obtained in small strains

    本文首先詳盡地分析了圓孔擴張理論、應變路徑理論、有限元理論在靜壓樁擠土效應方面存在的不足，並在此基礎上做了如下工作： 1 、基於spm法的理論基礎，在小應變假定情況下，推導了靜壓單樁周圍土體位移場的解析解。
  18. In order to fully develop the theory of squeezed branch piles, in particular, the justification of its superior performance in terms of the bearing capacity and sinking displacement, we have derived the analytical formulas of the axial load and the strain at arbitrary depth ; based on existing static loading test results and research on belled pile, together with the analysis of on - site testing data, we have applied the expand theory on sphere holes to the computation of radial stress of squeezed branch piles under hole expansion ; taking the oil pressure of hole expansion in to account, we have find the a branch force under certain hole pressures, hence we can estimate the maximum bearing capacity of single piles ; we have introduced the experiential formulas for the bearing capacity of squeezed branch piles based on its stress characteristic and pile testing data ; we have also done numerical simulations of squeezed branch piles utilizing finite element method software ansys ; we have matched the simulation res ults with those of on - site basic load experiments, regenerating the distributions of stress fields and strain fields of squeezed branch piles, and from those distributions, we can determine the optimal distances between plates and piles

    為了完善支盤樁的設計理論，探求支盤樁高承載力和低沉降量的內涵，本文推導出了支盤樁任意深度的截面荷載以及位移隨深度變化的理論公式；基於已有的靜載試驗成果及有關擴底樁的研究成果，從對現場測試數據的分析，將球形孔擴張理論引入到支盤樁擴孔時徑向應力的計算，考慮到擴孔時的油壓數據，求得某一孔壓下的支盤力，據此估算單樁極限承載力；同時根據對支盤樁的受力特點和試樁數據的分析，提出了支盤樁承載力計算的經驗公式；用有限元分析的方法，利用大型有限元分析軟體ansys對支盤樁進行數值模擬，並將模擬結果同現場的靜載試驗結果進行對比，再現了支盤樁在荷載作用下土中應力場和位移場的變化，根據應力場和位移場的變化范圍，指出最佳盤間距和樁間距；為支盤樁的設計和施工提供了一個可量化的設計依據。
分享友人
分享到 Line

分享到臉書