friction error 中文意思是什麼

friction error 解釋
摩擦誤差
  • friction : n. 1. 摩擦，阻力。2. 傾軋，沖突，不和 （between）。3. 擦熱皮膚。
  • error : n. 1. 錯誤；失錯。2. 謬見，誤想；誤信；誤解。3. 罪過。4. 【數學】誤差；【法律】誤審，違法；（棒球中的）錯打。adj. -less 無錯誤的，正確的。
  1. It is apparent that the error of piecing and locating the corrugated pipe and the error of level and upright and leaking in the part lead to increase of friction loss

    究其原因，與施工工藝密切相關，主要是波紋管逐節段拼接定位、平直度誤差及局部漏漿等所致。
  2. The experiment research on friction moment dynamic error of rolling bearing

    滾動軸承摩擦力矩動態誤差的實驗研究
  3. The experiment and simulation results show that the stabilization error peak is caused by the step friction torque when the disturbance changes its direction

    實驗和模擬顯示轉臺穩定誤差在擾動換向時的「尖峰」由轉臺轉軸的靜摩擦階躍干擾力矩產生。
  4. The step friction torque is the main source for the stabilization error

    這種干擾力矩是對穩定誤差影響最大的因素。
  5. Simulation system of a single axis stabilized turntable system shows that the peak of the stabilization error is caused by the step friction disturbance torque

    針對一個單軸穩定轉臺進行的模擬和實驗結果表明，在擾動換向時產生的穩定誤差尖峰由擾動換向時的階躍摩擦乾擾力矩產生。
  6. There are different nonlinear factors in the double - axis control system, such as friction 、 saturation. these nonlinear factors result in control error, such as track error

    伺服系統中存在著各種非線性因素，如摩擦力、飽和等，這些非線性因素導致控制的誤差，如跟蹤誤差，影響控制的性能。
  7. Emphasis is placed on analyzing the influences of friction characteristics on hydraulic motor, dynamic coupling between gimbals, resolution ratio error and setting error of feedback measurement element on accuracy of electro - hydraulic position servo system for a certain simulation turntable

    摘要針對具體的模擬轉臺電液位置伺服系統，著重分析了液壓馬達摩擦非線性、框架間動力學耦合、反饋測量元件的解析度誤差和安裝誤差對轉臺電液位置伺服系統精度的影響。
  8. From the experiment and analysis, it can be seen that friction limits realization of high accuracy electro - hydraulic position servo system, movement of any gimbal brings disturbance moment to servo system of other gimbals and the disturbance moment causes error, and, resolution ratio error and setting error of feedback measurement element are directly added to servo system output

    通過實驗和模擬可以看出，摩擦阻礙了轉臺電液位置伺服系統商精度控制的實現，任何一個框架的運動都會對其餘框架的伺服驅動系統產生干擾力矩並引起伺服系統誤差，反饋測量元件的解析度誤差和安裝誤差直接反映在伺服系統輸出上，對伺服系統的精度有直接影響。
  9. The sine is used in the simulation. being aimed at the compensation methods of both the adaptive control basing on the friction model and the repeat control regulator, some experiments are carred out to verify the effectiveness and feasibility of the compensation. the signals which are introduced into the system are ramp and sine for testing the minimum stable speed and error

    針對第三章中提到的基於摩擦模型的自適應低速補償方法，以及第四章提出的不基於模型的重復迭代學習控制的低速補償方法，在系統中分別引入了斜坡信號和正弦信號進行了實驗測試，並與pid控制結果進行了比較。
  10. This paper applies the theory of metallic material acoustics and internal friction, the base of vibration dynamics and metallic dynamics to analyze the testing data. the result indicates the relative error is below 0. 5 %. the demands of the design are satisfied

    本文利用金屬材料聲學內耗理論、振動力學基礎、金屬動力學理論對實體測試結果進行綜合分析，結果表明測量的相對誤差小於0 . 5 ，達到了設計要求。
分享友人
分享到 Line

分享到臉書