injection advance 中文意思是什麼

injection advance 解釋
噴射提前
  • injection : n. 1. 注射。2. 注射劑，注射液，針藥，灌腸（藥）。3. 充滿，注滿。4. 【醫學】充血。5. 【機械工程】噴射。6. 【宇宙空間技術】（衛星等的）入軌，射入軌道，射入軌道的時間[地點]。
  • advance : vt 1 進，推進；促進（生長），助長；撥進（時針），增進；提早，提前。2 使升級，提升。3 提高，抬高，...
  1. Advanced gas engine test - bed is tested repeatedly to collect and analyze the data parameter of the injection advance, pressure compare and outside characteristics of the supercharging and mid cooling diesel - engines

    採用先進的內燃機試驗臺架反復測試，對增壓中冷柴油機的供油提前角、增壓壓比、外特性等各項性能參數進行數據採集，並對所採集的數據進行相關分析。
  2. The best compression ratio and fuel injection advance angle are calculated through mess optimization calculation program of language c. on the basis, optimization simulation of inlet and exhaust timing has been carried with the diesel engine working model to increase diesel engine ' s volumetric efficient

    在此基礎上，利用柴油機工作過程模型，對進排氣正時進行了優化計算，以提高柴油機的充氣效率，改善燃燒性能，為進一步改善該機性能指明了方向。
  3. A new calculation method for optimizing diesel engine performance, called nonlinear regression - mess method, is put forward. in this paper, 25 groups of simulated values are calculated from the diesel engine working model, specific fuel consumption, peak pressure, rate of pressure rise, nox and peak temperature are fitted into explicit function about compression ratio and fuel injection advance angle

    本文利用柴油機工作過程模型，得出25組模擬計算數據，利用非線性回歸將油耗、最大爆發壓力、壓力升高率、 no _ x濃度及最高燃燒溫度擬合成壓縮比和噴油提前角的顯函數，並用網格法進行優化，用c語言編制了優化計算程序，得出最佳的壓縮比和噴油提前角，使其優化匹配。
  4. So it is proved that the working model is right, and on the basis, the influences of the compression ratio and fuel injection advance angle on the diesel engine ' s combustion performance are studied. ( 2 ) energy resource and environment protection are two important problems that diesel engine is faced with. so in this paper the constrained optimization is studied in order to decrease fuel consumption within the limitation of the regulation on exhaust emission and power output

    （ 2 ）能源和環境保護是柴油機存在和發展的兩大問題，因此本文在滿足排放法規及柴油機動力性的基礎上，以降低油耗為主要研究目標，進行有約束條件的優化計算，並提出了一種新的柴油機工作過程優化計算方法? ?非線性回歸?網格法。
  5. The performance experiments of emulsified diesel oil are done on a 1135 diesel engine. by a lot of experiment data and charts, the factors that influence the combustion effect are analyzed, including the factors of emulsified fuel self such as emulsifiers, water content, emulsifying way, and the factors of diesel engine such as fuel injection advance angel, injection pressure, load, model of engine, and so on

    在1135柴油機上進行了乳化柴油的臺架試驗，通過大量試驗數據及圖表分析了影響乳化油燃燒效果的因素，包括乳化油自身的因素如乳化劑、含水量、乳化方法等，以及發動機的狀況與參數如噴油提前角、噴油壓力、工況、機型等。
  6. 5. no parts and components warranty will be delivered if customer or non - warranty - taker dismantles disassemble and adjusts parts, assembly of the diesel and components that are not allowed to be adjusted such as injection pump assembly lead sealing, and reassembles them within the warranty term, which however, fails to meet technology demand such as torque and advance angle of major bolts, resulting in failure and damage of relevant components, assembly and parts

    在保修期內，顧客或非承擔保修者拆卸解體調整柴油機的部件總成和規定不得調整的部位如噴油泵總成鉛封等，重裝后又未達到技術要求如重要螺釘的扭矩噴油提前角等，導致部件總成和相關聯零部件失效和損壞，由此涉及的零部件
  7. Injection time switchover temperature affects the viscosity of the melt, which presents resistance to the advance of the screw

    注射時間轉換溫度影響熔融塑料的粘度，而粘度會給螺桿的頂部帶來阻力（反壓力） 。
  8. The paper researches the motorcycle ' s administrative system microems, which provide the experimental support of the injection and the ignition advance angel. it is very difficult to measure quite high exact value of atmospheric pressure. this paper introduces a new mathematic model that aims to obtain the intake pressure and the injection fuel of the engine cycle

    本文對摩托車汽油機管理系統microems的組成與功能進行了研究，為電控摩托車發動機噴油及點火控制建模與模擬提供了實驗硬體支持，同時也為主要參數進行測量和數學建模提供理論依據。
  9. Aiming at high design requirement and great technical difficulties, construction methods such as blasting control, excavating and mucking in the tunnel and grout injection in the holes with anchor have been improved on so as to advance construction efficiency, quicken construction schedule and increase economical benefits finally

    針對此工程設計要求高、技術難度大等特點，對爆破控制、洞室開挖出渣、錨桿注漿等施工方法進行了改進，提高了施工工效，加快了施工進度，最終提高了經濟效益。
  10. It ' s the first time to question extensively the influences of fuel delivery advance angle and injection pressure on performance of e30 engine

    首次系統地研究了供油提前角、噴嘴啟噴壓力對e30混合燃料發動機性能的影響。
分享友人
分享到 Line

分享到臉書