installation diameter 中文意思是什麼

installation diameter 解釋
裝配圖
  • installation : n. 1. 就職，就任，就職禮。2. 裝置，設備。3. 安裝；設置；安置。4. 軍事設施。
  • diameter : n. 1. 直徑。2. （顯微鏡等的）放大倍數。
  1. While installation the ambient temperature should not be lower than 0, and the bending radius radius should not be less than 10 times of outer diameter of cable

    敷設電纜時的環境溫度不低於0 ，最小彎曲半徑應不小於電纜外徑的10倍。
  2. The generously designed drill rod clamping device can be opened up fully to enable the installation of drilling tools and drill casings exceeding 171 / 2 " ( 444 mm ) in diameter

    如圖所示的鉆桿夾持裝置可安裝最大直徑為444毫米的鉆具和套管
  3. Aimed at the equal - diameter cam mechanism with follower of planar movement, and according to two conditions of existing meaningful solution of the mechanism and of ensuring transmission angle of output swinging rod, the value selection ranges of cam motion angle, of swinging angle of out - put swinging rod and of its primary installation angle were analyzed and determined, and then proceed to plot the region graph of selectable value for motion angle of cam and swinging angle of swinging rod, thus provided convenience for the design and employment of that mechanism

    摘要針對平面運動從動件等徑凸輪機構，根據機構存在有意義解和保證輸出擺桿傳動角兩個條件，分析並確定了凸輪運動角、輸出擺桿擺角及其初始安裝角的取值范圍，進而繪制了凸輪運動角與擺桿擺角的可選值域圖，為該機構的設計與使用提供了方便。
  4. There are basically three components in experimental installation of a high voltage supplier, a capillary tube with a pipette or needle of small diameter and a metal collecting screen

    電紡絲技術的基本裝置由高壓直流電源、帶有細小噴絲頭的樣品管和收集板三部分組成。
  5. The length should be added if the cost is n ' t increased and the installation is convenient, the diameter should be chose by the local weather condition and the using requirement ; the gas pressure should be not higher than 5 x 10 - 2pa and the emissivity should be less than 0. 1, the spring should be small and narrow in order to decrease the heat loss, the gas absorbed getter should not be too many as long as it can absorb the residual gas and keep the vacuum degree

    在不影響安裝和增加成本的情況下，應適當增加太陽能真空集熱管的長度;根據當地的氣候條件和使用要求來綜合考慮選擇直徑;國標規定的真空度必須達到5x10 』 zpa ，發射率小於0 . 1是合理的;彈簧卡子不要選用很寬、很大的尺寸，盡量減少接觸熱損;吸氣劑並非越多越好，只要能夠吸收殘余氣體，保證一定的真空度即可。
  6. Fit for observation. decision of gauge diameter ( shape dimension ) should be based on installation site and illumination condition

    適于工作人員的觀測。根據檢測儀表所處位置和照明情況選用表徑（外形尺寸）不等的儀表。
  7. Installation temperature should be not lower than 0, and recommended allowable bending radius should be not less than 12 times of overall diameter of cable

    2電纜的敷設溫度應不低於0 ，推薦的允許彎曲關徑不小於電纜外徑的12倍。
  8. The needie roller bearings are compact in radial structure. when their inside diameter and loading capacity are identical with that of other kinds of bearings, the outside diam - eter of tfem is smallest. so they are acceptable especially for the supprting structures which radial installation dimension is the first value. the bearings can sustain the radial loads only

    滾針軸承徑向結構緊湊，其內徑尺寸和負荷能力與其它類型軸承相同時，外徑最小，特別適用於徑向安裝尺寸，首先值的支承結構，只能承受徑向負荷。
  9. Power transformers ; fans, blade diameter 350 mm, for open - air installation

    電力變壓器.戶外裝置用葉片直徑350mm風扇
  10. During installation the min ambient temperature shall be above 0 and the bending radius of cable shall not less than 6 times of its external diameter

    電纜的敷設溫度不低於0 ，推薦的允許彎曲半徑為不小於電纜外徑的6倍。
分享友人
分享到 Line

分享到臉書