jacket temperature 中文意思是什麼

jacket temperature 解釋
（發動機汽缸）水套內冷卻水溫度
  • jacket : n 1 短上衣，外套。2 包書紙，護封；公文套；唱片套；彈殼。3 （動物的）皮毛；（馬鈴薯等的）皮。4 【...
  • temperature : n. 1. 溫度，氣溫。2. 體溫。3. 〈口語〉發燒，高燒。
  1. Throughout september short - sleeved shirts and sandals may be worn. but from october onward, when the temperature starts falling in the morning and evening, a jacket will be necessary

    9月雖然可以身穿短袖襯衫、腳穿拖鞋，但早晚氣溫開始下降， 10月以後就必須穿外衣了。
  2. Specific dead - end design and performance depends upon a number of factors such as cable brand and design, strength member construction, jacket type, tension load requirements, temperature and environmental operating conditions, and so on

    使adss光纜的表面及芯部光纖免受損傷。充分考慮有效地保護adss光纜，該類線夾採用內外層預絞絲結構。
  3. Concentric jacket pipe surrounded the test condenser. steam was generated in the boiler, flowed upward to the inlet of connection pipes, then flowed downward into the condenser tube, the cooling water flowed countercurrently through the annulus. the experiment covered the range of the pressure 1. 0 ~ 3. 0bar, heating power 2. 0 ~ 15. 0kw, steam mass flow rate 0. 001 ~ 0. 004kg / s, air mass flow rate 0. 0 ~ 0. 00163kg / s, and cooling water temperature 20 - 60 ?

    在系統壓力為0 . 1 0 . 3mpa ，加熱功率為2 15kw ，蒸汽質量流量為0 . 001 0 . 004kg s ，空氣質量流量為0 . 0 0 . 00163kg s ，二次側冷卻水溫度20 60的范圍內，系統研究了豎直下降管內含有空氣的蒸汽冷凝特性，獲得了不同壓力、不同空氣含量和不同加熱功率下，冷凝段的溫度分佈和局部熱流密度的數據。
  4. Don t forget to bring along a jacket with you as the temperature will fall at night

    晚上天氣會轉涼，可不要忘了多帶一件罩衫或外套。
  5. In chapter 5, thermal characteristics of spindle system with cooling jacket are analyzed on xk717 cnc milling machine by combining 3d finite element model with the temperature model of cooling water between spindle system and water tank. the effect factors to thermal behavior of the main spindle system are studied by analyzing both cooling parameters and structure. finally, the main conclusions and prospects for the future research are presented

    第五章建立了xk717數控銑床主軸及主軸箱的三維有限元模型，結合普通水箱進行冷卻時冷卻水溫升的數學模型，對帶有冷卻套冷卻的銑床主軸系統進行熱特性分析，得出了各種參數（如冷卻泵的流量、水箱的大小、散熱狀況及冷卻水的溫度）對主軸熱特性的影響規律;並提出了對主軸冷卻套的布局進行改進的想法，從而為數控銑床的設計提供了理論依據。
  6. Characteristic : water - jacket heating mode. temperature is even in the working chamber. if power failure, the chamber can keep constant temperature for longer

    特點:隔水式加熱方式，溫度均勻且斷電后仍能保持較長時間恆溫
  7. It adopts stainless steel working chamber and water - jacket heating mode. temperature is even in the working chamber. if power failure, the chamber can keep constant temperature for longer

    不銹鋼工作室，隔水式加溫方式，溫度均勻且斷點后仍能保持較長時間恆溫。
  8. The heated part of thermal resistance temperature sensor is thin wire which circled framework that made up by insulated material. if there is different temperature in the measured medium, the measured temperature is its average temperature. although the shapes of thermal resistance are different, their basic structure are same on the whole, usually composed by temperature sensor insulated jacket protective tube junction box, etc

    熱電阻的受熱部分感溫元件是用細金屬絲均勻地雙繞在絕緣材料製成的骨架上，當被測介質中有溫度梯度存在時，所測得的溫度是感溫元件所在范圍內介質層中的平均溫度。
分享友人
分享到 Line

分享到臉書