kinematic method 中文意思是什麼

kinematic method 解釋
運動學方法
  • kinematic : adj. 【物理學】運動學（上）的。adv. -ically
  • method : n 1 方法，方式；順序。2 （思想、言談上的）條理，規律，秩序。3 【生物學】分類法。4 〈M 〉【戲劇】...
  1. Test method for kinematic viscosity of asphalts bitumens

    石油瀝青運動粘度測定法
  2. The paper advances a creative design method of mechanism structure based on single - gemel kinematic chain. by replacement pairs of single - joint kinematic chains and symbolization usual kinematic pairs, author

    本文在總結前人提出的多種結構創新綜合方法的基礎上，提出一種基於單鉸運動鏈的機構結構創新設計方法。
  3. Compared with the static method and kinematic method computing deformation directly, the method presented here bring high efficiency when calculating the influence surface of the internal force for curved - bar grillage

    與靜力法及直接求解位移的機動法相比，使曲桿梁格內力影響面計算效率得到了很大提高。
  4. During simulation of kinematic calibration of virtual axis machine tool, indirect method is used for measuring its position and orientation ; meanwhile jacobean matrix regrouping method is used instead of arduous optimization to avoid measurement noise maginification

    摘要在對虛擬軸機床進行運動學標定的模擬計算過程中，採用間接測量法對虛擬軸機床的運動進行間接測量，然後通過矩陣重構的方法來解決測量噪聲的干擾問題。
  5. This paper presents an assur - group method for the kinematic analysis of plannar cam mechanisms. during inversion, each instantaneous cam mechanism is transformed into an assur - group in this method

    該方法是把反轉中的凸輪機構的各個瞬時機構轉化為桿組，通過對桿組的分析完成對凸輪機構從動件的運動分析。
  6. Some examples are given in this dissertation. first, the coordinate values of a group of discrete points on the cam profile are achieved by conventional design method which are then used as measured data of the cam profile. then the kinematic analysis of the cam mechanism is performed by the method developed in this paper

    本文以已知從動件運動規律的凸輪機構為例，利用正設計方法求出凸輪實際廓線一組離散點坐標值，並以此作為凸輪檢測數據，運用本文提出的分析方法進行運動反求，並將反求所得結果與理論結果加以分析比較。
  7. On the basis of appraising a traditional method, the method of the stereographic projection and proportionally stereographic projection of a solid volume, this paper has introduced such methods as determination of dominant discontinuities, kinematic tests for rock - mass failure modes, geometrical judgment of a removable block, and determination of a key block, extending perfecting the traditional method, and thus making it has better suitability or availability and practicality

    摘要本文在評價用傳統方法即赤平極射投影和實體比例投影方法分析節理邊坡穩定性的基礎上，結合具體工程實例引進了優勢結構面的確定、巖體破壞模式的運動學判釋、可移動塊體的幾何判定和關鍵塊體的確定等方法，使傳統方法得到拓寬和完善，從而具有更好的適用性和可操作性。
  8. Turning variables iterative method for kinematic analysis of complex planar link ages

    復雜平面機構運動分析的角變量逼近法
  9. Abstract : in this paper, the distinct element method is adopted to study the force and the motion of granular burden from a kinematic view point. the numerical model of bell - less top charging is established. the charging process and burden surface profile have been imitated

    文摘:從動力學角度，採用離散單元法研究爐料顆粒的受力和運動，建立高爐無鐘爐頂布料數值計算模型，模擬無鐘爐頂布料過程和料面形狀。
  10. The result indicates that this method is feasible. the first derivative of kinematic parameters can been calculated well while the second ones can ’ t which need filter

    其中一階運動學參數求解效果較好，而二階運動學參數並不是很理想，摻雜進了高頻噪聲，需要進行濾波處理。
  11. The acceptability our rejection and the depiction of some content in the course " mechanisms and machine theory " is discussed, ( e. g., group dividing, solving steps of the graphical method for vector equation, versions and methods for analytical kinematic analysis, inversion design for linkage mechanisms, crank angle between the two limiting positions, design formulae for cam mechanisms, classification of combined mechanisms, formula of the radius of addendum circle of gear, balancing of machinery, etc. ) and some new opinions are presented

    摘要就《機械原理》課程的某些內容（如：拆桿組的方法、矢量方程圖解法的解題步驟、運動分析解析法的版本和方法、連桿機構的反轉法設計、極位夾角、凸輪機構設計公式、組合機構的分類、齒輪齒頂圓半徑公式、機械的平衡等）的取捨和敘述進行探討，提出一些新的看法。
  12. To solve the poor precision problems of dataglove angle outputs, this paper builds human hand kinematic model and fingertip position error model, and gets the precise parameters of human hand model by the parameters identification based on fingertip positions closed loop method

    本文針對數據手套關節角度輸出精度低等缺點，建立了人手的運動學模型和各指尖位置的誤差模型。基於指尖位置閉環的方法完成了人手模型的參數識別，提高了人手模型幾何參數的精度，得到了較精確的人手手指指尖位置。
  13. Firstly, in respect of the cycling equipment, i use the method of analyzing lever to build the kinematic and dynamic model of cycling

    首先，結合fes腳踏車系統機械運動裝置的特點，用桿件運動分析方法，建立了蹬踏運動的運動學和動力學模型。
  14. So we can complete the kinematic analysis of the cam mechanism by the analysis of the corresponding assur - group. based on the method, this paper deals with plannar disc - cam mechanisms with different types of followers. the main points of this paper are as follows

    基於桿組的分析方法，本文圍繞各種類型從動件的平面盤形凸輪機構做了如下工作： 1 .根據凸輪機構的檢測數據利用三次周期樣條函數插值法對凸輪實際廓線進行曲線擬合。
  15. The kinematic algorithm of the basic unit is given based on the position analysis method of single - loop spatial linkages and he kinematic influence coefficient method. a computer program for automatic analysis of spatial mechanisms is developed

    結合單環空間機構的位置分析方法及速度、加速度分析的影響系數法，給出了剛轉化單元的運動分析方法:最後編製程序，實現了多月生} ， bj機構運動分扔的自動化。
  16. Method of inverse displacement analysis for hybrid twe pmts is a1so given. an analytical method, which is based on surface analysis, for workspace - analysis of 6 - sps type pmts is proposed in this dissertation. topological diagram of workspace for 6 - sps type pmts is derived, the equations of workspace boundny surfaces for 6 - sps type pmts are also derived based on the kinematic characteristic of the pmts

    提出了一種求解6 - sps型並聯機床主進給機構工作空間的解析方法，該方法以曲面分析為基礎，通過分析得到了6 - sps型並聯機床主進給機構工作空間四川大學博士學位論文的拓撲邏輯結構圖，結合主進給機構的運動特性，得到了主進給機構工作空間邊界曲面的曲面方程。
  17. The kinematic synthesis equations for rrr and rpr groups have been established, respectively, based on the single - opened - chain ( soc ) theory and displacement matrix method. combining two kinematic synthesis equations for rrr groups, this paper presents the unified kinematic synthesis equations for hinged 3 - bar groups which are applied in function synthesis of planar watt, stephenson, and 6 - bar linkages

    基於單開鏈理論，應用位移矩陣法，分別建立了rrr和rpr兩種級桿組的運動綜合方程，再將兩個rrr級桿組的綜合方程聯立，得到watt型及stephenson ，型六桿函數發生機構中鉸鏈三桿組的統一運動綜合方程組。
  18. A rule - based generating method was put forward to improve the efficiency of mechanical kinematic function scheme design

    摘要為提高機械產品運動功能方案設計效率，提出基於規則的功能方案生成方法。
  19. This paper analysed the kinematic principle of gear four - bar linkage combining mechanism, and deduced the formula of calculation presented the method of optimization design

    分析了齒輪四桿組合機構的運動原理，推導出了計算公式，並給出了該組合機構尺度綜合的優化設計方法。
  20. 2. based on the muller - breslau principle, formulars of equivalent nodal loads for the curved - and straight - beam element while occuring unit relative constrained displacement have been deduced. the influence surface of the internal force for grillage has been analyzed by combining kinematic method with finite element static method, using the superposition principle applied to little deformation

    根據米勒-布雷斯勞原理，推導了曲梁、直梁截面發生單位強迫相對位移時的等效結點荷載計算公式，運用小變形的疊加原理，將梁格機動分析與梁格有限元靜力分析相結合建立了內力影響面。
分享友人
分享到 Line

分享到臉書