main suction 中文意思是什麼
main suction
解釋
絕熱式角閥-
Reconnect main lumen to suction source.
請將主腔管道連接吸引源。 -
Under special conditions such as low partial load / deep vacuum, unexpected high air leakage resulting in a major temperature difference ( above 10 c ) between the steam exhaust turbine temperature and all air - take off temperature measurement, the suction capacity can be improved by using 2 main ejector simultaneously
在特殊條件如局部低載荷/極端真空，不正常的熱交換，意想不到的高空氣泄漏導致的在蒸汽排氣溫度和抽空溫度測量上產生的嚴重溫差（ 10 c以上） ，用兩臺主抽汽器同時工作可以提高抽氣量。 -
The tension force, shear forces ( including pushing force, cutting force and friction force ), impulse force, hydrodynamic drag on the suction pipes, and the force resulted from the pressure difference, etc, are the main forces for detail discussion in this paper
詳細討論了主要作用力：在波浪補償器作用下的纜繩拉力、耙頭與海床間的土壤剪切力、作用在耙吸管上的水流阻力及由於壓力差在耙頭處產生的推動力等。 -
Main products of this company are : single - use vein needle, anaesthetic puncture bag, infusion pump, puncture bag for thorax, canula for trachea, trachea cut cannula, sputum aspirator pipe, suction connection pipe, urethral catheterization bag, general anesthesia bag, dressing change bag, oxygen therapy pipe, etc
公司主要產品有:一次性使用靜脈留置針，麻醉穿刺包，輸注泵，胸腔穿刺包，氣管導管，氣管切開插管，吸痰管，吸引管、連接管，導尿包，全麻包，換藥盒，輸氧管等 -
The main work embodied as follows. ( 1 ) model a biowhig / suction type boundary for synthetic jet actuator, it considers the actuator cavity, exit nozzle and exterior flow field as a single computational region
（ 2 ）本文的主要工作之一是基於建立的激勵器簡化模型對合成射流流場進行二維、三維數值分析以探討合成射流流動機理。 -
Plate valves for displacement compressors ; suction valves, discharge valves ; main dimensions, materials, installation
容積式壓縮機的板閥.吸氣閥.放氣閥.主要尺寸.材料和 -
As an inlet structure, the forbay is an important part of the pumping station. the pressurized forbay, close in top structure, is a kind of particular forbay in which water is pressurized. based on the integral hydraulic model test of shanghai changqiao waterwork ' s water - transport pumping station, some research on the hydraulic characteristics of the pressurized forbay has been done in the paper. the main content is listed as follows : l. the hydraulic characteristics of the pressurized forbay in different water supply combination and different pump unit combination without divertion measure, and the reason of the poor flow state. 2. the hydraulic characteristics of the pressurized forbay with diversion pier, and the reason why the flow state can be improved. 3. the experimental research on the critical air suction condition of the pressurized forbay
本文基於上海長橋自來水廠改造工程送水泵站整體水力模型試驗，對有壓前池的水力特性進行了研究，研究的主要內容如下： 1 、無導流措施的有壓前池在不同供水組合及不同機組開機組合條件下的水力特性，並分析了流態較差的原因； 2 、加設導流墩後有壓前池的水力特性，以及加設導流墩流態改善的原因; 3 、有壓前池進氣臨界條件的試驗研究； 4 、水泵進氣以後水泵性能的討論。 -
End - suction centrifugal pumps, rating with 10 bar with bearing bracket - nominal duty point, main dimensions, designation system
帶支承架的額定值為10bar的端吸式離心泵.公稱負荷點主要尺寸和命名系統 -
End - suction centrifugal pumps, rating with 10 bar with bearing bracket. nominal duty point, main dimensions, designation system
帶支承架的額定值10巴的端部吸入式離心泵.公稱負荷點主要尺寸和命名體系 -
End - suction centrifugal pumps, rating 10 bar with bearing bracket - nominal duty point, main dimensions, designation system ; german version en 733 : 1995
帶軸承座和pn10軸向埠的離心泵.額定功率.主要尺寸 -
Wastewater treatment plants - rectangular tanks - part 3 : grit chambers with suction type sludge remover and sludge scraper ; types, main dimensions, equipment
廢水處理廠.矩形儲罐.第3部分:吸入式污泥清除器和污 -
Several problems in chamber design of main suction drainage system
吸入式主排水系統硐室設計中的幾個問題 -
Wastewater treatment plants - circular tanks - settlement tanks with sludge scraper, suction type sludge remover and thickener ; types, main dimensions, equipment
廢水處理廠.圓形儲罐.帶污泥鏟運機吸入式污泥清除 -
Wastewater treatment plants - rectangular tanks - part 1 : settlement tanks with sludge scraper, suction type sludge remover and chain scraper ; types, main dimensions, equipments
廢水處理廠.矩形儲罐.第1部分:帶污泥鏟運機吸入式
分享友人