melt quality 中文意思是什麼
melt quality
解釋
熔體質量-
Abstract : to increase industrial grade silicon product quality, bottom blowing melt of industrial grade silicon outside the furnace can effectively decrease al and ca contents in industrial grade silicon
文摘:為提高工業硅產品質量，採用爐外底吹氧化精煉工業硅熔體，有效地降低了工業硅中鋁、鈣雜質的含量。 -
With theoretical analysis and production practice, the omens of cupola melt oxidation, the mechanism and reasons of iron melt oxidation, its influence on castings quality were described, and measures to prevent melt oxidation were proposed
摘要通過理論分析和生產實踐，敘述沖天爐鐵液氧化的特徵、鐵液氧化的發生機理和原因、鐵液氧化對鑄件質量的影響，以及在生產中預防鐵液氧化的措施。 -
Several flux systems have been studied, especially about the mixed flux system. we found that the use of mixed systems such as k2co3 - b2o3 - naf had greatly decreased the viscosity of the melt, decreased the saturation point and improved the growth quality of the crystal. the flux system naf - b2o3 is favour of decreasing the volatilization and the saturation point of the melt
對kabo晶體的幾種助溶劑體系尤其對復合助溶劑體系進行了研究，我們發現復合助溶劑體系如： k _ 2co _ 3 - b _ 2o _ 3 - naf有利於減小熔體粘度，降低飽和點溫度，改善晶體的生長性能； naf - b _ 2o _ 3體系有利於降低熔體揮發性和飽和點溫度。 -
In this paper closed - cell foam samples with basically controllable pore structure and uniform distributed pore were prepared by means of melt foaming technique ( mft ). by relative theory analysis and adjusting the content of foam agent, foaming temperature, stirring time and hold time, means of getting samples with high quality has been found
本文採用熔體發泡法，通過相關理論分析和控制發泡溫度、攪拌時間、保溫時間、調節發泡劑含量等制備出了孔結構基本可控、孔洞分佈均勻的閉孔泡沫鋁樣品。 -
Steady array spiral shell pole type penetrate device, two penetrate saturation system, make products to be getting high - quality, melt high - aeeuracily
穩定的直列螺桿式射出裝置，二次射出飽和系統，使產品高品質化，高精密化。 -
The results show that mild melt treatment can improve the bonding strength of coating, but too high temperature and too long retaining time is not suitable ; higher temperature and longer time will result in tin beads separated out from coating surface, affecting surface quality ; melt treatment can reduce the porosity of tin coating, but over 200, the porosity will increase with the rising of temperature
結果表明：軟熔處理會改善鍍層結合力，但溫度和時間不宜過高、過長；軟熔處理的溫度過高和時間過長，表面會析出錫珠，影響表面質量；軟熔處理會降低鍍層的孔隙率，但溫度高於200 ，則孔隙率會隨著溫度的升高而增加。 -
The hot - melt impregnation process of large tow carbon fiber ( 60k ) prepreg to prepare fishing rods is briefly introduced in this paper ; in addition, several typical factors which affect the quality of the prepreg are also discussed in detail here
摘要本文簡要介紹了釣魚竿用大絲束（ 60k ）碳纖維預浸料熔膠膜法浸漬工藝，並著重就影響預浸料質量的幾個主要因素進行了討論。 -
Stable product quality even polyester melt decrease intermediate steps
產品質量穩定，均衡的熔體輸出 -
The results showed that the change of raw material, production load, production process parameters and other abnormal factors will do damage to the melt evenness, spinning stability and yarn quality
研究表明：原料的改變，生產負荷的改變，生產工藝參數的改變及其他一些異常因素都會影響熔體的均勻性，紡絲的穩定性和絲的品質。
分享友人