mold temperature 中文意思是什麼

mold temperature 解釋
模具溫度
  • mold : mold ＝ mould.
  • temperature : n. 1. 溫度，氣溫。2. 體溫。3. 〈口語〉發燒，高燒。
  1. The green body of high quality could be obtained at injection molding temperature from 160c to 180 c, injection molding pressure from loompa to 120mpa, keeping pressure from 40mpa to sompa, mold - temperature 32c, cooled from 2 min to 4 min

    注射溫度為160 180 ，注射壓力為100 120mpa 、保壓壓力為40 50mpa 、模具溫度為32 、冷卻時間為2 4min注射成型后，注射坯的質量較好。
  2. Also the machine mold is up to the required temperature and is usually controlled by thermostat.

    模具應達到所要求的溫度而通常用恆溫器控制。
  3. Abstract : the numerical simulation of the rheological warm extrusion molding of the missile shell, a kind of aluminum alloy part, has been carried out, including the simulation of metal flow in the mold cave, velocity field, stress field, strain field, temperature field, and nodal force etc

    文摘:對鋁合金零件彈托在溫擠條件下的流變成形過程進行了數值模擬，其中包括對金屬在模具型腔中的流動情況、速度場、應力場、應變場、溫度場、節點力等的數值模擬。
  4. The results show that the heat preservation coating and its proper thickness are favorable to the enhancement of filling mold speed of aluminium alloy ; the higher the pouring temperature is and the larger the ratio of hollow areas of vertical pouring is, the faster the speed of filling mold of aluminium alloy is ; if the mold is too thick or too thin, it may decrease the speed of filling mold ; the proper length and the area of vertical pouring are favorable to the enhancement of the speed of filling mold ; although negatire - pressure may improve filling the speed, too high negatire - pressure may enlarge the flaw in casting

    結果表明：保溫塗料及一定的塗層厚度有利於提高鋁液的充型速度；澆注溫度越高、直澆道空心面積率越大，鋁液充型速度越快；模樣厚度太厚或太薄，均會使鋁液充型速度降低；一定的直澆道長度及直澆道面積有利於提高鋁液的充型速度；施加負壓會使鋁液的充型速度大大提高，但負壓過大會增大鑄造缺陷。
  5. The online measurement of mold heat flux can not be replaced by online temperature measurement, the later can respond the uniformity of heat transfer and thickness of solidified shell mote accurately and directly, and online temperature and heat flux measurement of mold can be used to foresee the mold conditions such as fix and scaling of mold

    溫度的在線檢測不能代替熱流的在線檢測，後者可更準確和直接地反映結晶器傳熱和坯殼厚度的均勻性；同時在線檢測結晶器的溫度和熱流有可能對結晶器的設備狀態（如結晶器的安裝狀況和水垢狀況）實現在線預測。
  6. Abstract : thermally induced stress and the relevant warpage cause by inappropriate mold design and processing conditions are problems that confounded the overall success of injection molding. a thermorheologically simple thermoviscoelastic two - dimension material model is used to simulate the residual stress and warpage within injection molded parts generated during the cooling stage of the injection molding cycle. the initial temperature field corresponds to the end of the filling stage. the fully time - dependent algorithm is based on the calculation of the elastic response at every time step. numerical results are discussed with respect to temperature and pressure

    文摘:不均勻的熱殘余應力及其變形是注塑成型加工中常見的工程問題之一.應用熱流變簡單材料的二維熱粘彈本構方程得到的遞推公式，數值模擬了成型中的熱殘余應力及其翹曲變形，並用數值實驗討論了溫度、壓力對注塑件殘余應力及變形的影響，發現溫度變化不均勻是注塑件翹曲變形的最主要原因，其影響遠大於壓力的作用，與工程實驗的結論一致
  7. Maintaining the correct mold temperature becomes more important and may justify mold temperature control equipment.

    保持模具有適當溫度，越來越顯得重要，因而配備模具的溫度控制設備是完全合理的。
  8. Mold temperature is controlled by water flow in cooling channels.

    模具溫度可用冷卻槽中水的流動來控制。
  9. Liquid - solid extrusion of composite material is a new kind of metal forming process, which has been developed in recent years with a promising practical application prospect for its simple working procedure, low cost and good workpiece performance. through a lot of experiments, the optimization and chosing method of key process parameters ( pouring temperature, mold warm - up temperature, impregnating pressure, impregnating time ) has been mastered. under the precondition of appropriate chosing these parameters, the effective control of extrusion velocity is the key of mading good workpiece. but the control of extrusion velocity remains a handwork, and it is heavily affected by such uncertainties as a handler ' s knowledge and skill about the process. in order to solve the problem, the automatic control of the extrusion velocity is studied, and a computer control system is also designed under existing condition

    通過大量實驗，已掌握了關鍵工藝參數（熔液澆注溫度、擠壓模預熱溫度、浸漬時間、浸漬力）的優化選取方法。在合理選取關鍵工藝參數的前提下，擠壓速度的控制是成形出質量良好製件的關鍵。但是，目前對于擠壓速度的控制仍停留在手動控制階段，利用該工藝制備管、棒材製件的成功與否受操作者對該工藝及其設備的經驗及熟練程度等不確定因素影響很大。
  10. A device of measuring the crystallization temperature of mold slag based on single thermocouple wire was introdued

    筆者以保護渣結晶溫度為出發點，提出了一種將雙鉑銠熱電偶絲既作為加熱元件，又作測溫元件的熱絲法技術。
  11. The temperature of the lead should be such that it is just enough to produce satisfactory castings in a heat-stabilized mold.

    鉛液的溫度要正好適宜於在熱穩定的模具中鑄出合格鑄件。
  12. There are many causes, such as fast mold opening, high mold temperature, uneven mold temperature and imbalance of runners

    成品變形之原因相當多，如出模太快模溫過高模溫不均及澆道系統不對稱等。
  13. Profile by frp resins, fibers and a dozen other types of raw and auxiliary materials, manufactured from high temperature polymerization pultrusion. the performance by the quality of raw and auxiliary materials, formula, production control, and different levels of mold

    玻璃鋼型材是由樹脂纖維及其它十余種原輔材料，通過高溫聚合拉擠工藝製造而成。產品的性能受原輔材料的質量工藝配方生產控制模具水平的影響而不同。
  14. Application characteristics ： it ' s made bronze or iron powder, mold pressed under high pressure and then sintered under high temperature, and oil is soaked into the homogeneously spreaded tiny pores of the metal under vacuum

    應用特點：該產品是以銅粉或鐵粉為原料，經模具壓制、高溫燒制、真空浸油后加工而成。
  15. Dryers, mold temperature controller, industrial water chiller, central feeding system, color doses and mixer, stainless steel hopper, heat insulator, metal works, etc. with continuous development over the past years, ming lee now has advanced production equipment, powerful technology, superior production skills and selected excellent import materials

    公司經多年的不斷發展，引進先進的生產設備，擁有雄厚的技術力量，一流的製造工藝，選擇最優質的進口材料，產品具有世界先進水平。
  16. High - temperature manufacturing can speedily fill up the mold and hence reduce molecular orientation. it can also increase the properties of products, but it lengthens the condensation time and increases the injection cycle

    高溫加工可以快速填模，減低分子定位，提高產品物性，但冷卻時間延長而增加註射周期。
  17. Process window analysis, another part of mold flow analysis, examines melt temperature, mold temperature, injection pressure, and fill times

    加工窗口分析、其它零件的模流分析，檢查熔體溫度、模具溫度、注塑壓力和充填時間。
  18. Based on the numeric analysis of the model, the effects of melt temperature, injection time, mold temperature and pre - filled volume on the cell size were studied especially

    在對該數學模型進行數值分析的基礎上，著重研究了熔體溫度、注塑時間、模具溫度、初始填充量對微泡尺寸的影響。
  19. A higher mold temperature can increase the viscosity of melting plastics to run inside the mold. injection in low pressure can also fill the mold for a more perfect product surface and can also reduce molecular orientation for quality properties of the product

    較高模溫可促進溶膠在模內的流動，低壓注射亦能填模，有更完美的產品表面，也能減低分子定向molecular orientation .使產品有更優良的物性
  20. The shrinkage rate of the product is affected by some manufacturing conditions, such as mold temperature, melting temperature, injection speed and the thickness of products

    一些加工條件如模溫，熔膠溫度，注速與產品厚度會影響產品收縮率炮筒溫度cylinder temperatures
分享友人
分享到 Line

分享到臉書