motor nozzle 中文意思是什麼
motor nozzle
解釋
發動機噴管-
14. no warranty will be delivered to such consumables as nozzle, cylinder body caulking, washer, seal ring, o - ring, motor brush, capacitor, bulb, fuse, battery, fan, belt, paper filter element, glass sheet, fuel and lubricant
下列消耗品：噴油嘴缸體堵頭，墊片密封圈o型圈電機刷電容燈泡保險熔絲電池風扇皮帶紙濾蕊玻璃板燃油和潤滑劑。 -
Therefore the output magnetic torque of torque motor can be increased. in this paper, mathematical model of hydraulic flapper - nozzle servo - valve is introduced. the mathematical model of magnetic fluid is built according to the reference introduction
本文給出了噴嘴擋板伺服閥的數學模型，對作用於伺服閥力矩馬達的磁流體數學模型進行了推導，給出了添加磁流體的噴嘴擋板伺服閥的數學模型。 -
Calculation of nozzle efficiency for solid rocket motor
固體火箭發動機燃燒室噴管一體化網格生成 -
This paper described a cold gas simulation of solid rocket motor with submerged nozzle. a two - dimension model with rectangular channel was designed, which can simulate different flow conditions at three periods after ignition
本文從冷流模擬的角度出發，設計了通道為矩形的含潛入噴管發動機冷流模型，可以模擬發動機工作過程中三個不同時刻的流動狀態。 -
The motor case is a steel cylinder closed tight at one end. the other end is the open throat and nozzle.
發動機殼體為一個其一端為密封的鋼鑄圓柱缸體，另一端則為敞口的喉道及噴管。 -
In this paper, simple reacting flow model in solid - propellant ducted rocket combustor based on eddy break - up model is established. the model is used to simulate the three - dimensional combustion flowfields in an experimental motor. some factors how to affect the combustion efficiency are discussed in the paper, including air intake and gas generator nozzle
本文基於簡單反應的旋渦分裂模型，建立了固體火箭沖壓發動機補燃室內的湍流燃燒模型，並在該模型下對某實驗發動機進行了三維數值模擬，研究了補燃室設計參數包括進氣道出口設計參數和燃氣發生器噴管設計參數對燃燒效率的影響。 -
Gap design of solid rocket motor nozzle was analysized through thermal and structure analysis
摘要通過熱和結構計算，對固體火箭發動機噴管縫隙設計進行了分析。 -
However, by comparison with flap nozzle servo valve which has been used widely and popularly by now, the torque motor of jet pipe servo valve has a larger rotary inertia. this causes low natural frequency of servo valve, and thus the response speed of jet pipe servo valve is slow. moreover, the jet pipe of servo valve has large flexibility, and it is easy to excite oscillations and noise in the valve, which is named self - excited oscillations and noise
然而與目前普遍使用的噴嘴擋板伺服閥相比，射流管伺服閥的銜鐵組件轉動慣量大，導致力矩馬達部分固有頻率低，從而響應速度慢，此外，射流管供油管柔性大，容易產生自激現象，這些缺點都使得射流管伺服閥的動態特性差，從而影響了它的工作性能。 -
It will exert resistance and damping force to the torque motor armature, so that the dynamic performance, especially the stability, of flapper - nozzle servo - valve can be improved. the self - excited oscillations and noise can be removed. at the same time, as magnetic fluid has a higher magnetic permeability, the efficiency of torque motor magnetic circuit can be improved
由於磁流體具有的較大磁導率和較大的磁化強度，把磁流體添加到伺服閥力矩馬達的工作氣隙中，可提高伺服閥力矩馬達的磁迴路效率，增加伺服閥的阻尼，從而改善噴嘴擋板伺服閥的動態特性，抑制及消除其自激振蕩和噪聲。 -
Motor nozzle : the product adopts hard alloy or carbon steel heat treatment and receives precision grinding and polishing by professional processing equipment. therefore, it boasts high resistance to flexure and to wear and is extensively applied in fields of series, fan, micro - motor and motor for wire coiling of stator and rotor
產品描述： ：此產品以超硬質合金或碳鋼熱處理為材料，使用專業加工設備精密磨削和拋光加工而成，有極好的抗彎強度、耐磨性，廣泛用於串激、風扇、微電機、馬達等行業的定子、轉子的線圈繞制上。 -
Variation tendency of nozzle gap and contact stress was obtained in terms of multi - time computational results, and some modification suggestions, which are available for designers of solid rocket motor nozzle, were presented by the tendency
綜合多個時刻的計算結果得到發動機工作過程中噴管結構縫隙和接觸應力的變化趨勢，並據此對設計縫隙提出了修改意見，結果可為發動機噴管設計提供參考。
分享友人