plate thickness 中文意思是什麼

plate thickness 解釋
板塊厚度
  • plate : n 1 厚金屬板 〈cf sheet〉 板（片）；（記有姓名等的金屬）牌子，（尤指醫生的）招牌，藏書牌；【印刷...
  • thickness : n 1 厚；粗；厚度；粗大。2 濃度，濃厚，黏稠。3 密度；稠密。4 模糊不清，多煙霧，混濁。5 愚笨；遲鈍...
  1. From the analysis, some suggestion about joint rigidity design is put forward : 1. joint initial rigidity can be enhanced within the limited range when to increase end - plate thickness ; 2. the rigidity and ultimate moment can be enhanced obviously when to adopt the beam with inclined section or to add axilla at the connections between beam and column ; 3. withm the permissive construction condition, exteriorly extended end - plate inclinedly placed is suggested to be applied firstly ; 4. when the rate of joint rigidity to beam rigidity, that is called, is less than 0. 1, the joints can be regarded as zero - rigidity joints ; on the other hand, if is more than 26, it is rigid connection joints

    採用斜截面梁並在樑柱交接處局部加腋能明顯提高節點剛度和梁的抗彎能力； 3在允許的施工條件下，應優先採用外伸式端板斜放節點，有利於提高節點剛度，進而提高節點的抗彎能力； 4節點剛度與其連接構件的剛度比值0 . 1時，可按鉸接節點設計； 26時，可按剛接節點設計。
  2. Since the dry plating does not require the reduction using electricity, the dry plating has many advantages in that it permits to plate the surface of non - conductive polymer materials, and further does not use the electrolyte solution so that wastewater is not produced and the plating thickness can be readily controlled

    由於不要求用電還原，干鍍有許多優點，因為它允許對非導電性聚合物進行上鍍，其次不使用電鍍液，結果不產生廢水，而且鍍層厚度易於控制。
  3. In order to solve the above - mentioned problems, the present invention provides a method for plating a polymer material with a metal film, which can form the film on the surface of polymer materials, which are difficult to plate by the prior wet plating method, at a relatively low cost in comparison to the dry plating method and exhibits a uniform thickness and a good adhesion of the metal film and further, shows a good reproducibility

    為了解決上述問題，本發明提供了一種給聚合物材料上鍍金屬膜的方法，用該方法可以在聚合物材料表面形成膜層，這是原來的工藝難于做到的，而且比干鍍成本低，鍍層厚度均勻，金屬膜的粘附性好，最後，還顯示出好的重現性。
  4. Notice first that there could be a substantial difference between lithosphere thickness and plate thickness.

    首先要注意：巖石圈厚度和板塊厚度之間可能有重要區別。
  5. The factors, such as end - plate thickness, bolt ' s types, beam and column " flank, that can effect on the joint rigidity and moment capability, are analyzed

    分析了節點端板厚度、螺栓類型、端板的加勁肋等因素對節點剛度以及抗彎承載力的影響。
  6. Results after oral administration of gukangning capsule, the mean trabecular plate density, the mean trabecular plate thickness and the trabecular bone volume, bmd and maximum strain of the rats, were significantly increased more than that of the osteoporotic model ( p < 0. 05 )

    結果經骨康寧治療后，骨質疏鬆大鼠的平均骨小梁數、平均骨小梁寬、骨皮質指數、股骨骨密度、股骨的最大變形能力等增加，並明顯高於骨質疏鬆組（ p < 0 . 05 ） 。
  7. The experiments have tested the rigidity of connections that is the m curve of connections, researched two kinds of destruction modes of beam - to - column connections, analyzed stress of the plate and the influence of the member ' s plate thickness, the quantity of self - drilling screws, the diameter of self - drilling screws, the interval of self - drilling screws to the rigidity of connections

    實驗針對連接節點的剛度即連接的m曲線進行了測試，並著重研究樑柱節點的兩種破壞模式，分析了板域的應力分佈以及構件的板厚、連接螺釘的數量、直徑以及螺釘間距對連接節點剛度的影響。
  8. Can all these apparent indications of plate thickness really be mistaken ?

    所有這些關于板塊厚度的明顯標志有可能弄錯嗎？
  9. 4. the elementary analysis about the geometrical parameter influences of plate thickness and breadth of rib beam on mechanical properties of the thin - wall core box cast - in - site concrete hollow floor is also made. a single geometrical parameter on mechanical properties of such floor system is set forth and the fitting scale for these parameters is determined to provide the reference when designing

    4 、對影響薄壁箱體現澆混凝土空心樓蓋內力和變形的板邊梁寬度、肋寬、肋間距、板厚等因素進行了分析，討論了單一幾何參數對該樓蓋受力性能的影響規律，提出這些參數適宜取值范圍，為對這種樓蓋進行設計時提供參考。
  10. Results of the experiment shows that end - plate connections have excellent hysteretic behaviors, and the determination factors, which have crucial influence on the behavior, are end - plate thickness, column web thickness, and the rib stiffeners

    試驗結果表明端板連接具有良好的滯回性能，端板厚度、節點域柱腹板厚度以及加勁肋構造是影響連接性能的主要因素。
  11. Second, on the numerical arithmetic of the quench - induced residual stresses ground, the quenching process of 7075t73 aluminum plate is simulated, the effect of material characteristics along with the plate temperature varying in quenching is considered, and on conditions of the different water temperature and different plate thickness, the quenching processes are compared

    2 、建立了航空鋁合金板材淬火過程的彈塑性力學模型，對航空鋁合金板材溫度場與應力場進行了數值模擬，模擬過程考慮了材料特性隨溫度變化的影響，並對不同的淬火影響因素進行了分析。
  12. It adopts spacing strip cutting. on the fixed cutter frame and mobile frame of the cutter holder, the lifter lifts or presses the upper cutter holder to meet various cutters for different plate thickness. oil cylinder pushes away the mobile frame so as to change cutters quickly

    採用隔套分條機形式，刀軸固定在機架和活動機架上，提升機提升或壓下刀軸，從而滿足不同板厚的刀片重疊;油缸將活動機架推開，便於快速換刀
  13. With the establishment of new model, total 12 finite element specimens, subdivided into 4 groups according to end - plate thickness, bolt diameter and bolt arrangement in two directions, are analyzed

    對12個自行設計的有限元試件進行了計算並對計算結果進行了分析，同時研究了端板厚度、螺栓直徑以及螺栓布置的變化對端板連接強度的影響。
  14. According to the above formula, the initial rigidity and ultimate moment is calculated by developed program to several kinds of gabled frames end - plate connection joint with different types ( such as end - plate connection horizontally placed, vertically placed and inclinedly placed ), different end - plate thickness, different bolt diameter. the different result is compared with different end - plate thickness, the different force arm in joints, different bolt diameters and strength grades

    按推導的公式編程計算了不同形式（端板外伸式、端板平齊式、端板斜接、柱腹板加勁） 、不同端板厚度、不同螺栓直徑的門式剛架樑柱端板節點的初始剛度、節點極限彎矩，並比較了不同端板厚度、不同節點力臂、不同螺栓直徑和強度等級、不同連接形式下初始剛度和極限彎矩的變化。
  15. Steel plate thickness meter

    鋼板測厚儀
  16. The side displacement of the glass plate center is larger or less than the glass plate thickness, for the 3d geometric size of the glass plate and the lateral load vary in a wide range. in other words, the mechanic analysis of glass plate belongs to large deflection or small deflection theory in thin plate theory

    由於幕墻玻璃的三向幾何尺寸和橫向荷載集度可在較大的范圍內變動，玻璃板中心的側向位移，有可能小於或大於玻璃板的厚度，也就是說，幕墻玻璃的力學分析，既可能屬于薄板理論中的小撓度問題，也可能屬于大撓度問題。
  17. This means that inferences regarding the depth extent of such anomalies are no measure of plate thickness.

    這意味著關于這種異常深度范圍的推測並不能測定板塊的厚度。
  18. Plating method, cylinder or matthews, depends on customer request, printing plate thickness could be appointed by customer

    圓柱卷版方式或歐式matthews裝版方式，可依客戶要求製作。
  19. Allow plate thickness and standard deviation shall meet the requirements for their products. beam deviation should be allowed to meet the size and specifications of their products standards

    鋼板厚度及允許偏差應符合其產品標準的要求.型鋼的規格尺寸及允許偏差應符合其產品標準的要求
  20. Based on the experimental and numerical simulation results, a new equivalent plate thickness formula and new empirical formulas for the mean crushing load are given

    基於實驗結果和數值模擬的結果，給出了新的等效板厚和平均壓潰載荷計算公式。
分享友人
分享到 Line

分享到臉書