possible deviation 中文意思是什麼
possible deviation
解釋
可能離差-
According to avestan belief, there is no reversal and no deviation possible once a man has made his decision
通過對《阿維斯陀》的信仰，人一旦作出了他的選擇，就沒有顛倒和背離的可能。 -
Although the accuracy in meterological forecast of tropical cyclones has been distinctly improved, it is still a difficult problem confronting masters and anti - typhoon team leaders of the companies how to steer clear of typhoon reasonably and safely in case that the actual resistance to typhoon is strong enough, the sea area wide enough, and the time permitting ; to avoid unreasonable deviation, anchoring for shelter, blindly rushing onto her path, being involved in storm area, even into the the center of typhoon ; under the limitation of the condition of the sea area and time. how to take correct meassures to escape, such as navigating with wind or windward in bias angle, slowing down, anchoring, berthing alongside the warf, mooring to buoy, etc. as early as possible
盡管氣象部門對熱帶氣旋監測預報的準確率已經比過去有了明顯的提高，然而船舶在海上如何避離臺風，如何做到在本船實際抗風能力允許、海域條件允許、時間也充裕的前提下合理避臺，安全避臺，避免不合理的繞航、 「扎風」 ，避免盲目冒進「搶風頭」 ，更避免被捲入強風區甚至臺風中心；在海域條件受限、時間尷尬的情況下又如何正確採取偏順航、偏頂航、滯航、錨泊、系岸、系浮等抗臺措施和技術，盡快擺脫臺風的影響，仍然是擺在船長和公司防抗臺領導小組面前的一個實實在在的難題。 -
The following conclusions are gained : ( 1 ) the located shear band prongs the ligament near the top crack tip and the structure may occur shear - mode fracture at the angle of 155 ? to crack when load is 87. 92mpa ; the mode of fracture of the flange joint structure is not possible to be void - mode ; ( 2 ) it is proved that loading and then unloading repeatedly can not increase the possibility of invalidation of the structure when the times of loading and unloading are not too more when load is operating pressure ; the structure is safe when the vessel is operating ; ( 3 ) in the fe model of the thesis, not considering the influence of water pressure test which is in the process of fabrication of vessel in fe results in larger deviation in analysi
得出了以下結論：在8792mpa的載荷下筒體一封頭連接結構處的集中剪切帶貫穿韌帶，可能發生沿與原裂紋線成155 「角方向剪切型斷裂；筒體一封頭連接結構不可能發生韌窩型斷裂； （ 2 ）在工作壓力下進行次數不多的反復加、卸載，結構不會破壞，也不會喪失安定性：結構在工作狀態下是安全的； m在本文的彈塑性有限元模擬計算中，對于裂紋尖端進行力學分析時，不考慮壓力容器製造過程中水壓試驗的影響，將導致計算結果出現較大的偏差； （ 4 ）筒體完全屈服時的載荷為92石3mpa ，封頭完全屈服時載荷為86 -
The possible factors including the deviation of temperature in length and breadth of rod, the changes of transfiguration resisting force under the changes of temperature, the adjustment of roll gap, the variation of rolling pressure, the changes of roller speed during dynamic adjusting press, the unmatched of seconds - flux under the dimension fluctuation of the coming sample and so on. the whole system was a closed loop which factors in it interacts each other
可能的影響因素有:沿軋件縱橫向溫度變化、由溫度引起的軋件變形抗力變化、軋機輥縫值變化、負載變化、電機調節系統由不穩定向穩定過渡過程中軋輥轉速的變化（如咬鋼過程中的動態速降后的回復階段） 、來料尺寸波動造成秒流量不匹配等，整個模擬系統是各個因素相互影響關聯的一個閉環系統。 -
He now bore off to the right to counteract the possible deviation from his true course
為了修正對正確路線的偏離，現在，他要朝右開始他那一搖一晃的行程了。 -
Maximum possible margin of population deviation
可容許的人口相差幅度上限
分享友人