running shaft 中文意思是什麼
running shaft
解釋
旋轉軸-
In other words, the regular side of the cam shaft and the fuel running of the main engine are interlocked with each other
換句話說，凸輪軸的調油側與主機的燃油運轉是相互聯鎖的。 -
Pump shaft is provided with independent supporting point to ensure dependable running of motor bearing
泵軸有獨立的支撐點，使電機軸承運行可靠。 -
Analyze item by item the position of unintact cycle, the running clearance of unintact cycle, locking - deform, datum dimension regulating, repeatly install, power voltage wave and marking running etc. at the same time, we give the calculating formula to calculating the running marking random error, and use it to calculate the system error of big diameter measure instrument - - datum dimension frame error, gyro - wheel diameter error, error caused by circumstance temperature, error caused by backing distance, angle error, delay error of data collecting circuit, lathe main shaft running error, workpiece install partial error
對不完整圓的位置、不完整圓的轉動間隙、鎖緊變形、基準尺調整、重復安裝、電源電壓波動、標記轉動等隨機誤差進行了逐項分析，並給出轉動標記隨機誤差的計算公式。對大直徑測量儀的系統誤差?基準尺尺架誤差、滾輪直徑誤差、環境溫度引起的誤差、後退距離引起的誤差、角度誤差、數據採集電路延時誤差、車床主軸回轉誤差、工件安裝偏心誤差分別進行了計算，最後對誤差進行合成。 -
In the third chapter, the mathematical models of project system have been established, and simulation has been done on the simulink enviroment of matlab software kits. the simulation focus on the effects of main parameters on the dynamic characteristics of speed control system, and the main parameters include viscosity damp coefficient and friction torque of electrical motor shaft, internal leakage coefficient of pump / motor of hydraulic circuits, gas volume of pressure accumulator, viscosity damp coefficient of cylinder piston and different running building floors, etc. at last, theoretical research effects of the flow and pressure pulsation of pump / motor on car speed and oil volume leakage theory are discussed. the fourth chapter of this thesis concerns the research on the key items about hydraulic power control system according to the ens 1 - 2 and other hydraulic elevator standards
論文第三章針對組成系統的各個模塊進行了機理建模，並且通過matlab軟體中的simulink圖形化模擬環境進行了本課題系統的模擬研究，主要針對影響系統特性的主要參數變化，動態分析系統的輸出特性，在上下行工況中，分析了電機軸系粘性阻尼系數、軸系摩擦力矩、主迴路蓄能器迴路液壓泵馬達內泄漏系數、蓄能器氣體容積、液壓缸柱塞粘性阻尼摩擦系數以及不同運行樓層工況等參數對系統特性的影響；最後對軸向柱塞泵馬達的流量壓力脈動對電梯轎廂速度的影響和蓄能器內油液體積損失機理進行了理論研究。 -
If the using abrasion speed is low and the loading is not very big, but it undertakes heavy impact when running, it is better to apply thick wall shaft liner, for if the wall is too thin, the rigidity is not enough
如果使用滑動磨擦速度較低，負載不是很大，但運轉時受很大的沖擊，此時應採用厚壁軸套。如果軸套壁薄，剛度不足，可與金屬外套復合使用。 -
A motor that is be directly coupled to a fan - blade or blower - wheel load is to be operated at the applicable test voltage and under no - fan, no - load conditions with the shaft running free
直接耦合到一個風扇葉片或鼓風機葉輪負荷的馬達，將在適用的試驗電壓下做無風扇，無負荷，軸空轉狀態的運行。 -
The quality of shaft alignment, is of vital importance in ensuring the long term appropriate running of shafting system and shortening the construction period of shipbuilding, also crucial in keeping the sailing vessel in the set course
船舶軸系校中的質量，對于確保軸系長期正常地運轉和縮短船舶修造周期都非常重要，也是船舶正常航行的關鍵。 -
The shaft liner only works intermittently, when it stops running, it generates no heat, but the radiation is continued
軸套只做間歇式工作，在停止工作這段時間內並不產生磨擦熱，但散熱仍在進行。 -
In order to make the full use of the facility to maintain the machine rotating system, the alternative excitation setting, which remains by altering the excitation setting, is changed into subsidiary generator running on the same shaft. and it can enhance the work capacity of the whole unit
為了充分利用設備，保持原機組的機械旋轉系統狀態，現將勵磁系統改造后空余出的交流勵磁機改為同軸運轉的副發電機，增加整體機組的工作容量。 -
The working condition of nylon shaft liner is determined by many factors, for example : the different formula, shaping technique, the design of shaft liner, installation method, loading features, running speed, lubricant condition, the working environment of shaft liner temperature, humidity and the influence of impurity, abrasion when working etc. so, when designing shaft liner, it is necessary to take consideration of all conditions
鑄型尼軸套的許用工作情況是由很多因素決定的，例如不同配方和成型工藝所制得的材料物理機械性能，軸套的設計裝配方法，負載特點，運轉速度，潤滑情況，軸套的工作環境溫度濕度雜質的影響，工作時的摩擦條件，對磨材料的性能等。因此，在設計軸套時，應綜合考慮各個方面的因素。 -
Requirements on agitator drives ; agitator speed and direction, bearing application running accuracy, dismounting space for shaft seal
攪拌器傳動裝置的要求.旋轉速度和旋轉方向，軸承應用 -
Running test of shaft generator and clutching test between m. e. and shaft generator
軸帶發電機運轉試驗及主機與軸帶發電機之間的離合器的效用試驗。 -
To take an actual example, the triple pipe method has been adopted to consolidate the surrounding soil by rotary shot grouting pile and swaying shot diaphragm wall in the construction of vertical shaft and access drift of running tunnel from martyr ' s park to dong shan kou station in no. l line of guangzhou metro. it turns out that this method has met the double effect of both construction support and waterproof
作為施工實例，在廣州地鐵一號線烈士陵園至東山口區間隧道的豎井及聯絡通道施工中，採用三重管法對周圍地層實施了旋噴樁和擺噴墻加固，達到了施工支護和防水止滲的雙重效果。 -
In order to achieve effect running without fault, the max running pv value should be limited in 0. 220. 24 ; under oil lubricating circulating or the shaft liner runs in oil, the max running pv value reaches 2. 5 even above, for the radiation is fine
為保證使用中不出現問題並有效的工作，應控制最大許用pv值在0 . 220 . 24之間在有循環油或者軸套在油中使用時，最大許用pv值可提高到2 . 5甚至2 . 5以上，因為這種情況散熱情況良好。 -
At this time, the temperature of the shaft liner will reduce gradually, if the working time is shorter than the running time, the heat rising is low and the pv value is high
此時，軸套的溫升就逐漸下降。如果工作時間短於停止時間，則蓄熱少，溫升低，許用pv值就高些。
分享友人