sample strength 中文意思是什麼
sample strength
解釋
樣品放射性強度-
Based on the analyses on mechanical properties, microstructure and fracture of - the microalloyed steels socrv with various heat treatment technique, it can be affirmed that various fractures arttribute to various mechanism, we can draw conclusion that the strength and toughness of microalloyed steels 50crv will be increase simultaneously by optimal heat treatment technique. to illustrate the mechanism of the strength and toughness of microalloyed steels socrv, we designed the comparative experiment and observed the microstructure of the sample which occurred at different quench and tempering temperature and different tempering time. the last experiment results were determined by the four factors : fined microalloyed elements grains, the decompound of martensite, martensite transformation of remnant austenite and the second phase precipitation
為解釋微合金化50crv鋼強韌化機理，本文通過對不同淬火溫度，回火溫度，回火時間下的力學性能指標的對比及顯微分析，認為微合金元素的細化晶粒，馬氏體的回火分解，殘余奧氏體的轉變，第二相的沉澱析出共同決定了微合金鋼的強韌化情況，特別是由於微合金元素的存在，其細化晶粒及其碳氮化物的沉澱析出，導致鋼的良好的強韌性，並且如果工藝滿足第二相的沉澱析出強化大於回火馬氏體分解引起的軟化效應，會在硬度曲線中產生明顯的二次硬化現象。 -
When fillings is other materials ( unprocessed montmorillonite, powder coal ash, co - composite of powder coal ash and organo - montmorillonite, co - composite ofcarbonizing calcium and organo - montmorillonite ) in the binder and content of organo - montmorillonite in the binder is five percent decided by tensile - shear experiment, tensile - shear strength of binder is up to tiptop ; at the same time, this paper carries out abrasion experiment, and, by comparison, concludes abrasion property of coating is optimum when content of organo - montmorillonite in the binder coating is five percent, and observes abrasion sample under set
當膠粘劑中填料為其它物質（未處理蒙脫土、粉煤灰、粉煤灰和有機化蒙脫土共復合、碳化鈣和有機化蒙脫土共復合）時，通過拉伸剪切試驗確定膠粘劑中有機化蒙脫土含量為5時，膠粘劑的拉伸剪切強度最高；同時進行了沖蝕磨損試驗，通過比較得出，當膠粘劑塗層中有機化蒙脫土含量達到5時，塗層的耐沖蝕磨損性能最佳，並對沖蝕磨損試樣在掃描電子顯微鏡（ set ）上進行觀察。 -
The pouring tests of the ladder foam sample were made in silica sand, chromite sand and zircon sand the results show that zircon sand and chromite sand have the better chilling effect, and the structure of the aluminum alloy is finer, the hardness and strength has large improvement, subsequently the investigation provides the reference for manufacturing aluminum alloy thin thickness mold with excellent quality
結果表明，鋯英砂和鉻鐵礦砂具有較好的激冷效果，得到的鋁合金鑄件組織細小，強度、硬度有較大的提高，為薄壁隨型、質量優異的鋁合金消失模模具製造提供了技術依據。 -
Failure probability of coarse aggregates ( pfca ) could be a sample index durability evaluation of concrete in compressive strength test, where pfca was the ratio of number of total particles to which of the broken ones of coarse aggregates in the failed faces of a concrete specimen
混凝土抗壓試驗中，粗集料破碎率p _ （ fca ）可以作為混凝土耐久性的一個簡要評價指標，其定義為試件斷裂面上破碎的粗集料顆粒數與暴露的粗集料顆粒總數之比。 -
The experiment procedure and analysis result about exteriorly extended end - plate connection with high strength bolt are introduced primarily ; each sample ' s dimension is given. the adding load equipment, measuring apparatus placed, measuring point established is detailed. adding load measure load and m - curve is produced ; the single span gabled frames horizontal displacement formula is deduced when the horizontal concentrated force is applied to it
重點介紹了外伸端板高強螺栓連接的實驗過程及實驗分析結果，介紹了各組試件的形狀尺寸、加載裝置、測量儀器安放、測點的布置等；給出加載方式及測出的m -曲線；計算出試驗節點的初始剛度；推導水平集中力作用下單跨門式剛架考慮節點半剛性的側移計算公式。 -
The results indicated that the dimension, shape and purity of base material could meet the functional demand of solid lubricant ; the thermal decomposition temperature of ptfe resin exceeds 400 c, but organic and inorganic packing filler added in ptfe made the water absorption rate of composite material increased, melting temperature and decomposition temperature decreased, in the meanwhile oxidative decomposition reaction was accompanied ; polar groups such as c = o, c - o - c and so on in the carbon fiber surface is advantageous to increase compatibility with other components and interlayer shearing strength ; uniform design experimental method could help to find the relationship between formula and frictional property by relatively small tests. the developing trend of each formula ' s friction coefficient could be showed by fitting curve ; the friction coefficient with no copper powder or graphite in formula was relatively big. this fact showed that copper powder and graphite should be used cooperatively ; it was found that when the ratio of copper powder to graphite by weight is 15 : 60, 30 : 30 - 40 and 60 : 15 - 30 respectively, the friction coefficient was relatively small. the degree of crystallinity of pure ptfe reached maximum by air cooling and the abrasion loss also reached maximum among three ones ; at the same time, the abrasion loss of solid lubricant sample was also the biggest among three ones ; when solid lubricant matched with 45 # steel axle or gcrl5 steel axle, lubricant transfer film could be formed on metal surface, thus direct contact between the surface of metal friction pair rings was reduced. their working life was elongated extremely ; there was mainly much graphite, a little ptff, moo3, feso4, cus and so on in lubricant transfer film
試驗結果表明：所選原料的尺寸、形狀及純度可滿足固體潤滑劑的性能要求；聚四氟乙烯樹脂熱分解溫度超過400 ，但在ptfe中加入無機填料會使復合材料吸水率提高，熔融溫度及分解溫度降低，且伴有氧化分解反應；碳纖維表面含有c = o及c - o - c等極性基團，有利於提高其與其它組分的相容性，提高層間剪切強度；均勻設計試驗方法能夠用較少的試驗次數找出配方與摩擦性能間的關系，擬合曲線基本能表示各配方的摩擦系數發展趨勢；配方中不加銅粉或不加石墨，其摩擦系數均較高，說明銅粉和石墨應該配合使用；當銅粉15份、石墨60份時，銅粉30份、石墨30 - 40份時，銅粉60 、石墨15 - 30份時，摩擦系數均具有較低值；純聚四氟乙烯樹脂在空氣冷卻時結晶度最大，磨損量也是三者中最大的；同時，固體潤滑劑試樣在空氣冷卻時的磨損量也是三者中最大的：不論是固體潤滑劑與45 #鋼軸配副或是固體潤滑劑鑲嵌入銅套后與gcr15鋼軸配副，在金屬表面均可形成潤滑轉移膜，從而減少金屬摩擦副表面間的直接接觸，大大延長其使用壽命;轉移膜中主要含有較多的石墨、少量聚四氟乙烯、 moo 。 -
2. tinting strength compared with standard sample
1色光與標準樣品比 -
Barrier cracks cannot stop the extending of a fracture, and the strength of the sample is reduced by almost one magnitude because of the existing barrier cracks. there are great differences of ae distribution between specimens with non - penetrate crack and specimens with penetrate crack. as for penetrate crack, ae occurs near the two end of the crack, and for non - penetrate crack, crack, ae occurs near the two end of the crack, and for non - penetrate crack, ae occurs near the front edge of crack, which can be explained well by the theory of 3 - d fracture ; ae distribution near the outer part of collinear crack is similar with that of the end of penetrate crack, and inner part of collinear cracks will run - through with high loads
關于預制裂紋系對巖石破裂的影響，集中討論了：空障礙體構造不能阻止主裂紋的擴展，反而會使巖石的破裂強度降低近一個量級；由於構造的不同，非穿透切口樣品和穿透切口樣品的聲發射空間分佈特點有本質區別，穿透切口樣品的微破裂在切口兩端發育，而非穿透切口樣品的微破裂在切口兩端之間切口前緣處發育，這用三維破裂理論可以很好地解釋；含共線構造的巖石，裂紋外端的聲發射分佈與單裂紋構造中裂紋端部的聲發射分佈相似，裂紋內端聲發射有密集分佈，在應力達到一定水平時，內端部發生錯斷，而不是貫通。 -
This formula used inverse regression and data fusion technical and maximum likelihood theory, then this method enabled random sample value obtained in ultrasonic and rebound method of different detection population to mix together effectively, and reach estimation of concrete strength
該公式利用逆回歸理論、數據融合技術和最大似然原理，將回彈值和聲速值分別看作被解釋變量，將來自超聲法和回彈法不同量綱的檢測數據進行有效融合，得出混凝土強度的推定值，該推定結果具有無偏性和方差最小性質。 -
The subject interpreted the feasibility of crash and separating of rock and charcoal by doing a lot of experiments. it also interpreted the fluctuation of a single sample and the stability of all the samples. the strength of a single waste rock and charcoal was more fluctuated, but on the whole it trends to stable
也即在煤矸實驗中單獨就一塊煤、矸來講其強度是特別離散，但從整體一批礦塊來講其強度服從一種正態分太原理工大學碩士學位論文布，其強度整體上趨於一個穩定值，從大量的實驗說明了這一點。 -
Verification of concrete strength ( destructive ) by coring - sample of concrete is cored cut, capped strength of the in - situ concrete
用作證明混凝土之強度-從現聲場鉆孔取樣板以作搞壓試驗，從而印證混凝土之強度。 -
The working stress of the rc compression member in existing structures can be calculated through measuring strain change before and after drilling the hole, determining the compressive strength and elastic modulus of concrete through the drilled sample and combining the calculating results of the finite element method
該方法通過測試鉆孔前後孔邊應變的變化，利用鉆取的芯樣推定混凝土的抗壓強度和彈性模量，再結合有限元計算分析，得到已建結構中鋼筋混凝土受壓構件的工作應力。 -
On the basis of spot sample and laboratory experiment, authors studied the time - variant probability model early age period mechanical properties of high - strength concrete
通過現場試驗建立了高強度混凝土早齡期力學性能的經時概率模型。 -
The test result of the rene95 sample showed that the maximum ultimate tensile strength can be as high as 1400mpa and has reached 97. 9 % of that of the sample fabricated by powder metallurgy ( pm ). the plastic elongation of the test sample can even exceed that of pm. the ultimate tensile strength of the test sample grown from single crystal substrate has surpassed 6 % of that of grown from the stainless steel substrate, at the same time the plastic elongation surpassed 40 %
對成形試樣的力學性能測試結果表明，強度方面_ b最大為1400mpa ，已經達到了粉末冶金的97 . 9 ，塑性方面甚至超過了粉末冶金的水平；以單晶為基材的成形試樣其最大拉伸強度要比不銹鋼為基材的試樣高6 ，延伸率要高40 。 -
The conclusions have been deduced from the detailed analysis of a set of experimental results as below : 1 ) the formula of tangent young ' s modulus et has been established during the unloading process ; 2 ) the shearing features of the samples are similar to undrained test even though there are draining paths so the possion ratio of the sample is about 0. 5 ; 3 ) unloading paths have little effects on the shearing strength parameters
通過對試驗結果的分析得到： 1 ）任一時刻土體的切線彈性模量公式； 2 ）卸載情況下盡管存在排水通道，但試樣仍基本上表現為不排水的性狀，按廣義虎克定律得到的泊松比在0 . 5附近； 3 ）卸荷應力路徑對土體的強度參數影響不大。 -
The cfrc sample is always ruptured in the place where materials weakly resist outside force, and because the cracks " or damages " distribution of cfrc is random, bending strength of cfrc takes on dispersed
本文最後採用weibull統計理論對裂紋鈍化后的cfrc的抗彎強度進行了評價，通過最弱環原理解釋了weibull模數的力學意義以及它與cfrc材料中裂紋的關系。 -
Abstract : with the graphite content adjusted, a friction performanceexperiment is carried on the iron - base powder alloy brake material sample. the results show that the graphite increases with the decrease of the strength and the static friction coefficient of the material, while the dynamic friction coefficient increases correspondingly
文摘:調整鐵基粉末合金剎車材料中的石墨含量，製成摩擦試樣進行摩擦性能試驗，結果表明材料中石墨含量增加，其強度會隨之下降，摩擦系數也隨之下降，而動摩擦系數則隨之上升。 -
With the graphite content adjusted, a friction performanceexperiment is carried on the iron - base powder alloy brake material sample. the results show that the graphite increases with the decrease of the strength and the static friction coefficient of the material, while the dynamic friction coefficient increases correspondingly
調整鐵基粉末合金剎車材料中的石墨含量，製成摩擦試樣進行摩擦性能試驗，結果表明材料中石墨含量增加，其強度會隨之下降，摩擦系數也隨之下降，而動摩擦系數則隨之上升。 -
Abstract : it was studied by us that new technologies using strong pulsed magnetic field and electric current were applied to refine metal ' s solidified structure. these technologies improved remarkably the solidified structure of ly12 aluminum alloy and made the solidified grains more equiaxed and apparently finer compared with that of the normal sample, which is of more dendrite grains. the stronger the strength of the pulsed electromagnetic field, the better the improvement effect was. the refinement mechanisms of the new technologies were analyzed theoretically. new phenomena and problems occurred in our experiments were also pointed out in this paper
文摘:提出了用強脈沖磁場和電流細化金屬凝固組織的新工藝.與未經磁場或電流處理的凝固樣品相比，強脈沖電磁場能夠顯著地改善ly12鋁合金的凝固組織，使晶粒明顯細化、球化，電磁場的強度愈強，這種改善效果愈明顯.對該新工藝的細化機理進行了理論分析，同時，指出了實驗中的新現象和新問題 -
The sample holder ' s z - axis adjustment makes it easy to find the maximum signal strength, and a safety cover rotates when needed to block the laser
試樣夾在z軸方向上的調整使其能夠方便地發現最大信號強度，此外，當需要阻斷激光的時候安全保護罩將會旋轉。
分享友人