section pipe 中文意思是什麼
section pipe
解釋
吸油管-
The research of acoustic wave in different - section resonance pipe
變截面共振管的聲特性研究 -
The influencing factors of coal arch camber in planomural coal bin and coal drop pipe with rectangular or circular cross section during coal drop are studied theoretically
摘要對落煤過程中平壁煤倉及截面形狀分別為矩形、圓形的落煤管起拱的影響因素進行理論研究。 -
The following are the large projects undertaking by haifeng company : crude oil electricity plant project of north china oil field hydroelectricity factory, apartment ( 22 stories ) of yuanda real estate company of dalian shipping group, helios hotel of helios group in dalian development zone, tilt aqueduct bridge of shanxi hongqi reservoir ( total span : 267m ), supply and sale building and city construction building ( both are antique architectures ) of shanxi heyang city, sea drainage pipe of hainan fudao fertilizer factory ( 1520 ), 8 oilgas docks of hainan haiyan oilgas company, basha condensable gas transfer station of haiyan company, 10, 000m3 oilgas storage tank of arco company ( usa ) in hainan nanshan, gas pipe and fuel gas installation project of hainan nanshan electricity co., ltd, base and accessory project of hainan gas company, bei da huang cereal and oil market in harerbin, hainan cross island pipe, changhuajiang river pipe crossing project, taihangshan mountain earthwork project ( the 19th section of west - to - east gas transmission project )
海南海峰公司承建大的工程項目：華北油田水電廠原油發電站工程；大連船泊集團遠達地產公司的遠達公寓（ 22層） ；大連開發區香港太陽神集團的太陽神大酒店；陜西紅旗水庫斜拉渡槽工程（全跨267m ） ；陜西合陽供銷大樓及城建大樓（均為仿古） ；海南富島化肥廠排海管線（ 1520 ） ；海南海燕油氣公司八所油氣碼頭；海燕公司白沙液化氣中轉站；海南南山美國阿科公司儲油氣萬立米大罐工程；海南南山電力股份有限公司天然氣管線及燃氣安裝工程；海南南海天然氣有限公司基地及配套工程；哈爾濱北大荒糧油批發市場；海南環島管線；昌化江穿越工程；西氣東輸十九標段，太行山土石方工程。 -
Firstly, simulate flow field of rear smoke channel, plot velocity magnitude and ash concentration distribution in section of entry of heat pipe air preheater, compare with data which were measured in guiyang power station, verify simulation to be reasonable and right. secondly, simulate all kinds of factors which affect flow field ' s uniformity such as length, thickness, location of diffluent board, ash concentration, ash diameter, and so on, find the chiefly factors. thirdly, install guide board in curve channel in rear smoke channel, then simulate its " flow field, plot velocity magnitude and ash concentration distribution
在此基礎上模擬在冬夏兩季不同情況下，不同流速對熱管空氣預熱器壁面溫度的影響；然後對影響整個流場分佈的各種因素：包括分流板長度、厚度、偏離中心流道位置的偏離度、飛灰濃度、飛灰粒徑等因素進行數值模擬；最後提出在分流煙道轉彎處加裝導流板，並模擬加裝導流板后的流場分佈，得到下級空氣預熱器出口、熱管空氣預熱器進口處的斷面速度場分佈、濃度場分佈，以論證加裝導流板能達到流場均勻化的作用。 -
With the fea software ansys and shell element which has high - precision, this dissertation optimize the size and thickness of skeleton section and seek steel pipe which still have strength and stiffness surplus under static state working condition : sinkage of 240mm of rear wheel. it ' s fully loaded in the state of static bending and torsion. after that, amelioration is achieved for even strength design
本課題運用ansys有限元分析軟體，並且使用精度較高的shell殼單元作為建模單元，在靜態條件下，通過對左右後輪下沉240mm的彎扭聯合工況的模擬分析，尋找出骨架中存在強度和剛度富裕的構件，使之達到輕量化改進的目的。 -
The plumber splayed the end of the pipe before fitting it over the next section
鉛管工把管口撐大套在另一截管子上 -
Backing weld procedure technique of all - position narrow gap and thick - walled pipe welding is developed about all - position single - pass welding section analysis, wire feeding behavior, weld arc length, welding current analysis, procedure and joint test. the achievement has general guide meaning to producing and testing all - position welder
從單焊道全位置區段、送絲行為、焊接弧長（電壓） 、電流行為分析、工藝試驗和接頭檢驗等幾方面介紹管道全位置打底焊工藝特點，其研究成果對全位置焊接機的製造和調試具有普遍指導意義。 -
Abstract : backing weld procedure technique of all - position narrow gap and thick - walled pipe welding is developed about all - position single - pass welding section analysis, wire feeding behavior, weld arc length, welding current analysis, procedure and joint test. the achievement has general guide meaning to producing and testing all - position welder
文摘:從單焊道全位置區段、送絲行為、焊接弧長（電壓） 、電流行為分析、工藝試驗和接頭檢驗等幾方面介紹管道全位置打底焊工藝特點，其研究成果對全位置焊接機的製造和調試具有普遍指導意義。 -
A reasonable position of driving nozzle helps to achieve the maximum material flow that also depends on other parameters such as backpressure, properties of conveyed material and driving gas. it is observed that, an increase of convergent section angle is harmful to the pneumatic conveying system, and also influences on the mass flow rate of conveyed material, the distribution of static pressures in injector and the pressure drops of conveying pipe. in addition, within a reasonable scope of air mass rate, increasing the driving jet velocity is more advantageous than enlarging the dimension of driving nozzle
試驗研究發現，氣體噴嘴位置對氣固噴射器的輸送能力影響最大，氣體噴嘴存在某一最佳位置，而這一最佳位置與背壓、輸送物料特性和輸送風特性相關聯；氣固噴射器的收縮角對其輸送能力、內部靜壓分佈和輸送管阻力特性均有適量影響，收縮角增大對整個輸送系統均不利；在適當的輸送風范圍內，提高氣體噴嘴出口速度比擴大氣體噴嘴尺寸更為有利，但氣體噴嘴出口速度過高會增加氣固噴射器和輸送管內的能量損耗，給輸送帶來不利的影響；系統背壓與氣固噴射器的氣體噴嘴出口速度的選取有關。 -
When f is about fr, for curved pipes, the secondary flow appears eight vortexes for annular cross section and four for circular and four or six for elliptical ; for helical pipe, the secondary flow appears as a loop flow for annular and circular cross section, and a saddle flow for elliptical cross section
當f在fr左右時，對于彎管，環形截面上存在八個渦，圓截面上存在四個渦，橢圓截面上存在四個或六個渦；對于螺旋管，圓截面和環形截面上二次流表現為環流，橢圓截面上表現為鞍流。 -
Based on the review, the fluid flow and heat transfer in the curved circular and rectangular pipes have been researched by employing perturbation method and numerical simulation with a physical model under the rotational orthogonal curvilinear coordinate in a rotating curvilinear pipe with multi - parameters. we firstly analyzed the fully developed fluid flow and heat transfer, mixed convection heat transfer, the development of flow and heat transfer in the inlet in different cross section ( circular, elliptical, annular and rectangular crossection ). the variations of the secondary flow, axial velocity, distribution of temperature, the friction force on the wall, the ratio of friction factor as well as the nusselt number with different dimensionless parameters had been examined in detailed
本文在總結和分析了一個世紀以來有關曲線管道流動和換熱特性的研究成果的基礎上，以旋轉正交曲線坐標系統下的多參數旋轉螺旋管道中的對流傳熱為物理模型，通過攝動方法和有限體積法，首次對各種截面（圓截面、橢圓截面、環形截面、矩形截面）旋轉曲線管道內充分發展流動的流動結構和傳熱特性（包括耦合對流傳熱特性）以及旋轉曲線管道開口段發展流動的流動結構和換熱特性進行了系統的數值模擬和理論分析，詳細討論了各種無量綱參數對管道內軸向速度分佈、二次流結構、溫度分佈、壁面摩擦力、摩擦系數比以及管道nusselt數的影響，獲得了若干創新性成果。 -
For the pipe section with natural gas hydrates formed, several effective methods to treat ngh are suggested to use, that is, depressurizing as fast as possible ; heating the pipe ; injecting methanol / ethylene glycol and venting
指出對已形成水化物的管道段，可採取盡快降低運行壓力、加熱、注醇和放空等措施進行處理。 -
In order to achieve the optimized tunneling approach, first, tunneling procedures, shift length, horizontal jet grouting length, bench length and space length between c and d part of crd method are optimized ; on the basis of these results, two kinds of tunneling schemes are calculated with three - dimensional fem and the optimized tunneling scheme is achieved. as results of the optimized scheme, the conclusion is made that the gas pipe above the tunnel of sk3 + 355 section is secure. the calculation results are verified through comparison of numerical simulation results and site - monitoring measurement data
為得出適合本段工程的最佳施工路線，利用大型有限元通用軟體ansys對開挖順序、開挖進尺、水平旋噴長度、臺階長度及crd工法施工的c 、 d部相錯長度進行了有限元數值模擬和優化分析，並利用這些分析結果，進行了兩個施工方案的三維有限元動態施工模擬，得出了較優的施工方案，並利用施工后的地表沉降槽曲線，對sk3 + 355斷面處隧道上方的煤氣管線的安全性進行了分析，得出了利用此施工方案施工不會造成此處煤氣管線破壞的結論。 -
( 2 ) respectively by elastic theory analyses and methods of structural mechanics, transverse static analytical equations for flexible pipeline rigid pipeline are established whose outcomes are applied in numerical example to compare those with that by finite element method. ( 3 ) considering interaction of filled soil, pipeline and foundation, with an eye to non - linear soil model, in view of the initial geo - stress field and the effects of interface between soil and pipeline, and by finite element method the calculational model and method are built for transverse stress in pipeline. then, by the great finite element analytical software ansys, those outcomes are applied in calculation example of positive buried pipe to educe the distribution of circumjacent soil pressure and stresses on cross section and to compare it with that calculated by conventional ways before those outcomes are applied in engineering case of positive buried pipe with flexible filled materials to confirm distribution of soil pressures after the measure for reduction and to compare it with measurements. as a result, the model set up in this paper is proved to be applicable after all above - mentioned analyses
本文基於彈性理論和有限元原理與方法，分析了上埋式地下管道橫向力學計算方法和性狀並探討了上埋式地下管道的減荷等問題： （ 1 ）在分析現有幾種典型的管道垂直土壓力計算方法的基礎上，探討了影響垂直土壓力的主要因素以及改進的方法； （ 2 ）分別通過彈性理論分析法和結構力學的方法，建立了地下管道柔性圓環和剛性管涵的橫向靜力計算方程，並應用在算例中，把所得結果和有限元方法所得結果進行對比分析； （ 3 ）考慮填土、管道和基礎的共同作用、土體的非線性特性、初始應力場以及土體和管道的接觸面因素的影響，利用有限元的思路，建立了地下管道橫向力學有限元計算模型和方法，並且採用大型有限元分析軟體ansys ，針對上埋式管道工程算例，得出了管周土壓力以及管道橫截面應力的分佈狀況和規律，並和理論值進行對比；針對施加柔性填料的上埋式管道工程實例，得出了減荷后的土壓力分佈，並和實測值進行了對比。 -
Fabrication of the box beam is divided into such parts as reinforcement, formwork, concreting, prestressing, moving and storing of beam, pipe grouting under pressure, end sealing of the beam, water - proof layer on the bridge surface system, protective coating etc. the paper makes description of effective box beam construction technology and workmanship which can be adopted in other projects, such technologies as : manufacturing and fixing of reinforcement, steel reinforcement fixing baseplate, web plate and top plate respectively and lifting the steel skeleton into form, requirements of design and manufacturing and way of utilization for dismantling - erection type formwork and hydraulic formwork, optimization of concrete ratio, concrete pouring process of two ends of beam in priority over the middle, in sequence of first baseplate followed by web plate and top plate at last, concrete pouring in inclined section and in horizontal layer, concrete vibration mainly by external vibrator in assistance with internal vibrator, methods and regulation for steam curing of concrete, dual controls over stress and strain to ensure quality of prestressing workmanship, construction method of effective beam moving by heavy - weight special moving facility, some regulations and key notes about construction of grouting under pressure, beam ends sealing, water - proof layer on the bridge surface system, protective coating
箱梁製造由鋼筋工程、模板工程、混凝土工程、預應力工程、移存梁工程、孔道壓漿工程、梁體封端工程、橋面防水層和保護層工程等施工環節組成。文中介紹的採用胎具製作和綁扎鋼筋，分底腹板和頂板分別綁扎並吊裝鋼筋骨架入模；拆裝式和液壓式兩種模板的設計、製作要求和使用方法；綜合考慮、優化混凝土配合比，混凝土灌注從兩端至中間、先底板、后腹板、再頂板的施工順序和斜向分段、腹板水平分層、附著式振搗為主、插入式搗固為輔的施工工藝，蒸汽養護的方法和規定；應力應變雙控制確保預應力施工質量的施工技術；採用重物移運器有效移梁的施工方法；壓漿、封端、橋面防水層和保護層施工的一些規定和注意事項等都是對箱梁製造行之有效的施工技術和施工方法，並可為以後類似施工作借鑒。 -
Our main products include central material supply system, series drier, automatic charging machine, single double screw extruder, series heating and cooling blending machine, crusher, cold water machine, mould temperature controller, pipe, bar section, board, pp - r pipe, pe fuel pipe, plastic dual tubing extrusion production line and granulation completed production line equipment, at same time, we also carry on various plastic machine and refrigeration engineering. the products are sold well in every province and city of the whole country and also exported to about 30 countries and areas with strong technical force, advanced equipment, scientific management system and perfect after - sales service
公司主要產品有集中供料系統系列乾燥機自動加料機單雙螺桿擠出機粉料高速混合機粒料混合機螺旋上料機牽引機切割機離心脫水機化纖團粒機全自動擴口機全自動計量混合裝置破碎機磨粉機冷水機模溫機管材型材板材pvc管材pp - r管材pe供水燃氣管材中空壁纏繞管材硅芯管材生產線，雙管擠出電工穿線管材造粒等全套生產線設備。 -
The tsot has a great change in its structure compared with original heat pipe. it has a small hole on its top and several holes at the side of cooling section
這種熱管在構造上與一般的重力熱管相比有較大的改變：熱管本體頂端開孔，側端切向對稱開孔，因此稱為「切向漩流兩相半開式熱虹吸管」 。 -
Note : when actually applying, choose suitable type cable according to the pipe lenght, heat loss, work voltage, number of core wires. and core wire ' s section areas
注：實際選用時應根據管道長度、散熱量、工作電壓和芯線數，計算芯線截面而定。 -
2. wet zhou xiao of section, the leaking out rate of the tuber pipe is extremely low 3
2斷面濕周小，風管漏風率極率，僅0 . 02 % -
The evaporation section and the condensation section of the heat pipes can ben changed as the temperature of the outdoor air varies. so the heat pipe can be operated through the whole year. after analyzing the characteristics of energy recovery in air - conditioning system, associating heat feature of air - conditioning system with running environment
分析了空調系統排風能量回收的特點后，作者結合空調系統運行環境，建立了該傳熱裝置的數學模型，結果表明:熱虹吸管的傾斜角、充液率、管長和迎面風速對熱虹吸管的傳熱都有重要影響。
分享友人